Dryer Not Heating? Causes and Fixes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

A dryer that tumbles but stays cold usually has a blown thermal fuse, a failed heating element (electric) or igniter (gas), or a tripped breaker that cut half of the 240-volt power. A clogged vent is often the root cause, because it makes the dryer overheat and blow the fuse.

When a dryer spins but the clothes come out damp and cool, the heat source or one of its safety parts has usually failed. Electric and gas dryers share some causes and have a few of their own. Start with the simple power and airflow checks below before replacing parts.

Common causes and how to fix them

1. Blown thermal fuse Technician

Signs: Drum turns but there is no heat at all. On some models the dryer will not start.

Fix: Replace the fuse, then find out why it blew. A restricted vent is the usual reason.

2. Clogged or crushed vent DIY check

Signs: Long dry times before the heat quit, hot laundry room, little air at the outside vent hood.

Fix: Clean the lint screen, disconnect and clean the duct, and clear the outside hood.

3. Tripped breaker or blown fuse (electric) DIY check

Signs: Drum spins but no heat. Electric dryers use two 120-volt legs; losing one can leave the motor running with no heat.

Fix: Reset the double-pole breaker at the panel. If it trips again, stop and call a pro.

4. Failed heating element (electric) Technician

Signs: No heat even with full power. The coil may look broken or stretched.

Fix: A technician tests the element for continuity and replaces it if open.

5. Failed igniter, flame sensor, or gas valve coils (gas) Technician

Signs: Igniter does not glow, or glows and then goes dark without lighting. Heat may work at first, then quit as the dryer warms up.

Fix: A technician tests the igniter, flame sensor, and valve coils and replaces the failed part.

6. Gas supply turned off (gas) DIY check

Signs: No flame and no gas smell. The supply valve behind the dryer may have been bumped while moving it.

Fix: Make sure the dryer's shutoff valve handle is parallel to the gas line. Do not work on the gas line itself.

7. Bad high-limit or cycling thermostat Technician

Signs: No heat, or heat that shuts off too early or runs too hot.

Fix: A technician tests both thermostats and replaces the faulty one.

8. Control or timer fault Technician

Signs: Heat works on some cycles but not others, or the display shows an error.

Fix: A technician checks the control board or timer contacts.

Video: why a dryer stops heating

Video by RepairClinic.com

What we see on Denver calls

  • The video shows a standard top-load electric dryer, the Whirlpool-built type we service most. On our 180 no-heat calls across the Denver metro and Boulder County since 2023, the heating element was the cause far more often than anything else: 50 calls, vs 12 for the thermal fuse or thermostat.
  • On Whirlpool dryers like this one, the element we install most is (12 of our 29 Whirlpool calls). The thermistor comes next.
  • Most Kenmore dryers are Whirlpool-built and take the same element. Standard Maytag models use.
  • Badly clogged vents came up on our Whirlpool calls too. Clean the vent first, or a new element or fuse can fail again.

Don’t want to do it yourself? Call 720-230-1229.

What actually caused it on our service calls

The causes above are the general list. This section shows what our technicians found on real jobs. Since 2023 we have been called out for a dryer that won’t heat 180 times across the Denver metro and Boulder County. Every number below comes from our own job records.

What we found most often

  1. Heating element: 50 calls
  2. Thermal fuse or thermostat: 12 calls
  3. Idler pulley or drum rollers: 3 calls
  4. Drive belt: 3 calls
  5. Thermistor or sensor: 3 calls
  6. Clogged vent or lint: 2 calls
  7. Control board: 2 calls

Brands we saw with this problem

Samsung (42), Whirlpool (20), Maytag (20), LG (14), Kenmore (9), GE (5). This counts our calls only; it is not a reliability ranking.

Recent calls

  • Arvada (80005), October 2026: Dryer not heating. Repair: heating element replaced.
  • Lafayette (80026), September 2026: LG dryer not heating. Repair: thermal fuse or thermostat replaced.
  • Centennial (80111), July 2026: Samsung dryer not heating. Cause: clogged vent or lint, cleared on site.
  • Boulder (80301), July 2026: Samsung dryer not heating. Repair: heating element replaced.

