LG Dryer Not Heating? Lessons From 350+ Repairs

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

When an LG electric dryer runs but does not heat, the thermal fuse is the most common part in our records, followed by the thermistor, the control board and a restricted vent. That is different from Samsung, where the heating element leads. We have repaired more than 350 LG dryers that were not heating. In the 31 calls with detailed notes in our current job system, the thermal fuse (6931EL3003D) was replaced in 5, the thermistor in 3, the control board in 3 and the vent was the problem in 3. A blown thermal fuse means the dryer overheated, so check the vent too.

This guide is written from our own job records. We have fixed more than 350 LG dryers that were not heating; 31 of those calls, from 2024 to October 2026, are in our current job system with detailed notes, across Westminster, Denver, Longmont, Lafayette, Erie, Boulder, Littleton, Broomfield and the rest of the metro. The photos are from those calls.

What 31 detailed LG calls show

What the technician noted Calls Typical part or fix
Thermal fuse 5 6931EL3003D
Thermistor 3 AGM30045804
Control board 3 EBR85130504, EBR85130517
Vent or duct restricted 3 Vent cleaning, vent line replaced
Gas dryer: igniter, flame sensor, gas valve 1 Gas valve coils, igniter
Power supply: one leg low 1 Electrical supply, not the dryer

Many notes only record the complaint, so these counts are minimums. Compare with Samsung dryers not heating, where the heating element is named in 31 of 82 calls: on LG the thermal fuse and the sensors come up first.

The thermal fuse

LG dryer with the front panel off and lint around the drum opening in Niwot
An LG dryer in Niwot with the front panel off and lint packed around the drum opening. The thermal fuse (6931EL3003D) and the drum belt were replaced.

The thermal fuse is a one-time safety part on the exhaust duct. When the dryer runs too hot, it opens and cuts the heat for good. The drum still turns and the timer still counts down, but the air stays cool. We replaced it in Lafayette (twice), Westminster, Boulder and Niwot, always part 6931EL3003D.

A blown fuse is a warning, not just a failed part. Lint in the cabinet, a long or crushed vent, or a clogged lint screen make the dryer overheat. On the Niwot call there was a lot of lint inside, and the drum belt was replaced at the same visit. If the cause is not fixed, the new fuse can blow again.

Thermistors and the D80 code

LG dryer in Broomfield with the old drum belt removed during a thermistor and belt replacement
An LG dryer in Broomfield that was not drying properly. The thermistor (AGM30045804) and the drum belt were replaced and the dryer was cleaned inside.

The thermistor tells the control board how hot the air is. When it reads wrong, the board cuts the heat too early or runs the cycle without proper heat, and the clothes come out damp. AGM30045804 shows up on our tickets in Longmont, Broomfield and Centennial. In Centennial the dryer was not drying completely and showed D80; the thermistor was replaced.

D80 on LG points to restricted airflow. It does not always mean a clogged vent, but always clean the vent and the lint screen first. In Longmont the owner of a 2-year-old LG dryer told us the vent had just been cleaned by an HVAC company; the thermistors and the control board were the parts we quoted.

The control board

LG dryer opened for a control board replacement in Longmont
An LG dryer in Longmont opened for service. The control board (EBR85130504) was replaced.

When the fuse, the thermistor and the element all test fine but the heater gets no power, the control board is the next suspect. We replaced boards in Longmont, and in Arvada the dryer control board needed to be replaced.

Power and the vent

Power cord terminal block of an LG dryer in Longmont with a low-voltage supply leg
The power cord terminal block of an LG dryer in Longmont. One leg of the power supply measured only about 50 volts, so the dryer could not heat.

An electric dryer needs 240 volts on two legs. The motor and the drum run on one leg, so the dryer turns even when the heat is dead. In Longmont one leg read only about 50 volts: the problem was the supply, not the dryer. Check the double breaker before you call.

The vent is the other common cause. In Lone Tree the filter and the vent duct were cleaned, and in Erie a clogged vent line was replaced. See our dryer vent cleaning service.

LG gas dryers

Vent connection behind an LG gas dryer in Denver
The vent connection behind an LG gas dryer in Denver. The igniter, the flame sensor and the gas valve were replaced.

On a gas dryer there is no thermal fuse to blame first. The igniter, the flame sensor and the gas valve coils work together; when one fails, the burner does not light or goes out. In Denver all three were replaced.

Video: why an LG dryer won’t dry

Video by LG USA

What we see on Denver calls

  • On our 31 detailed LG no-heat calls, the thermal fuse 6931EL3003D came up most: 5 calls. Then the thermistor AGM30045804 (3) and the control board (3).
  • Restricted vent or duct: 3 calls.
  • One call was a low power leg at the outlet: an electrical supply problem, not the dryer.

Don’t want to do it yourself? Call 720-230-1229.

Safe checks before you call

  1. Clean the lint screen and run a timed high-heat cycle with a small load.
  2. Check the breaker panel: an electric dryer uses a double breaker. Switch it fully off and on.
  3. Feel the air at the outside vent hood. Weak airflow points to a clogged or crushed vent.
  4. If the display shows D80, D90 or D95, clean the vent from the dryer to the outside.
  5. Make sure you are not using an air-dry or low-heat setting.
  6. Write down the model number from the label inside the door, such as DVL60M9900VA3.

What it costs

On our price list a thermal fuse or heating element starts from $179 for labor, a control board from $259, and belts or rollers from $259, with parts quoted separately. The home diagnostic visit is from $59 and is credited toward the repair. See our prices.

When to call a technician

  • The dryer runs but the air stays cool after you have checked the breaker and the vent.
  • The heat stopped right after a long or heavy cycle.
  • D80 keeps coming back after the vent has been cleaned.
  • You smell burning or see scorch marks. Unplug the dryer.

We repair LG dryers across 52 Denver-area cities. See LG dryer repair, LG dryer error codes, LG dryer making noise and our general guide to dryers not heating.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

Why is my LG dryer running but not heating?

In our records the most common cause is a blown thermal fuse (6931EL3003D). A thermistor, the control board, a restricted vent or one dead leg of the power supply can cause the same symptom.

Why did my LG dryer thermal fuse blow?

Because the dryer overheated, usually from lint or a restricted vent. Clean the vent and the inside of the dryer when you replace the fuse, or it can blow again.

What does D80 mean on an LG dryer?

It points to restricted airflow, usually the vent. If the vent is clean and the code stays, a thermistor or another part may be reading wrong.

My LG dryer is new and the vent was just cleaned. Why is it not drying?

Then the sensors or the control board are more likely. On one of our calls a 2-year-old LG dryer with a freshly cleaned vent needed thermistors and a control board.

Is it worth fixing an LG dryer that is not heating?

Usually yes. A thermal fuse or a thermistor is one of the less expensive dryer repairs.

720-230-1229
720-230-1229
Call Now Book Online