Dryer Takes Too Long to Dry? Causes and Fixes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

Long dry times are most often caused by restricted airflow: a dirty lint screen, a clogged or crushed vent duct, or a blocked outside hood. Overloading, a washer that leaves clothes too wet, and a failing heating part are the next most common causes. A clogged vent is also a fire hazard, so clean it first.

A dryer needs both heat and airflow. When moist air cannot leave the drum, clothes stay damp no matter how hot it runs. Slow drying is one of the clearest warning signs of a lint-clogged vent, which is a leading cause of home dryer fires.

Common causes and how to fix them

1. Clogged vent duct or outside hood DIY check

Signs: Dry times creeping up over weeks, hot dryer top, hot laundry room, weak airflow at the outside hood.

Fix: Disconnect the duct and clean it end to end, and clear the outside flap. Long or roof-vented runs often need a professional vent cleaning.

2. Crushed or wrong vent material DIY check

Signs: Duct is kinked behind the dryer, or is white plastic or thin foil.

Fix: Replace with rigid or semi-rigid metal duct and keep the run as short and straight as possible.

3. Dirty lint screen DIY check

Signs: Visible lint, or a waxy film from dryer sheets that blocks air even when it looks clean.

Fix: Clean lint after every load. Wash the screen with warm soapy water and a soft brush every few months.

4. Overloading or very wet loads DIY check

Signs: Large or bulky loads, or clothes dripping when they come out of the washer.

Fix: Dry smaller loads. If the washer leaves clothes soaking wet, the washer may need repair.

5. Dirty moisture sensor DIY check

Signs: Auto-dry cycles end early and clothes are still damp.

Fix: Wipe the metal sensor bars inside the drum with rubbing alcohol on a soft cloth.

6. Weak heating (element, igniter, or gas valve coils) Technician

Signs: Some heat, but not enough. Gas models may light and then go out mid-cycle.

Fix: A technician tests the heating parts and thermostats.

7. Cycling thermostat or control issue Technician

Signs: Heat shuts off too soon and the drum runs cool.

Fix: A technician tests the thermostat and controls.

Video: why a dryer takes too long to dry

Video by RepairClinic.com

What we see on Denver calls

  • Since 2024 we have been called out for a dryer that takes too long 49 times across the Denver metro and Boulder County. The most common findings on those calls: clogged vent or lint (6 calls), thermistor or sensor (3) and drive belt (2).
  • Every number here comes from our own job records, not from the video.
  • If the checks shown in the video don’t solve it, these are the first things our technicians test.

Don’t want to do it yourself? Call 720-230-1229.

What actually caused it on our service calls

The causes above are the general list. This section shows what our technicians found on real jobs. Since 2024 we have been called out for a dryer that takes too long 49 times across the Denver metro and Boulder County. Every number below comes from our own job records.

What we found most often

  1. Clogged vent or lint: 6 calls
  2. Thermistor or sensor: 3 calls
  3. Drive belt: 2 calls
  4. Control board: 2 calls

Brands we saw with this problem

LG (10), Samsung (9), Whirlpool (4), GE (4), Kenmore (3), Maytag (2). This counts our calls only; it is not a reliability ranking.

Recent calls

  • Denver (80222), October 2026: Dryer not spinning. Repair: drive belt replaced.
  • Superior (80027), June 2026: LG dryer making noise. Diagnosis: idler pulley or drum rollers (part 4581EL2002L).
  • Commerce City (80022), January 2026: Dryer ice maker not working. Repair: thermistor or sensor replaced.
  • Longmont (80504), May 2024: LG dryer ice maker not working. Diagnosis: thermistor or sensor (part AGM30045804).

Dryer repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2024–2026. Customer details removed.

Brand by brand: what we find inside

We went back through our job notes, through October 2026, and pulled every call for this problem where the brand was written down. Technician notes are short, so the part counts below are minimums: the real numbers are higher. Part numbers are the ones our technicians actually installed or ordered on these calls.

Samsung 13 calls

Samsung: a weak or failed heating element (DC47-00019A) in Thornton and Centennial, and in Erie a thermistor, a moisture sensor and later the element. Vents come next: in Littleton the vent duct needed cleaning with special tools, and in Greenwood Village the dryer heated but did not dry, so the vent was the next step.

Parts on our tickets: DC47-00019A element, thermistor, moisture sensor.

Samsung dryer repair · Samsung dryer not heating

LG 11 calls

LG: vents and sensors. Filter and vent cleaning in Lone Tree, a clogged vent line replaced in Erie, and thermistors (AGM30045804) in Longmont and Broomfield. On another Longmont call one leg of the power supply had only about 50 volts, so the dryer could not heat properly.

Parts on our tickets: AGM30045804 thermistor, EBR85130517 control board, 4581EL2002L roller kit.

LG dryer repair · LG dryer codes

Whirlpool

Whirlpool: airflow cleaning and a new vent duct in Longmont.

Whirlpool dryer repair

Kenmore

Kenmore: a worn repair kit in Henderson: belt (661570V), bracket and drum wheels.

Parts on our tickets: 661570V belt, W10837240 bracket, 4392067 wheels.

Kenmore dryer repair

What you can safely check yourself

  1. Unplug the dryer before moving it or working behind it. On a gas dryer, do not disconnect or bend the gas line.
  2. Clean the lint screen and the lint screen housing with a vacuum crevice tool.
  3. Disconnect the vent duct and clean it with a vent brush kit, then clear the outside hood flap.
  4. Replace plastic or foil duct with metal duct, and push the dryer back without crushing it.
  5. With the dryer running, check the outside hood. You should feel strong, warm airflow.
  6. Try a medium load on a timed high-heat cycle to see if dry time improves.

When to call a technician

  • The vent run is long, goes through the roof, or you cannot reach all of it.
  • You smell burning or see scorch marks, or the dryer top gets too hot to touch.
  • Airflow is strong but the air is cool or only lukewarm.
  • Dry time stays long after cleaning the lint screen and vent.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

How long should a normal load take to dry?

A typical mixed load usually dries in about 40 to 60 minutes on a normal cycle. If you routinely need a second cycle, check airflow first.

How often should a dryer vent be cleaned?

Clean the lint screen every load and the vent duct at least once a year. Heavy use, long duct runs, or pets may call for more frequent cleaning.

Can a slow dryer cause a fire?

Yes. Lint is very flammable, and a restricted vent makes the dryer run hotter and longer. Failure to clean dryers is a leading cause of home dryer fires, so treat slow drying as a safety issue.

Does dry Colorado air mean clothes should dry faster?

Low humidity helps a little, but airflow and heat matter far more. A clogged vent will slow drying in any climate.

720-230-1229
720-230-1229
Call Now Book Online