Bosch Dishwasher Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

The most common Bosch dishwasher codes point to drain problems (E24 drain hose or filter, E25 drain pump blocked, E22 filter blocked), fill problems (E16, E17, E18), or a leak (E15, water in the base). You can often clear these by cleaning the filter and pump cover, straightening hoses and checking the water supply. Heater, relay, motor and sensor codes such as E01-E09 need a technician.

Bosch dishwashers show an E code when a cycle cannot finish. Newer models may show a four-digit version of the same fault, such as E6103 for E24. To reset, Bosch recommends turning off power at the breaker for 30 seconds. If the code comes back, the cause is still there. Turn off power before any hands-on check. This list combines the manufacturer's own documentation with codes reported by established repair-parts references (such as Sears PartsDirect, PartSelect and repair technicians' guides); those are marked "commonly reported" or "on some models".

Bosch Dishwasher error codes and what they mean

Code What it means What to try
E24 / E6103 Not draining: the drain hose is kinked or blocked, or the filter is clogged. Check the drain hose under the sink for kinks. Clean the filters. If the hose connects to a new garbage disposer, make sure the knockout plug was removed.
E25 / E6102 Drain pump is blocked, or the pump cover is loose or missing. With power off, remove the filters and scoop out standing water. Remove the pump cover under the filter, clear glass or debris, and snap the cover back in place.
E22 / E9240 Filter is blocked. Remove the filter, wash it under running water with mild soap and a soft brush, and reinstall it.
E23 / E6101 Drain pump is blocked, clogged or faulty.
Call a technician
Clear the pump area as for E25. If the code returns, the pump needs service.
E15 / E3100 Water detected in the base; leak protection is activated.
Call a technician
Turn off the water supply to the dishwasher and request service. Oversudsing from dish soap can also trigger it.
E16 / E17 / E3300 / E3400 Water cannot enter the dishwasher. Make sure the water valve is open and the inlet hose is not kinked or damaged.
E18 / E3200 Water level too low, or water not pumped correctly. Check the inlet hose and make sure the water supply is fully on with good flow.
E14 / E3000 Flow meter failure or fill system problem.
Call a technician
Request service.
E09 / E20 / E2030 / E6001 Heat pump internal heater fault.
Call a technician
Turn off the breaker for 30 seconds, then back on. If the code returns, request service.
E21 / E6002 Heat pump (circulation pump) is blocked.
Call a technician
Reset at the breaker. If it returns, request service.
E01 / E0100 Heat pump motor circuit fault at the main control board.
Call a technician
Reset at the breaker. If it returns, request service.
E02 / E03 / E0103 / E0107 Main control board relay fault.
Call a technician
Reset at the breaker. If it returns, request service.
E04 / E0105 Faulty heater electronics found in self-test.
Call a technician
Request service.
E05 / E0106 Wash arm diverter circuit fault.
Call a technician
Reset at the breaker. If it returns, request service.
E06 / E8000 Door sensor circuit fault.
Call a technician
Reset at the breaker. If it returns, request service.
E07 / E10 / E2120 / E2130 CrystalDry (zeolite) drying system fault: fan motor (E07) or chamber heater (E10).
Call a technician
Reset at the breaker. If it returns, request service.
E12 / E2060 Limescale buildup in the heat pump. Descale with a dishwasher descaler. If your model has a water softener, keep it filled with softening salt. Denver's hard water makes scale more likely.
E19 / E6900 Detergent dispenser circuit fault.
Call a technician
Reset at the breaker. If it returns, request service.
E27 / E9001 House power supply voltage is too low.
Call a technician
Reset at the breaker. If it keeps happening, have an electrician check the incoming voltage.
H01, H02 ... Delay start is set. Not an error. Press + or – until h:00 shows to cancel the delay.
E0 / E00 Shown in diagnostic mode when no faults are saved. Not a fault. No action needed.
E08 Commonly reported: water level too low at the heating element, or a sudden loss of water during the cycle.
Call a technician
Check that the water supply is fully open and the filter is clean. If the code returns, call a technician.
E11 Commonly reported: temperature sensor (NTC thermistor) fault.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
E13 Commonly reported: water too hot (above about 167°F / 75°C).
Call a technician
Check whether the dishwasher is connected to a very hot supply or the water heater is set too high. If it continues, call a technician.
E26 Depending on model: water switch or regulator problem, or a diverter motor fault (commonly reported).
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
E28 Depending on model: flow sensor fault, or a turbidity (aqua) sensor fault (commonly reported).
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
E29 Depending on source: water detected in the base, or a power supply voltage problem (commonly reported).
Call a technician
Turn off power and check under the dishwasher for water. If you find none and the code returns, call a technician.
E30 Commonly reported as a power supply voltage problem.
Call a technician
Reset at the breaker. If it recurs, have an electrician check the incoming voltage.
E31 Commonly reported on CrystalDry (zeolite) models: drying system error.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
E0110 Bosch: a failure causing electronics miscommunication.
Call a technician
Call for service.
E6160 Bosch: PowerControl (controlled lower spray arm) reference position not found.
Call a technician
Call for service.
E200 Listed by Bosch on its US error code page without a published meaning. Control-detected fault; the manufacturer lists the code without a public meaning. Reset by unplugging for 5 minutes; if it returns, call a technician.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
Red light on floor blinking On models with InfoLight: a steady red light means the dishwasher is running; a blinking light means there is an issue. Check the display for a code. Turn off power at the breaker for 30 seconds and restart.
3 beeps / 5 beeps Commonly reported: 3 beeps means water is pooling in the base; 5 beeps means water in the base has triggered the sensor.
Call a technician
Turn off power and the water supply. Check the filter, hoses and door seal for leaks. Call a technician if it repeats.

