Whirlpool Refrigerator Not Cooling? Lessons From 400+ Repairs

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

When a Whirlpool refrigerator stops cooling, the most common cause in our records is a defrost problem: the evaporator coil ices over and cold air can no longer reach the food. The main control board and the compressor or sealed system follow. We have repaired more than 400 Whirlpool refrigerators that were not cooling. In the 48 calls with detailed notes in our current job system, defrost problems came up in 10, the control board in 8 and the compressor or sealed system in 8. Before you call, check that cooling has not been switched off on the display.

This guide is written from our own job records. 48 of our Whirlpool not-cooling calls, from late 2023 to October 2026, are in our current job system with detailed notes, across Longmont, Boulder, Denver, Englewood, Centennial, Commerce City, Westminster, Broomfield, Erie and the rest of the metro. The photos are from those calls.

What 48 detailed Whirlpool calls show

What the technician noted Calls Typical part or fix
Defrost: iced-over evaporator, heater contacts, sensor or defrost control 10 W11087438 fan assembly with defrost sensor, heater contact repair
Main control board 8 WPW10503278, W11133692, W10811365
Compressor or sealed system 8 W11727250 compressor, sealed-system repair
Evaporator or freezer fan 4 W11224591, W11455373
Fixed by a setting or a restart 3 Cooling switched back on, power cycle
Condenser cleaning, start relay, drain 3 Cleaning, Supco relay

Notes are short and one call can fall in more than one row, so these are minimums. Each brand fails in its own way. On LG the compressor leads, on GE the fans lead, and on Whirlpool the defrost system and the control board account for most of the work.

The most common Whirlpool problem: an iced-over evaporator

Fresh-food evaporator of a Whirlpool French-door refrigerator buried in ice in Englewood
The fresh-food evaporator of a Whirlpool French-door refrigerator in Englewood, buried in ice. We defrosted it and replaced the fan assembly.

A refrigerator makes cold air at the evaporator coil and melts the frost off that coil several times a day with a defrost heater. If the heater, its sensor or the control that runs it stops working, frost builds up until the coil is a solid block and air cannot pass through it.

Many Whirlpool French-door models have a second evaporator just for the fresh-food section, behind a panel at the back of the fridge. That is where we find the ice most often on Whirlpool. On two calls, in Thornton and Englewood, the fresh-food evaporator was covered in ice and we replaced the fan assembly with its defrost sensor (W11087438).

Thermometer reading about 52 degrees in a Whirlpool refrigerator in Thornton
The fresh-food section of a Whirlpool in Thornton read about 52°F. The fresh-food evaporator was covered in ice.

On side-by-side models we also find burned contacts at the defrost heater. On calls in Erie and Louisville the ice was melted with a forced defrost and the heater contacts were repaired. When the contacts burn, the heater gets no power even though the heater itself is fine.

Frost covering the evaporator of a JennAir refrigerator built by Whirlpool in Boulder
The evaporator of a JennAir refrigerator (built by Whirlpool) in Boulder, covered in frost.
Evaporator of a JennAir refrigerator after defrosting in Boulder
The same evaporator after defrosting. The bimetal sensor and the heating element tested fine.

Defrosting brings cooling back for a while, but the ice returns in days or weeks if the cause is not fixed. That is why we test the heater, the sensor and the control before we leave.

The control board

Main control board of a Whirlpool side-by-side refrigerator in Boulder
The main control board of a Whirlpool side-by-side in Boulder, in the housing at the top of the fresh-food section. The repair called for a new board (WPW10503278).

On many Whirlpool side-by-side refrigerators the main control board sits in a housing at the top of the fresh-food section. It runs the compressor, the fans and the defrost. When it fails, the refrigerator can stop cooling completely, run the fan nonstop, or stop defrosting. The board WPW10503278 appears on four of our tickets, in Berthoud, Boulder, Englewood and one more call; on the Englewood call the ice was melting and the new board was installed and programmed.

On a Westminster call (WRS325SDHB01) the refrigerator would not enter test mode, so power to the heater could not be checked, and the board was the next suspect. Newer boards often need to be set up for the model after installation.

