Fisher & Paykel Washer Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

Fisher & Paykel top-load washers (SmartDrive, AquaSmart) report faults as numbers, often with beeps. Drain codes such as 37, 114 and 245-253 and fill codes such as 21, 26, 27, 49, 50 and 246 are the ones owners can check first, by clearing the drain hose and opening the taps. Motor control, display, lid lock and sensor codes usually need a technician.

Fisher & Paykel washers show faults differently by model. Top loaders with a display show a fault number; older SmartDrive models without a display signal faults with beeps and flashing lights, and retry for up to about 8 minutes before stopping and beeping continuously. The numbered codes below come from Sears PartsDirect and the SmartDrive service manual; check your model, since not every code applies to every washer. Unplug the washer before any hands-on check.

Fisher & Paykel Washer error codes and what they mean

Code What it means What to try
21 / 26 / 27 / 49 / 50 / 246 Water inlet (fill) valve problem. Make sure both taps are fully open and the fill hoses are not kinked. Turn off the taps, remove the hoses at the washer, and clean the inlet screens. If the code returns, the valve or its wiring needs service.
37 / 114 / 245 / 247 / 248 / 249 / 250 / 253 Water not draining. Check the drain hose for kinks and make sure the standpipe or laundry sink drain is not clogged. Remove small items that may be blocking the pump. If it still will not drain, call for service.
38 / 39 Water level pressure tube (air tube) fault: the tube is off, severed or kinked.
Call a technician
Call for service; the tube is inside the cabinet.
58 / 64 / 68 Water level pressure sensor fault. The sensor is part of the motor control module.
Call a technician
Unplug for 5 seconds and restart. If it returns, call for service.
10 / 41 / 237 Water temperature sensor (thermistor) fault.
Call a technician
Unplug and restart. If it returns, call for service.
234 / 235 / 238 / 239 Lid lock fault: the lock did not activate or is jammed.
Call a technician
Make sure nothing is caught in the lid and it closes fully. Unplug and restart. If it returns, call for service.
136 / 137 Motor not running or motor stall.
Call a technician
Unplug and try turning the basket by hand. If it is jammed by an item, call for service to clear it; if it turns freely, the motor or control needs service.
40 / 47 / 56 / 160 Spin basket not engaging or disengaging from the clutch.
Call a technician
Unplug and restart with a smaller, evenly spread load. If it returns, call for service.
43 Out-of-balance switch fault: the switch reads permanently on or is disconnected.
Call a technician
Redistribute the load and restart. If it returns with a balanced load, call for service.
1 / 57 / 60 / 107 / 108 / 112 / 133 Motor control module fault (on some models, code 1 is a memory write error).
Call a technician
Unplug for 5 seconds and restart. If it returns, call for service.
220-226 / 230 / 232 / 233 / 236 / 243 / 252 / 254 Motor control module fault.
Call a technician
Unplug for 5 seconds and restart. If it returns, call for service.
45 / 46 / 103 / 104 / 105 / 106 Display module fault or communication error between the display and the motor control module.
Call a technician
Unplug for 5 seconds and restart. If it returns, call for service.
241 Display module or motor control module fault.
Call a technician
Unplug and restart. If it returns, call for service.
127 Machine set-up error: the display module does not match the model, size or phase, usually after a part replacement.
Call a technician
Call for service.
132 Single current trip in the motor circuit.
Call a technician
Unplug and restart. If it returns, call for service.
Short beeps every 5 seconds, Rinse or Spin light flashing Out of balance: the washer stopped and could not correct the load during spin. Open the lid, spread the load evenly, or choose a higher water level, then restart.
Continuous beeping with a fault shown A fault persisted after the washer retried for up to about 8 minutes. Turn the washer off at the wall, wait 5 seconds, turn it on and retry. Note the code if it returns.
Err 16 / Err 19 / Err 38 (some newer models) Commonly reported by repair references: Err 16 water not draining in time, Err 19 not filling to level in time, Err 38 lid lock not engaging. Check the drain hose, open the taps and clean the inlet screens, and make sure the lid closes fully. Call for service if the code returns.

What we find on Fisher & Paykel washers and similar washers in the Denver area

We see fewer Fisher & Paykel washers than the big-volume brands: 1 service call in our records since 2023. The parts that fail are much the same across brands, so here is what we found on all 1238 washer calls in our records since 2023.

The washer repairs we do most often (all brands)

  1. Control or display board: 108 calls
  2. Drain pump: 74 calls
  3. Shock absorbers or suspension: 57 calls
  4. Water inlet valve: 41 calls
  5. Door or lid lock: 28 calls
  6. Door boot seal: 27 calls
  7. Drive belt or coupler: 23 calls

Recent washer calls

  • Denver (80204), October 2026: GE washer not spinning. Diagnosis: drive belt or coupler (part WH08X10050).
  • Longmont (80503), October 2026: Maytag washer not draining. Repair: drain pump replaced (W10237499).
  • Lakewood (80227), October 2026: Whirlpool washer door or lid problem. Repair: pressure or water-level sensor replaced (W11608056).
  • Berthoud (80513), October 2026: Washer not starting. Diagnosis: drain pump.

Washer repairs from $240. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Fisher & Paykel washer drain pump repair

Video by Parts Dr

What we see on Denver calls

  • The video shows a drain pump repair. It is the #2 washer repair on our calls (all brands).
  • Across all 1238 washer calls in our records (all brands), the repairs we do most often: control or display board (108 calls), drain pump (74) and shock absorbers or suspension (57).

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. Unplug the washer before any hands-on check.
  2. Make sure both taps are fully open and the fill hoses are not kinked.
  3. With the taps off, clean the screens where the fill hoses connect to the washer.
  4. Check the drain hose for kinks and make sure the standpipe is not clogged.
  5. Spread the load evenly and do not overload; choose a higher water level for bulky items.
  6. Reset by turning the washer off at the wall for 5 seconds, then retry.

When to call a technician

  • Motor control, display or sensor codes return after a reset.
  • The washer will not drain with a clear hose and standpipe.
  • The lid lock code returns with the lid closed properly.
  • The basket will not turn, or turns but will not spin.
  • Water leaks from under the washer.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

How do I reset a Fisher & Paykel washer?

Turn the washer off at the wall, wait about 5 seconds, turn it back on and restart. If the same code returns, the problem still needs attention.

Why is my Fisher & Paykel washer beeping every few seconds?

Short beeps every 5 seconds with the Rinse or Spin light flashing usually mean the load is out of balance. Spread the clothes evenly and restart.

What does code 49 mean on a Fisher & Paykel washer?

Code 49 is one of the water inlet valve codes. Check that the taps are on and the inlet screens are clean; if it returns, the valve needs service.

Do all Fisher & Paykel washers use the same codes?

No. Codes vary by generation and model, so note your model number and the exact code before you troubleshoot or call.

Sources: searspartsdirect.com, manualslib.com, removeandreplace.com, ozappliancespares.com.au. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229
Call Now Book Online