On a Fisher & Paykel DishDrawer, A and U codes are alerts you can usually fix: A1 or U1 means no water, A3 means the drawer cannot drain, A6 or U6 points to the spray arm or low water pressure, A7 means excess foam, and U2 means something is too tall for the lid. F and E codes are faults: F1 (flood switch) means turn off water and power and call for service, and F2-F9 cover the motor, heater, temperature sensor, lid and electronics.
DishDrawer dishwashers use different code styles by generation. Older and classic models show U codes, most models show A codes for alerts and F codes for faults, and some integrated and designer models show E codes or flash the wash program lights. The F1-F9 meanings come from the DS605 user manual and Sears PartsDirect; the A, U and E codes come from repair references, since meanings vary by model. Turn off power, and water for leak checks, before any hands-on work.
Fisher & Paykel DishDrawer error codes and what they mean
| Code | What it means | What to try |
|---|---|---|
A1 / U1 |
No water, or not enough water coming in. | Make sure the water supply valve is on and the inlet hose is not kinked. Check that the spray arm sits on its hub and spins freely. If the drawer is full of water, empty it by hand. |
A3 |
The drawer cannot drain. | Clean the filter and check the drain hose for kinks or a blocked connection at the sink drain or disposer. |
A6 / U6 |
Spray arm loose or not clipped in, or low water pressure, sometimes with excess foam. | Reseat the spray arm and make sure it turns freely. Use only dishwasher detergent. |
A7 |
Foam recovery: the drawer detected excess suds and started a recovery routine. | Use the correct dishwasher detergent in a smaller amount. Never use hand dish soap. |
A09 |
The sanitize cycle did not reach the required temperature (DD*C models). | Run the cycle again. Run the kitchen tap hot before starting. |
A10 |
Water not received or detected. | Check the tap, water pressure, and inlet hose for kinks or a loose connection. |
A20 |
Drain fault: water remains above the filter plate after rinse. | Clean the filter and check the drain hose and outlet for kinks or blockages. |
U2 |
Loading problem: the lid cannot seal (older models). | Remove or lay down any items taller than the drawer. |
U4 |
A fault in the other drawer is stopping this drawer (double models). | Check the other drawer for a code and deal with that first. |
F1 / E1 / F30 |
Flood switch activated: water detected in the base. E1 can also be triggered by excess foam. Call a technician |
Turn off the water and power to the DishDrawer and call for service. |
F2 / E2 / F2X |
Motor problem. On some models E2 is a rotor fault caused by debris or broken glass. Call a technician |
Turn off power. Check the filter area for glass or debris. If the code returns, call for service. |
F3 / E3 / F3X |
Temperature sensor fault. Incoming water that is too hot can trigger it. Call a technician |
Make sure the water entering the drawer is below 149 degrees (65 C); a tempering valve may be needed. If it returns, call for service. |
F4 / E4 / F4X |
Water temperature not rising: faulty temperature sensor or heating element. Call a technician |
Call for service. |
F5 / F6 / E5 |
Lid fault (lid motor or lid mechanism). | Remove tall items, turn power off and back on; the fault may reset. If it persists, call for service. |
F7 |
Lid fault on DS605 models. On some newer models F7X or E7 is listed as a fill valve or detergent dispensing fault. Call a technician |
Check that the water supply is on, then call for service if it returns. |
E6 / F6X |
Drying fan or component failure (newer models). Call a technician |
Turn power off and on. If it returns, call for service. |
F8 / E8 / F8X |
Electrical problem or electronics fault (motor controller on some models). Call a technician |
Turn off the power supply to the DishDrawer and call for service. |
F9 / E9 / F9X / F90 |
Electronic control (wash controller) malfunction. Call a technician |
Turn power off for a minute and back on. If it returns, call for service. |
FC / EC / FCX |
Communication fault between the two drawers on double models. Call a technician |
Turn power off and on. If it returns, call for service. |
F40 / F50 / FA0 |
Electronics or power supply error (newer models). Call a technician |
Turn power off and on. If it persists, call for service. |
FC0 |
Motor fault (newer models). Call a technician |
Turn power off, wait, and turn it on. If it persists, turn off water and power and call for service. |
A60 / AD0 |
Water temperature error (A60) or door lock signal error (AD0) on newer models. Call a technician |
Turn power off and on. If it persists, call for service. |
What we find on Fisher & Paykel dishwashers and similar dishwashers in the Denver area
We see fewer Fisher & Paykel dishwashers than the big-volume brands: 4 service calls in our records since 2023. The parts that fail are much the same across brands, so here is what we found on all 702 dishwasher calls in our records since 2023.
The dishwasher repairs we do most often (all brands)
- Circulation pump or wash motor: 51 calls
- Control board: 35 calls
- Drain pump: 34 calls
- Water inlet valve: 13 calls
- Clogged filter or drain: 13 calls
- Door latch or seal: 12 calls
- Heating element: 11 calls
Dishwasher repairs from $220. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.
Source: The Appliance Team service records, 2023–2026. Customer details removed.
Video: Fisher & Paykel dishwasher error codes
Video by Viktor Villanyi
What we see on Denver calls
- An error code points to the system that reported the fault, not always to the part that failed.
- Across all 702 dishwasher calls in our records (all brands), the repairs we do most often: circulation pump or wash motor (51 calls), control board (35) and drain pump (34).
Don’t want to do it yourself? Call 720-230-1229.
What you can safely check yourself
- Turn off power to the DishDrawer at the breaker before any hands-on check.
- Remove and rinse the filter; look for broken glass or food around the drain area.
- Check that the spray arm is clipped on and spins freely.
- Make sure the water valve is open and the inlet and drain hoses are not kinked.
- Keep items lower than the drawer height so the lid can seal.
- Use dishwasher detergent only, and use less if you see foam.
When to call a technician
- F1, E1 or F30 appears, or there is water under the drawer.
- Motor, heater, sensor or electronics codes return after a power reset.
- The drawer still will not drain after cleaning the filter.
- The lid will not close or open with nothing in the way.
- The drawer trips the breaker or smells hot.
How to prevent this
Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:
Frequently asked questions
How do I reset a Fisher & Paykel DishDrawer?
Turn off the power at the breaker or switch for about a minute, then turn it back on. A reset can clear a one-time glitch, but if the code returns the cause is still there.
What does A3 mean on a DishDrawer?
A3 means the drawer cannot drain. Clean the filter and check the drain hose for kinks or a blocked connection at the sink or disposer.
What does F1 mean on a Fisher & Paykel dishwasher?
F1 means the flood switch was activated because water was found in the base. Turn off the water and power to the drawer and call for service.
What does U2 mean on a DishDrawer?
On older models, U2 means the lid cannot seal, usually because a dish or utensil is sticking up above the drawer. Rearrange the load and restart.
Sources: manualslib.com, searspartsdirect.com, deadshort.com.au. Codes and meanings can vary by model; check your owner's manual.