Ice Maker Repair for Home Refrigerators
Same-day ice maker repair in 52 Denver-area cities. Refrigerator, built-in and undercounter ice makers, all major brands.
Ice maker repair in Denver and the surrounding Front Range, taken from 640+ ice maker tickets in our service records. Since 2024 our technicians have worked on more than 640 ice makers. Most were built into refrigerators, some were undercounter units in kitchens and bars, and a few dozen were commercial ice machines in businesses and a school. This page is built from the notes and photos on those tickets. It explains why ice makers stop, why they freeze up or leak, which parts we replace most and when a cleaning is all a machine needs.

Six hundred ice maker calls, sorted
We pulled every ticket since 2024 where the job type was an ice maker or the notes mentioned the ice maker, ice dispenser or ice machine. One ticket can describe more than one symptom, and the numbers are rounded.
| What was wrong | Tickets (approx.) | Typical cause we found |
|---|---|---|
| Water supply or valve problem | 100 | Failed or clogged inlet valve, kinked line, frozen fill tube |
| Dispenser not giving ice or water | 90 | Iced-over chute, dispenser motor or switch, filter housing |
| Leaking | 75 | Misrouted or cracked fill tube, overfilling, a blocked defrost drain |
| No ice at all | 55 | Ice maker assembly or its control, no water reaching it, freezer too warm |
| Cleaning or descaling requested | 50 | Scale and slime in commercial and undercounter machines |
| Commercial ice machine | 45 | Dirty condenser, scale, pumps, sensors, harvest problems |
| Small, hollow or slow ice | 30 | Low water flow, an old filter, low pressure, a weak valve |
| Ice maker frozen or jammed | 25 | Ice buildup inside the compartment, warm air leaking into it |
| Error code | 25 | Ice maker self-test failure, sensor or harvest fault |
Looking only at parts named in the notes: the ice maker assembly itself appears on about 120 tickets, water inlet valves on about 50, fans on about 45, control boards on about 30, defrost parts on about 28 and thermistors or sensors on about 18. In other words, a new ice maker is the most common single repair, but on many visits the ice maker itself was fine and the real problem sat upstream.
Brands and where they fail
Samsung leads our ice maker records by a wide margin, with roughly 95 tickets. LG, Whirlpool and GE follow with about 55 to 65 each, then KitchenAid, Kenmore and Frigidaire. Premium refrigerators show up too: Bosch, Sub-Zero, Viking, Monogram and JennAir. Commercial machines are mostly Scotsman, Manitowoc and Hoshizaki.
- Samsung French door models carry the ice maker in the fresh food door. When warm, moist air reaches that compartment, ice builds up around the unit and the dispenser jams. The fix we use is to seal the housing and, where needed, replace the ice maker (recent installs include DA97-07365G and DA97-18859A). See Samsung ice maker repair.
- LG: ice maker assemblies (AEQ73130004, AEQ72909603) and fill tubes that freeze shut. See LG ice maker repair.
- Whirlpool, KitchenAid, JennAir, Maytag: ice makers that fail the harvest or fill test, inlet valves and ice maker control boards. See Whirlpool, KitchenAid and Maytag.
- GE and Monogram: ice makers (WR30X28682 and the older WR30X10093 kit) and dual valves. See GE ice maker repair.
- Also: Kenmore, Frigidaire, Electrolux and Sub-Zero.
When the ice maker is the problem
Every refrigerator ice maker runs the same cycle: a valve fills the mold, the freezer turns the water to ice, a small heater or a twist loosens the cubes, and an arm or motor pushes them into the bin. A shut-off arm or sensor stops production when the bin is full. Many modern ice makers have a built-in test mode. When an ice maker gets power but can’t complete a harvest or fill test, the unit is usually at fault.

