Viking Range and Oven Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

Most Viking range codes point to the oven temperature sensor (RTD), the self-clean door latch, or the control. On older gas self-clean ranges the code is a pattern of the Cycle and Clean lights; on touch-control ovens it is a text message such as RTD ERROR or LATCH ERROR; on gas wall ovens it is F1, F2 or F3. A breaker reset can clear a one-time glitch, but sensor, latch and runaway-temperature faults need a technician.

Viking has used several control types over the years, so the same problem can show up differently by model. Professional gas self-clean ranges (VGSC) flash the Cycle and Clean indicator lights, touch-control wall ovens spell out the fault, and induction and electric cooktops use their own short codes. The list below comes from Viking use and care guides and service manuals, plus a few codes commonly reported by repair references. Turn off power, and gas on gas or dual fuel models, before any hands-on check.

Viking Range and Oven error codes and what they mean

Code What it means What to try
Cycle flashing, Clean off (VGSC gas self-clean ranges) Oven temperature sensor (RTD) error on the right-hand oven of 30, 36 and 48 inch models.
Call a technician
Turn off power at the breaker for a few minutes, then retry. If the pattern returns, the RTD needs testing and likely replacement by a technician.
Cycle on/off 1 second, Clean off (VGSC) RTD (oven probe) error, per the VGSC service manual.
Call a technician
Reset the breaker. If it returns, call for service.
Cycle off, Clean flashing (VGSC) Self-clean door latch error on the right-hand oven.
Call a technician
Let the oven cool fully, make sure the door is closed tightly and the knob is set correctly, then reset the breaker. If the pattern returns, call for service.
Cycle off, Clean on/off 1 second (VGSC) Door latch error on the right-hand oven.
Call a technician
Let the oven cool and reset the breaker. If it returns, call for service.
F1 (VGSO gas wall oven) Shorted oven temperature probe (RTD).
Call a technician
Reset power. If F1 returns, the RTD or its wiring needs testing by a technician.
F2 (VGSO gas wall oven) Open oven temperature probe (RTD).
Call a technician
Reset power. If it returns, the RTD needs replacement.
F3 (VGSO gas wall oven) Controller malfunction.
Call a technician
Reset power. If it returns, call for service.
RTD ERROR (touch-control ovens) Oven temperature sensor open or shorted.
Call a technician
Reset the breaker. If it returns, call for service.
LATCH ERROR (touch-control ovens) The door latch cannot lock or unlock.
Call a technician
Let the oven cool completely and reset the breaker. If the door stays locked or the message returns, call for service.
PROBE ERROR (touch-control ovens) Meat probe open or shorted. Unplug the probe, check that the jack is dry and clean, and try again. If it persists without the probe, call for service.
KEYBOARD ERROR (touch-control ovens) No connection between the keyboard (touch panel) and the control.
Call a technician
Reset the breaker. If it returns, call for service.
MODEL ERROR (touch-control ovens) Incorrect model number set in the control, usually after a control replacement.
Call a technician
Call for service so the control can be configured.
Runaway oven temperature (VDSC dual fuel) The control detected the oven temperature rising well past the set point, above the 650 degree limit, with the door unlocked.
Call a technician
Turn the oven off at the breaker and do not use it. Call for service.
Red knob backlight (7 Series illuminated-knob ranges) Viking's guide says red backlighting signals an error. Pulsing lights during preheat are normal.
Call a technician
Note the color and pattern, reset the breaker, and call for service if it returns.
Induction flash codes 1 / 3 / 5 / 6 / 8 (older induction cooktops and rangetops) Flashes per group: 1 power device over temperature, 3 power device malfunction, 5 power device temperature sensor fault, 6 coil temperature sensor fault, 8 inside temperature too high.
Call a technician
Turn the unit off and let it cool. Make sure the cooling air inlet is not blocked. If the code returns, call for service.
Induction flash code 9 Cookware is not compatible with induction. Use a magnetic pan that a magnet sticks to firmly, centered on the zone.
E1 / Er03 (3 Series induction) An object or liquid is covering the control keys. Wipe the control area dry and remove any items from it.
E2 / E H (3 Series induction) Cooktop overheated. Turn it off and let it cool. Check that the ventilation under the cooktop is not blocked.
E3 / E6 / E8 / E (3 Series induction) E3 pan not suitable, E6 electrical supply problem, E8 fan air inlet blocked, E alone electronic failure. Use suitable cookware and clear the air inlet. For E6 or E, reset the breaker; if it returns, call for service.
FE / Ft / Fc / Fr / FH (Designer electric cooktops) FE or Ft temperature sensor failure, Fc over temperature, Fr relay error, FH control (memory) error.
Call a technician
Turn the cooktop off and let it cool, then reset the breaker. If it returns, call for service.
FA / FC / FJ / FU / FL / Fb / Fd / FO / F5 (Designer electric cooktops) Key or keyboard errors (FA, FC, FJ, FU, FL, Fb), LED test error (Fd), software error (FO), communication error (F5).
Call a technician
Wipe the controls dry, then reset the breaker. If it returns, call for service.
F01 / F02 / F03 / F04 (some Professional ranges) Commonly reported by repair references as: F01 door latch circuit fault, F02 temperature sensor fault, F03 cooling fan feedback fault, F04 meat probe shorted.
Call a technician
Reset the breaker. If the code returns, call for service.
F06 / F07 / F10 (some Professional ranges) Commonly reported by repair references as: F06 control configuration mismatch, F07 door switch fault, F10 runaway temperature.
Call a technician
For F10, turn the oven off at the breaker (and shut the gas on dual fuel models) and do not use it. For the others, reset and call if they return.