Dryer repairs from $320. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Brand by brand: what we find inside

We went back through our job notes, through October 2026, and pulled every call for this problem where the brand was written down. Technician notes are short, so the part counts below are minimums: the real numbers are higher. Part numbers are the ones our technicians actually installed or ordered on these calls.

Samsung 82 calls

Samsung electric dryers lead our no-heat calls, and one part dominates: the heating element, named in 27 of 82 calls. Thermal fuses (6 calls), thermistors and the control board cover most of the rest. The element often fails because of restricted airflow, so we check the vent on the same visit.

Parts on our tickets: heating element, thermal fuses, thermistors, control board.

Samsung dryer repair · Samsung dryer codes

LG 31 calls

LG is different: the thermal fuse and thermistor come up more than the element. On gas LG dryers we have replaced the igniter, flame sensor and gas valve coils. A freshly cleaned vent does not rule out other faults: one Longmont dryer was two years old, had just had its vent cleaned and still needed thermistors and a control board.

Parts on our tickets: thermal fuse, thermistor, control board, igniters and flame sensors.

LG dryer repair · LG dryer codes

Maytag 30 calls

Maytag electric dryers mostly need a heating element (13 calls): on front-load-style models, on standard models.

Parts on our tickets: heating elements.

Maytag dryer repair

Whirlpool 29 calls

Whirlpool: heating element (12 calls), thermistors and badly clogged vents. On one call a dryer that kept tripping the breaker and did not heat needed a new element.

Parts on our tickets: heating element, thermistor, vent cleaning.

Whirlpool dryer repair

Kenmore 22 calls

Most Kenmore dryers are Whirlpool-built, so they take the same element. Gas Kenmores get the gas valve coil kit (279311).

Parts on our tickets: element, 279311 gas valve coils, thermal fuses.

Kenmore dryer repair

Electrolux

Electrolux: a heating element (5304535760) in Lyons.

Parts on our tickets: 5304535760 heating element.

Electrolux dryer repair

KitchenAid

KitchenAid: a heating element (3387747) in Boulder.

Parts on our tickets: 3387747 heating element.

Bosch

Bosch: a switch repaired in Longmont.

Bosch dryer repair

What you can safely check yourself

  1. Make sure you are not on an air-fluff or no-heat setting.
  2. Check the breaker panel and reset a tripped dryer breaker once.
  3. Unplug the dryer (and for gas models, also confirm the gas valve is open) before touching anything behind it.
  4. Clean the lint screen with warm soapy water if it looks coated from dryer sheets.
  5. Pull the dryer out, disconnect the vent duct, and clear any lint from the duct and the outside hood.
  6. Run a timed dry with a small load and check the air coming out of the outside vent. It should feel warm and strong.

When to call a technician

  • The breaker trips again after you reset it.
  • You smell gas, or the gas dryer will not light with the supply valve open.
  • There is a burning smell or scorch marks near the drum or vent.
  • The vent is clear and there is still no heat, which points to a failed electrical part.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

Why does my dryer spin but not heat?

The most common causes are a blown thermal fuse, a failed heating element or igniter, or a tripped breaker on one side of the 240-volt circuit. The motor can keep running while the heat circuit is dead.

Can a clogged vent stop a dryer from heating?

Yes. A blocked vent traps hot air, the dryer overheats, and the thermal fuse or high-limit thermostat cuts the heat to protect it. Replacing the fuse without cleaning the vent usually means it blows again.

Is it safe to keep using a dryer with no heat?

Running it on air-only will not hurt it, but find the cause soon. If heat loss followed a burning smell or very long dry times, stop using it until the vent and heating parts are checked.

How do I know if my gas dryer igniter is bad?

Watch through the small window or listen at the start of a heat cycle. If the igniter never glows, it or its wiring has likely failed. If it glows but never lights the gas, the flame sensor or valve coils are more likely.

720-230-1229
720-230-1229

Photos from our job records

Real photos our technicians took on repair calls around Denver and the Front Range. Each caption says where the job was.

Dryer repair in Denver, photo from our job records
Dryer repair in Denver
Dryer repair in Denver, photo from our job records
Dryer repair in Denver
Dryer repair in Denver, photo from our job records
Dryer repair in Denver
Dryer repair in Denver, photo from our job records
Dryer repair in Denver
Call Now Book Online