A Kenmore side-by-side in Niwot had power to its ice maker but could not run any test; the ticket called for a new ice maker (2198597). A KitchenAid in Greenwood Village failed both the harvest and fill tests and needed a new ice maker and a new inlet valve. A JennAir in Louisville was making “big blocks” instead of cubes, usually a sign the mold is overfilling or not ejecting; the assembly was replaced (W11391031). And a KitchenAid in Brighton showing an E5 code got a new ice maker as well.

Sometimes the control, not the ice maker, has failed. A Whirlpool side-by-side in Centennial needed a receiver and a control board; a Whirlpool in Longmont needed ice maker control board W10446514. For quick checks at home, see ice maker not making ice.

When the water never arrives
About a hundred of our tickets traced back to the water side. The inlet valve at the back of the refrigerator is an electric solenoid; when it weakens, the ice maker cycles empty or makes thin, hollow cubes. A clogged screen, a kinked line or low house pressure produces the same symptoms. In Arvada a clogged line to the ice maker ended with a new inlet valve (WR57X27487). In Lakewood a Whirlpool needed valve W11645245. A GE Monogram in Littleton went through a harvest with an empty mold; the valve was the cause, and the tech found a separate water leak during the repair.
A Viking in Denver had both problems at once: the water dispenser only trickled and the ice maker was dead. It needed a new water valve and a new ice maker.

A filter can starve an ice maker too. A Samsung in Broomfield needed a new filter housing along with its ice maker, and another Broomfield owner reported cloudy water and no fill right after changing the filter. If a new filter goes in and the ice stops, check that it is fully seated, or try the bypass plug if your model has one. Need a new line run to the refrigerator? We also do refrigerator water line installation.
Frozen fill tubes, ice buildup and leaks
The fill tube carries water from the valve into the freezer. If the freezer runs too cold, the valve drips, or warm air reaches the tube, it freezes shut. The next fill then overflows onto the shelves or down the back. In Niwot an LG owner defrosted the refrigerator herself and then found two leaks; thawing the frozen fill tube was the whole fix.

Installation matters. A Kenmore in Denver had a new ice maker put in a year earlier by someone else, and the fill tube had been installed incorrectly, so water ran where it shouldn’t. In Aurora a Whirlpool’s fill tube leaked long enough to damage the floor; the tech shut off the water first. And a KitchenAid in Boulder that seemed to leak from the ice maker actually had a blocked evaporator drain, cleared by cleaning the drain system and defrosting.
Samsung French door owners know a related problem: ice packing up inside the door compartment. In Centennial one Samsung needed a forced defrost, a new defrost thermistor and temperature sensor, a new evaporator fan, a sealed ice maker housing and a new ice maker. Not every case is that big, but a compartment that keeps icing will come back unless the housing is sealed. See refrigerator leaking water for more.
Check the freezer before the ice maker
An ice maker can only work if the freezer is cold enough, ideally around 0°F. Our technicians carry infrared thermometers and check freezer and fresh food temperatures as a routine part of refrigerator calls. When the freezer sits in the teens or twenties, ice production slows or stops, and the real repair is a fan, a defrost part or the sealed system. That is why some “ice maker” tickets in our records ended with a condenser fan, an evaporator fan or a defrost repair instead.
Garage refrigerators are a Colorado special case. In winter the garage can be colder than the freezer setting, so the compressor barely runs and the freezer warms up. Read garage refrigerators in Colorado winters. If the whole refrigerator is warm, go to our refrigerator repair or freezer repair pages.