What we actually find on Viking ranges in the Denver area

The codes above come from Viking’s own documentation. This section shows what our technicians found once they opened the machine. Since 2024 we have handled 10 Viking range service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The oven repairs we do most often (all brands)

Our notes on Viking ranges are too thin to rank by brand alone, so here is what we found across all 645 oven calls in our records:

  1. Control board: 54 calls
  2. Igniter: 45 calls
  3. Bake or broil element: 26 calls
  4. Surface element or burner switch: 20 calls
  5. Wiring: 16 calls
  6. Convection fan: 15 calls
  7. Temperature sensor: 13 calls

Viking range repairs from $320. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2024–2026. Customer details removed.

Video: Viking range igniter troubleshooting

Video by Mods & Projects

What we see on Denver calls

  • Across all 645 oven calls in our records (all brands), the repairs we do most often: control board (54 calls), igniter (45) and bake or broil element (26).

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. Note the exact code or light pattern and your model number, found on the rating plate.
  2. Turn off power at the breaker for a few minutes, then restore it and retest.
  3. For latch codes, let the oven cool completely, close the door firmly, and make sure the knob is not past the Clean or Broil position.
  4. For probe errors, unplug the meat probe and check that the jack is clean and dry.
  5. On induction and electric cooktops, wipe the controls dry and keep the air inlet below the cooktop clear.
  6. If you smell gas, leave the home and call the gas utility. Never work on gas valves or burners yourself.

When to call a technician

  • The oven overheats or shows a runaway temperature fault.
  • The door stays locked after the oven has fully cooled.
  • RTD, latch or controller codes return after a breaker reset.
  • Igniters spark without lighting, or you smell gas.
  • Cooktop sensor, relay or power device codes keep returning.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

Why are the Cycle and Clean lights flashing on my Viking range?

On Viking gas self-clean ranges, the Cycle and Clean lights act as a fault display. Cycle flashing with Clean off points to the oven temperature sensor, while Clean flashing with Cycle off points to the self-clean door latch.

How do I reset a Viking oven error?

Turn off the range at the circuit breaker for a few minutes, then turn it back on. If the code or light pattern returns, the fault is still there and needs service.

What does F1 mean on a Viking oven?

On Viking VGSO gas wall ovens, F1 means a shorted temperature probe. Other Viking controls use different meanings, so check your model line.

My Viking oven door is locked after self-clean. What do I do?

Wait until the oven has cooled completely; the latch will not release while it is hot. If it stays locked when cool, or a latch error appears, call for service.

Sources: mypros.plus, mypros.plus, mypros.plus, mypros.plus, mypros.plus, manualslib.com, manualslib.com. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229
Call Now Book Online