Standing water in a dishwasher is usually caused by a clogged filter or sump, a kinked or clogged drain hose, a blocked garbage disposal or air gap, or a failed drain pump. Clean the filter and run the disposal first; those two steps fix many drain problems.
A dishwasher pumps water out through a filter, a drain pump, and a hose that usually connects to the disposal or sink drain. A blockage anywhere along that path leaves water in the tub. Work from the inside out: filter, then hose and disposal, then pump.
Common causes and how to fix them
1. Clogged filter or sump DIY check
Signs: Water sits in the bottom, with food debris, seeds, or glass around the filter.
Fix: Remove and clean the filter under running water with a soft brush, and wipe out the sump area.
2. Garbage disposal clogged or knockout plug left in DIY check
Signs: Water will not drain, especially after a new disposal was installed.
Fix: Run the disposal. On a newly installed disposal, the drain knockout plug may still be in place and must be removed.
3. Kinked or clogged drain hose DIY check
Signs: Slow or no draining; hose is pinched behind the dishwasher or under the sink.
Fix: Straighten the hose and make sure it has a high loop or air gap. A technician can replace a clogged hose.
4. Clogged air gap DIY check
Signs: Water spurts from the small cap by the faucet during drain.
Fix: Remove the air gap cover and clear debris.
5. Blocked or failed drain pump Technician
Signs: Humming with no draining, or no sound during drain. Debris may be stuck in the pump impeller.
Fix: A technician clears or replaces the drain pump.
6. Stuck check valve or drain valve Technician
Signs: Water drains back in, or drains only partly.
Fix: A technician frees or replaces the valve.
7. Control or cycle not finished DIY check
Signs: Cycle was interrupted or canceled, leaving water behind.
Fix: Run a drain or cancel/drain cycle per the owner's manual.
Video: why a dishwasher won’t drain
Video by RepairClinic.com
What we see on Denver calls
- Since 2024 we have been called out for a dishwasher that won’t drain 68 times across the Denver metro and Boulder County. The most common findings on those calls: drain pump (15 calls), clogged filter or drain (3) and circulation pump or wash motor (3).
- Every number here comes from our own job records, not from the video.
- If the checks shown in the video don’t solve it, these are the first things our technicians test.
Don’t want to do it yourself? Call 720-230-1229.
What actually caused it on our service calls
The causes above are the general list. This section shows what our technicians found on real jobs. Since 2024 we have been called out for a dishwasher that won’t drain 68 times across the Denver metro and Boulder County. Every number below comes from our own job records.
What we found most often
- Drain pump: 15 calls
- Clogged filter or drain: 3 calls
- Circulation pump or wash motor: 3 calls
Brands we saw with this problem
GE (13), Bosch (12), Whirlpool (5), KitchenAid (3), Kenmore (2), Samsung (2). This counts our calls only; it is not a reliability ranking.
Recent calls
- Lafayette (80026), October 2026: Maytag dishwasher not draining. Repair: drain pump replaced.
- Lakewood (80215), January 2026: Whirlpool dishwasher not draining. Cause: clogged filter or drain, cleared on site.
- Broomfield (80020), March 2025: GE dishwasher not draining. Repair: circulation pump or wash motor replaced.
- Centennial (80112), January 2025: GE dishwasher not draining. Repair: drain pump replaced.
Dishwasher repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.
Source: The Appliance Team service records, 2024–2026. Customer details removed.
Brand by brand: what we find inside
We went back through our job notes, through October 2026, and pulled every call for this problem where the brand was written down. Technician notes are short, so the part counts below are minimums: the real numbers are higher. Part numbers are the ones our technicians actually installed or ordered on these calls.
Bosch 14 calls
Bosch is the brand where cleaning works most often: six of fourteen calls were cleared by cleaning the drain pump, circulation pump, spray arms or drain hose. A blocked end of the drain hose, a drain hose connector (12012913) and the drain pump (00631200) cover the rest. E24 and E25 are the drain codes.
Before you call: clean the filter cylinder and run the garbage disposal. That cleared E24 on one Westminster call before we even arrived.
Parts on our tickets: 00631200 drain pump, 12012913 drain hose connector.
GE 11 calls
GE is the opposite: the drain pump fails outright, sometimes together with the check valve and drain hose (one Littleton call took).
Parts on our tickets: drain pumps, check valves, drain hoses.
Whirlpool 8 calls
Whirlpool: filter and drain hose cleaning. On one Westminster dishwasher water kept collecting in the tub after a few days of standing; the fix was a proper high loop on the drain hose, not a part.
Parts on our tickets: drain hose, high loop, filter cleaning.
KitchenAid 6 calls
KitchenAid shows F9E1 for drain problems. Half the calls needed a drain pump; the other half were cleared by cleaning the filter (RIF filter).
Parts on our tickets: drain pumps, filter.
Samsung
Samsung: drain pumps in Louisville and Arvada, and a drain filter cleaning in Denver.
Parts on our tickets: drain pump.
LG
LG: a drain pump in Lafayette, and standing water removed from the base in Longmont.
Parts on our tickets: drain pump.
Frigidaire
Frigidaire: a drain hose cleaned in Commerce City and a lower spray arm in Westminster.
Parts on our tickets: 5304517203 spray arm.
Maytag
Maytag: a drain pump in Lafayette.
Parts on our tickets: drain pump.
JennAir
JennAir: a drain pump in Greenwood Village.
Parts on our tickets: drain pump.
What you can safely check yourself
- Turn off power to the dishwasher at the breaker before reaching into the tub or sump.
- Remove standing water with a cup and towels so you can see the filter.
- Remove the filter, rinse it, and scrub it with a soft brush and warm soapy water.
- Run the garbage disposal with cold water for 30 seconds.
- Check under the sink for a kinked or crushed drain hose.
- Clean the air gap cap at the sink if you have one, then restore power and run a rinse or drain cycle.
When to call a technician
- The pump hums but water does not move, or you hear no pump at all.
- Water stays after cleaning the filter, disposal, hose, and air gap.
- Water is leaking onto the floor while draining.
- You see an error code related to draining.
How to prevent this
Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:
Frequently asked questions
Is it normal to have some water in the bottom of a dishwasher?
A small amount near the filter or sump is normal on many models. Standing water that covers the tub floor is not.
Can I use drain cleaner in a dishwasher?
No. Chemical drain cleaners can damage the pump, seals, and hoses. Clean the filter by hand and clear the disposal instead.
Why won't my dishwasher drain after a new disposal was installed?
The disposal's dishwasher inlet has a knockout plug from the factory. If it was not removed during installation, the dishwasher cannot drain into it.
How often should I clean the dishwasher filter?
Many manufacturers suggest about once a month, or more often if you do not rinse dishes. A clogged filter causes both draining and cleaning problems.



