KitchenAid Dishwasher Repair
KitchenAid dishwasher repair in Denver: not draining, leaks, dishes not clean, F9E1, F7E2 and other codes, won't run. 24/7, 90-day warranty.
KitchenAid dishwasher repair in Denver: not draining, leaks, dishes not clean, error codes and dishwashers that won’t run. We repair KitchenAid built-in and panel-ready dishwashers across Denver and 30 nearby cities, 24/7.
4.9★ on Google · $99 service call waived with the repair · Written quote before any work · 90-day warranty on parts and labor · EPA 608 certified technicians · Same-day or next-day visits
Since January 2024 we have completed about 85 KitchenAid dishwasher calls. About one in five came in with an error code, about one in six was a drain problem, and about one in seven was a leak. The parts we replaced most often were the circulation pump (wash motor), drain pumps, spray arms, filters, diverter motors and control boards.
KitchenAid is part of Whirlpool, and KitchenAid dishwashers share their platform and many parts with Whirlpool and Maytag dishwashers. What sets most KitchenAid models apart is a stainless tub, a heavier door, and a removable cylindrical filter that needs regular cleaning.
1. Dishes not clean, or the wash motor stops
The circulation pump, which KitchenAid also calls the wash motor, pushes water through the spray arms. When it fails, the dishwasher fills and drains but barely washes, often with an error code. On several of our 2026 calls the display showed F7E1, and on most of them the wash motor had failed. KitchenAid’s own list includes F7E2, a wash motor error.
- Filter. The cylindrical filter in the bottom of the tub twists out. A clogged filter starves the pump; in January 2026 we replaced the filter on a KitchenAid.
- Spray arms. A cracked or broken arm loses pressure. In October 2026 a broken spray arm was why dishes weren’t getting clean.
- Diverter motor. It sends water to the upper or lower arms; when it fails, one rack stays dirty.
2. Not draining (F9E1, F9E2)
KitchenAid lists F9E1 as a long drain and F9E2 as a drain motor error. Start with the filter, the drain hose, the disposer and the air gap. After that, the drain pump: several of ours were simply clogged and cleaned out; others needed replacing.
3. Leaking (F8E4)
Many KitchenAid dishwashers have a drip tray with a float switch, and KitchenAid lists F8E4 as water detected in the drip tray. The water itself usually comes from a pump seal, a hose, the water inlet valve, a float switch, or the diverter; in June 2025 a leaking KitchenAid needed a new float switch, and in August 2026 another needed a new diverter motor. Using dish soap instead of dishwasher detergent also causes leaks at the door.
4. Won’t start, stops or trips the breaker
- Door latch. The dishwasher won’t run if the door doesn’t latch.
- Control board. In July 2025 and February 2026 KitchenAid dishwashers needed new control boards. KitchenAid lists F6E1 as a user interface or main control error.
- Heating element. A shorted element can trip the breaker. KitchenAid lists F4E3 as a heating error.
- Wiring. In June 2026 a KitchenAid that kept turning off had burnt wiring.
From our service log
- March 2024, not working. A new circulation pump and diverter motor.
- November 2024, leaking while running. We replaced the heating element.
- June 2025, leaking. We replaced the float switch and float.
- February 2026, not cleaning properly. A new diverter motor.
- July 2026, F4E3 and F7E1. The wash motor had failed and was replaced.
- October 2026, F8E1 and dirty dishes. A broken spray arm; we replaced it.
KitchenAid dishwasher codes
From KitchenAid’s published list. Codes vary by model; check your manual for yours.
| Code | What KitchenAid says it means |
|---|---|
| F9 E1 | Long drain, not draining. |
| F9 E2 | Drain motor error. |
| F8 E4 | Water detected in the drip tray. |
| F7 E2 | Wash motor error. |
| F6 E1 | User interface error, main control. |
| F4 E3 | Heating error. |
| H2O | Not detecting water. |
On models without a display, the Clean light flashes the code: count the first set of flashes (the F number), then after a short pause the second set (the E number).
Code still on the display? Call 720-230-1229. We answer 24/7 and can usually be there the same or next day.
Before you call: three quick checks
- Twist out the filter and rinse it under running water.
- Reset the power. KitchenAid recommends unplugging the dishwasher, or turning off its breaker, for 30 seconds.
- Use dishwasher detergent only, never dish soap.
Still having trouble with your KitchenAid dishwasher? Call 720-230-1229. We answer 24/7 and can usually be there the same or next day.
Repair or replace?
KitchenAid dishwashers are built to last, and circulation pumps, drain pumps, diverters, spray arms, filters, floats and control boards are almost always worth repairing. When an older unit needs a pump and a board at the same time, or has water damage underneath, we give you an honest repair-versus-replace number. Either way, you get a written quote before any work starts, and the $99 service call is waived if you go ahead with the repair.
KitchenAid dishwasher repair near you
We repair KitchenAid dishwashers in Denver and every city we serve across the metro, with same-day or next-day visits. Tap your city to see local service details:
Related: KitchenAid appliance repair · KitchenAid refrigerator repair · Whirlpool dishwasher repair · Dishwasher repair
Common KitchenAid Dishwasher Problems
Why Choose The Appliance Team?
Denver's trusted appliance repair company — professional service you can count on.
Same-Day Service
Same-day appliance repair in Denver — call early and we can often be there today. No waiting around for weeks.
90-Day Warranty
90-day warranty on parts and labor for every repair we perform.
Certified Technicians
Our Denver appliance repair technicians are trained on all major brands and use genuine manufacturer parts.
Transparent Pricing
Service fee waived with repair. No hidden charges, no surprises.
Frequently Asked Questions
Clean the cylindrical filter first. If dishes are still dirty, the most common causes are a failed circulation pump (wash motor), a broken spray arm or a failed diverter motor.
KitchenAid lists F9E1 as a long drain. Clean the filter and check the drain hose, disposer and air gap. If it still won't drain, the drain pump may need cleaning or replacing.
Common causes are a pump seal, a hose, the water inlet valve, the float switch or the diverter, or dish soap used instead of dishwasher detergent. On many models, F8E4 means water has reached the drip tray.
KitchenAid is part of Whirlpool, and many KitchenAid dishwasher parts are shared with Whirlpool and Maytag models, which keeps them easy to get.
The service call is $99 and is waived if you go ahead with the repair. You get a written quote for parts and labor before we start, so there are no surprises.
KitchenAid dishwasher not cleaning?
Call 720-230-1229. We answer 24/7 and send a technician the same or next day. 90-day warranty on parts and labor.