Dispenser trouble: ice in the bin, nothing at the door
Around 90 tickets mentioned the dispenser. If the bin is full but nothing comes out of the door, the ice maker is doing its job and the fault is downstream: cubes frozen into a solid block in the bin, a chute blocked by ice, a jammed auger, a failed auger motor, a door switch or the dispenser control. When the water side of the dispenser fails as well, look at the filter, its housing and the lines in the door.
Recent examples from our tickets: a Whirlpool in Arvada needed a dispenser control board (W10740218). A Samsung in Broomfield with a water dispenser problem needed a new filter housing (DA97-23545A). In Longmont a refrigerator leaking at the dispenser needed a new dispenser shield assembly and a repair to the water line at the back. In Centennial an owner changed the filter, then found the water dispenser dead and ice building up in the freezer, two symptoms that often go together when water ends up in the wrong place.
Before booking, empty the bin, break up any clumps and put it back firmly. If cubes drop from the ice maker but don’t reach the door, the auger or chute is the likely culprit. If you hear the auger motor hum without turning, stop pressing the paddle; forcing it can strip the gears.
Before you call: five quick checks
- Is the ice maker switched on? Many have a switch or a setting on the display, and the shut-off arm may be stuck in the up position.
- Is the freezer cold enough? A freezer thermometer should read close to 0°F.
- Is water getting to the refrigerator? Try the water dispenser. If it is slow too, check the shut-off valve, the filter and the line behind the refrigerator.
- Did you just change the filter? Remove it and reinstall it, making sure it locks fully.
- Is there ice where it shouldn’t be? Frost around the ice maker, a frozen fill tube or a solid block in the bin points to a defrost, sealing or airflow problem.
If none of that helps, write down the model number from the label inside the fresh food section and book a visit. Having it ready lets our technician bring the right ice maker or valve the first time.
Undercounter ice makers
Built-in undercounter ice makers in kitchens, basements and wet bars work differently from refrigerator units. Many make clear ice on a chilled plate and recirculate water with a small pump; some have a drain pump. They also have their own condenser, which pulls kitchen air through a small grille at the front.

Recent undercounter jobs: a GE unit in Longmont was beeping; the condenser needed cleaning and a kinked water hose needed straightening. An undercounter machine in Fort Lupton wasn’t filling or cooling; it needed an ice bin thermostat and a condenser cleaning. A KitchenAid in Arvada with a circulation pump that wouldn’t run needed a new control board (W11034363). These units are sensitive to dust and lint at the grille, so vacuum it every few months.
Commercial ice machines
For businesses we service Scotsman, Manitowoc and Hoshizaki machines. Commercial machines fail differently from household units: water quality and maintenance decide most of their problems. Mineral scale coats the evaporator plate and water trough, slime grows in the splash zone, and dirty condensers drive up head pressure until the machine trips or runs long.

A Manitowoc Indigo NXT in Denver needed calibration and a cleaning. A commercial machine in Lakewood beeping three times was reporting a freeze time fault; after a reset it ran a normal cycle. A Scotsman in Broomfield needed a new ice thickness sensor (A39031-021). In Longmont we cleaned an ice machine and replaced its dump valve during a visit that covered four commercial refrigerators. And in Broomfield one business books us every year for a deep clean: descaling and sanitizing.


Most manufacturers call for cleaning and sanitizing at least twice a year, more in heavy use. Our dedicated commercial ice machine repair page covers this in depth, and commercial preventive maintenance plans can put it on a schedule.

