Electrolux Dishwasher Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

Most Electrolux dishwasher codes start with i (or E on some models): i10 means low water, i20, i40 or iF0 mean a drain or filter problem, i30 means water in the base pan (leak or overflow), and i50, i60 and iC0 point to the motor, heater or control. Clean the filters, check the drain hose and water supply, and use only dishwasher detergent. If i50, i60 or iC0 returns after a power reset, call a technician.

Electrolux dishwashers show a short code on the display, and models without a display may beep or flash a light the same number of times as the code (for example, 3 beeps for i30). Electrolux and Frigidaire dishwashers share the same code system on most US models. This list combines Electrolux support pages from the US and other countries with Sears parts documentation and repair references, so a few codes apply only to some models. Turn off power at the breaker before any hands-on check.

Electrolux Dishwasher error codes and what they mean

Code What it means What to try
i10 / E10 (1 beep or flash) Water level too low: the dishwasher did not fill enough. Make sure the water shutoff under the sink is fully open and the supply line is not pinched. Low household water pressure can also cause it.
i11 / AL5 / C1 On some models (mainly outside the US): water inlet problem. Check the water supply valve and inlet hose for kinks. If the code returns with good water flow, the inlet valve needs service.
i20 / E20 (2 beeps or flashes) Drain problem: the dishwasher did not empty in the expected time. Clean both filters. Check the drain hose for kinks, clear the air gap if you have one, and confirm the disposer knockout plug was removed on new installs.
i23 / C2 / F2 / AL6 On some models (mainly outside the US): draining problem. Use the same steps as i20: clean the filters and check the drain hose and disposer connection.
i30 / E30 (3 beeps or flashes) Leak or overflow detected in the base pan. The anti-flood system is on.
Call a technician
Turn off power and water. Check the inlet valve connection for drips and make sure the dishwasher is level. Use only dishwasher detergent; suds can trigger it. If it returns, request service.
i40 / E40 / iF0 / EF0 / iFo / iF1 Restricted drain line, clogged filters or a water level (pressure sensor) problem. Some models also show i43 or i44 for pressure sensor faults. Clean the filters and check the drain hose. If the code returns with a clear drain path, the pressure sensor needs service.
i50 / E50 Wash motor or drain pump issue.
Call a technician
Press Cancel or turn off the breaker for 5 minutes. Check that nothing is stuck in the filter area. If the code persists, request service.
i60 / E60 / i61 / i69 / i6C Water heating system issue. Dishes may come out cold or wet.
Call a technician
Turn off the breaker for 5 minutes and restart. Run the kitchen tap until hot before starting a cycle. If the code persists, request service.
iC0 / EC0 Electronic control system issue.
Call a technician
Press Cancel or turn off the breaker for 5 minutes. If the code persists, request service.
CLOSE / CL The door is open or not latched. Close the door firmly until it latches. Check that racks or dishes are not stopping it from closing.
PF Power failure: power was interrupted during a cycle. Press Start to resume, or Cancel and start a new cycle.
LO / rA / RE / RF Reported on Electrolux/Frigidaire-platform models: rinse aid is low (LO), or the rinse aid sensor or switch has a fault (rA, RE, RF). Refill the rinse aid dispenser. If a sensor code stays after refilling and a power reset, request service; the dishwasher still washes.
Er-01 Older Electrolux models with Er codes: water leak detected.
Call a technician
Turn off power and water, look for the leak under the tub, and call for service if you find one.
Er-02 Older models: thermistor or turbidity sensor failure.
Call a technician
Turn off power for 5 minutes and restart. If it returns, the sensor needs service.
Er-03 Older models: wash motor failure.
Call a technician
Check the filter and sump for debris such as glass or seeds. If clear and the code returns, the motor needs service.
Er-04 / Er-05 / Er-06 Older models: upper fan or vent failure (Er-04, Er-05) or lower fan failure (Er-06).
Call a technician
Turn off power for 5 minutes and restart. If the code returns, the fan or vent needs service.
Er-07 / Er-11 / Er-12 Older models: drain valve failure (Er-07, Er-11) or drain valve position error (Er-12).
Call a technician
Clean the filters and check the drain hose. If the code returns, the drain valve or control needs service.
Er-08 / Er-09 / Er-10 / Er-13 Older models: user interface switch failure (Er-08), communication failure between the interface and control board (Er-09), control board relay failure (Er-10) or control board failure (Er-13).
Call a technician
Turn off power for 5 minutes and restart. If the code returns, request service.

What we find on Electrolux dishwashers and similar dishwashers in the Denver area

We see fewer Electrolux dishwashers than the big-volume brands: only a handful of calls. The parts that fail are much the same across brands, so here is what we found on all 702 dishwasher calls in our records since 2023.

The dishwasher repairs we do most often (all brands)

  1. Circulation pump or wash motor: 51 calls
  2. Control board: 35 calls
  3. Drain pump: 34 calls
  4. Water inlet valve: 13 calls
  5. Clogged filter or drain: 13 calls
  6. Door latch or seal: 12 calls
  7. Heating element: 11 calls

Recent dishwasher calls

  • Erie (80516), October 2026: GE dishwasher not heating. Repair: heating element replaced (WD21X22830).
  • Longmont (80504), October 2026: Dishwasher stopping mid-cycle. Repair: drain pump replaced (WD19X25461).
  • Arvada (80002), October 2026: Dishwasher leaking. Repair: water inlet valve replaced (DD82-01383A).
  • Boulder (80304), September 2026: Dishwasher leaking. Repair: circulation pump or wash motor replaced (W10155344).

Dishwasher repairs from $220. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Electrolux dishwasher not draining

Video by ElectroluxUS

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • Across all 702 dishwasher calls in our records (all brands), the repairs we do most often: circulation pump or wash motor (51 calls), control board (35) and drain pump (34).

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. Turn off power at the breaker (or unplug) before any hands-on check.
  2. Remove and rinse both filters in the tub bottom.
  3. Check the drain hose for kinks and clear the air gap if you have one.
  4. Confirm the water valve under the sink is fully open.
  5. Use only automatic dishwasher detergent and keep the rinse aid filled.
  6. Make sure the dishwasher is level and the door latches firmly.

When to call a technician

  • i50, i60 or iC0 returns after a 5-minute power reset.
  • The dishwasher still will not drain with clean filters and a clear hose.
  • i30 keeps returning or you see water on the floor.
  • Water keeps entering with the dishwasher off.
  • You smell burning or see damage near the control panel.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

How do I reset an Electrolux dishwasher?

Press Cancel, or turn off the breaker for 5 minutes, then restore power and start a short cycle. If the same code returns, the cause still needs attention.

What does i20 mean on an Electrolux dishwasher?

The dishwasher did not drain in time. Clean both filters, check the drain hose for kinks, and make sure the disposer knockout plug was removed if it is newly installed.

What does i30 mean on an Electrolux dishwasher?

Water reached the base pan, so the leak protection turned on. Turn off power and water, check for leaks and oversudsing, and call for service if it returns.

My Electrolux dishwasher beeps 3 times. What does that mean?

On models without a full display, the number of beeps or flashes matches the code. Three beeps or flashes points to i30, a leak or overflow in the base.

Sources: partstown.com, searspartsdirect.com, partstown.com, appliancepartspros.com. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229
Call Now Book Online