Compressor and sealed system

Evaporator of a Whirlpool side-by-side refrigerator with a sealed-system problem in Littleton
The evaporator of a Whirlpool side-by-side (WRS325FDAM04) in Littleton. The freezer was not cooling efficiently and the sealed system needed repair.

A compressor or sealed-system problem came up in 8 of our 48 detailed calls: compressors replaced or needed in Centennial, Longmont, Denver and Commerce City, sealed-system repairs in Centennial and Littleton, and a freezer evaporator replaced in Erie. In Commerce City both the inverter board and the compressor needed to be replaced. Sealed-system work needs an EPA 608 certified technician.

Not every warm Whirlpool needs a part

Thermometer reading about 54 degrees in a Whirlpool refrigerator with cooling switched off in Broomfield
The fresh-food section of a Whirlpool in Broomfield read about 54°F. Cooling had been switched off on the display; turning it back on was the fix.

On three calls no part was needed. In Broomfield cooling had been switched off on the display, which happens with showroom or vacation settings. In Longmont and Boulder a restart brought the refrigerator back. If a restart works, keep an eye on it: a defrost problem can look solved for a while after the ice melts.

Video: freezer cold, refrigerator warm

Video by AppliancePartsPros

What we see on Denver calls

  • The video walks through defrost and fan problems, the same pattern we see. On our 48 detailed Whirlpool calls, defrost problems were the most common cause: 10 calls (W11087438 fan assembly with defrost sensor, heater contact repair).
  • Main control board: 8 calls. Compressor or sealed system: 8 calls.

Don’t want to do it yourself? Call 720-230-1229.

Safe checks before you call

  1. Put an appliance thermometer in a glass of water on the middle shelf and read it after a few hours. Above 40°F means food is at risk.
  2. Check the display for a Cooling Off, demo or vacation setting, and that the set points are about 37°F and 0°F.
  3. Look for frost on the back wall of the freezer or behind the panel at the back of the fridge.
  4. Listen for the fans. A fan that runs nonstop or not at all is a clue.
  5. Vacuum the condenser coil at the bottom and keep the front grille clear.
  6. Restart the refrigerator once by unplugging it for a minute. If the problem returns, call.
  7. Write down the model number from the label inside the fridge, such as WRS325SDHB01, WRS325FDAM04 or WRX735SDBM00.

What it costs

On our price list a defrost heater, sensor or defrost repair starts from $179 for labor, a fan motor or the control board from $259, and compressor or sealed-system work from $479, with parts quoted separately. The home diagnostic visit is from $59 and is credited toward the repair. See our prices.

When to call a technician

  • The fridge reads above 40°F after you have checked the settings and cleaned the condenser.
  • Ice builds up on the freezer wall or behind the fresh-food panel.
  • The refrigerator cooled again after being unplugged and then warmed up again.
  • The fan runs nonstop or the compressor clicks on and off.

We repair Whirlpool, KitchenAid, Maytag and JennAir refrigerators across 52 Denver-area cities. See Whirlpool refrigerator repair, Whirlpool refrigerator error codes and our general guide to refrigerators not cooling.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

Why is my Whirlpool refrigerator not cooling but the freezer is cold?

Most often the fresh-food evaporator or the air path to the fridge is blocked by ice, or a fan has stopped. On Whirlpool French-door models the fresh-food evaporator has its own fan and defrost sensor, and that assembly is a common repair in our records.

Why does my Whirlpool refrigerator work again after I unplug it?

Unplugging lets the ice on the evaporator melt and resets the control board. If the cause is a defrost fault, the ice comes back in days or weeks and the fridge warms again.

Where is the control board on a Whirlpool side-by-side?

On many models it sits in a housing at the top of the fresh-food section, behind the light and control panel. It runs the compressor, fans and defrost.

How do I turn cooling back on on a Whirlpool refrigerator?

Many Whirlpool models have a Cooling Off or showroom setting that keeps the lights and display on with no cooling. The button combination depends on the model; check your manual.

Is it worth repairing a Whirlpool refrigerator that is not cooling?

Usually yes. Defrost repairs, fans and boards are moderate repairs. Compressor or sealed-system work costs more and is worth comparing with a new refrigerator on older units.

720-230-1229
720-230-1229
Call Now Book Online