Recent ice maker repairs
- Aurora, Oct 2026. Samsung stopped making ice. Ice maker DA97-07365G.
- Centennial, Oct 2026. Whirlpool side-by-side ice maker dead. Receiver and control board.
- Longmont, Oct 2026. Samsung ice maker. Condenser cleaning, housing sealing, OEM ice maker.
- Longmont, Oct 2026. GE undercounter beeping. Condenser cleaning, hose fixed.
- Broomfield, Oct 2026. Annual ice machine descaling and sanitizing.
- Brighton, Sep 2026. KitchenAid with E5. New ice maker assembly.
- Lakewood, Sep 2026. Whirlpool not making ice. Water valve.
- Niwot, Aug 2026. LG leaking after a home defrost. Frozen fill tube thawed.
- Arvada, Aug 2026. Clogged line to the ice maker. Inlet valve.
- Thornton, Jul 2026. Ice buildup in the ice maker. Defrosted, condenser cleaned.
- Boulder, Jul 2026. Hoshizaki not making ice. Pump replaced.
- Denver, Jul 2026. Viking, no ice and weak water. Valve and ice maker.
Denver, Longmont, Broomfield, Boulder, Littleton, Erie and Arvada send us the most ice maker calls.
What ice maker repair costs
| Repair | Starts at |
|---|---|
| Water inlet valve | $179+ |
| Ice maker assembly | $259+ |
| Auger or dispenser motor | $259+ |
Home visits begin with a diagnostic from $59 that is credited toward the repair if you go ahead. You see the price before we start, and our parts and labor are covered for 90 days.
Replace the ice maker or the refrigerator?
An ice maker or valve on a refrigerator that otherwise cools well is almost always worth replacing. The question changes when the refrigerator itself has a sealed system problem, like a refrigerant leak, or when the ice compartment keeps icing despite repairs. On one Longmont return visit this October the real problem turned out to be a refrigerant leak, and the new ice maker came back out. We’ll tell you honestly when an ice maker repair would be money spent on the wrong part.
Keep the ice coming
- Change the water filter on schedule, and make sure the new one clicks fully into place.
- Keep the freezer near 0°F and don’t block the vents inside it with food.
- Use the ice regularly. Cubes left for weeks clump and jam the auger.
- Don’t chip at ice in the bin or chute with knives; it breaks arms and cracks housings.
- Turn the ice maker off if the water supply is shut off, so it doesn’t run empty.
- Clean undercounter and commercial machines on the maker’s schedule, and keep the condenser grille free of dust.
Look up your refrigerator’s codes on our pages for Samsung, LG, GE, Whirlpool, KitchenAid and Sub-Zero.
Restaurant, bar or hotel ice machine down? Hoshizaki, Manitowoc and other commercial ice machines are handled by our commercial team. See commercial ice machine repair → Diagnostic $129, credited to the repair.
Common Ice Maker Repair for Home Refrigerators Issues We Fix
How much does ice maker repair for Home refrigerators cost in Denver?
Ice Maker Repair for Home Refrigerators starts at $179*. The $59 service call is free when we do the repair, and you approve a written quote before any work begins.
| Repair | From* |
|---|---|
| Water inlet valve | $179+ |
| Ice maker assembly | $259+ |
| Auger or dispenser motor | $259+ |
* Starting prices are for labor; parts are listed separately in your written quote. Final price depends on the model and diagnosis.
See full price list →Frequently Asked Questions
The most common causes we find are a failed ice maker assembly, a water inlet valve that no longer opens, a frozen fill tube, or a freezer that isn't cold enough. A technician checks the freezer temperature and the water supply first, then runs the ice maker's own test cycle to see whether the unit itself has failed.
On Samsung French door refrigerators the ice maker sits in the fresh food door, and warm, moist air leaking into that compartment freezes around it. Defrosting alone only buys time. The lasting fix we use is to seal the ice maker housing and replace any parts the ice has damaged.
Small or hollow cubes mean the mold isn't getting enough water. Common causes are an old or poorly seated filter, low water pressure, a kinked supply line or a weak inlet valve. Replace the filter first; if the cubes stay small, the valve is the next suspect.
Yes. We service Scotsman, Manitowoc and Hoshizaki machines for businesses around the Denver metro, including pumps, sensors, valves, cleaning, descaling and sanitizing. Regular cleaning prevents most of the problems we see on commercial units.
If the refrigerator cools properly, replacing the ice maker or its water valve is usually the better choice. If the refrigerator has a sealed system problem such as a refrigerant leak, a new ice maker won't help, and our technician will tell you before any parts go in.
More About Ice Maker Repair
Ice Maker Repair by brand
Troubleshooting guides
Maintenance guides
Service areas
No ice?
Call 720-230-1229 or book online. Same-day ice maker repair across the Denver metro, service fee waived with repair.