What we actually find on Bosch dishwashers in the Denver area

The codes above come from Bosch’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 72 Bosch dishwasher service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The dishwasher repairs we do most often (all brands)

Our notes on Bosch dishwashers are too thin to rank by brand alone, so here is what we found across all 702 dishwasher calls in our records:

  1. Circulation pump or wash motor: 51 calls
  2. Control board: 35 calls
  3. Drain pump: 34 calls
  4. Water inlet valve: 13 calls
  5. Clogged filter or drain: 13 calls
  6. Door latch or seal: 12 calls
  7. Heating element: 11 calls

Recent Bosch dishwasher calls

  • Littleton (80122), November 2025: Bosch dishwasher not starting. Diagnosis: drain pump.
  • Westminster (80031), August 2025: Bosch dishwasher not draining. Cause: clogged filter or drain, cleared on site.
  • Boulder (80304), December 2024: Bosch dishwasher not starting. Repair: float switch or leak sensor replaced (00165301).
  • Boulder (80301), November 2024: Bosch dishwasher not starting. Repair: float switch or leak sensor replaced (00622036).

Bosch dishwasher repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Bosch dishwasher error codes

Video by Ken Long

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • Across all 702 dishwasher calls in our records (all brands), the repairs we do most often: circulation pump or wash motor (51 calls), control board (35) and drain pump (34).
  • Recent call: Boulder (80304), December 2024: Bosch dishwasher not starting. Repair: float switch or leak sensor replaced (00165301).

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. Turn off power at the breaker before any hands-on check.
  2. Remove and clean the filters in the tub floor.
  3. Remove the pump cover under the filter and clear glass, seeds or labels, then snap it back.
  4. Check the drain hose under the sink for kinks and remove a new disposer's knockout plug.
  5. Make sure the water valve is open and the inlet hose is not kinked.
  6. Use only dishwasher detergent, never hand dish soap.
  7. Reset by turning the breaker off for 30 seconds.

When to call a technician

  • E15 appears or water is in the base or on the floor.
  • Heater, relay, motor or sensor codes return after a breaker reset.
  • The dishwasher still will not drain after cleaning the filter and pump cover.
  • The dishwasher will not fill even with the water supply on.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

How do I reset a Bosch dishwasher error code?

Turn the dishwasher off at the circuit breaker for 30 seconds, then turn it back on. If the code returns, the underlying problem still needs attention.

What does E24 mean on a Bosch dishwasher?

E24 means the dishwasher cannot drain. The usual causes are a kinked drain hose, a clogged filter, or a disposer knockout plug that was never removed.

What does E15 mean on a Bosch dishwasher?

E15 means water was detected in the base and leak protection stopped the dishwasher. Turn off the water supply and have a technician find the leak.

What is the difference between E25 and E24?

E24 usually points to the drain hose or filter, while E25 points to the drain pump itself being blocked or its cover being loose. Both are often cleared by cleaning the filter and pump area.

Sources: bosch-home.com, bosch-home.com, sparesonweb.com, removeandreplace.com. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229
Call Now Book Online