Fisher & Paykel Refrigerator Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

Fisher & Paykel ActiveSmart refrigerators report faults as a number, shown with a spanner icon on LCD models or as flashing LEDs on models with only a temperature bar. Common ones are sensor faults (codes 3-10), defrost failure (code 2) and fan faults (15-18). Ice maker codes are often fixable by clearing ice; sensor, fan, defrost and control codes need a technician.

Fisher & Paykel ActiveSmart refrigerators have used several control generations, and the same number can mean different things on older and newer models. On LCD models, opening the fresh food door makes the unit beep the code number and show it beside a spanner icon; models with only an LED temperature bar show the code in binary by flashing LEDs. The codes below come from repair references that list the ActiveSmart service codes. Unplug the refrigerator before any hands-on check.

Fisher & Paykel Refrigerator error codes and what they mean

Code What it means What to try
1 / F1 (Stage 4.2 ActiveSmart) The control module failed its power-up self test.
Call a technician
Turn off power for 5 minutes, then back on. If it returns, call for service.
2 / F2 (Stage 4.2 ActiveSmart) Defrost failure: defrost cycles were aborted, often from a failed defrost heater or thermal fuse.
Call a technician
Check for heavy frost on the back freezer wall and call for service.
3 / 4 All temperature sensors read open (3) or shorted (4), often a loose sensor plug or moisture in a connector.
Call a technician
Turn off power for 5 minutes and restart. If it returns, call for service.
5 / 6 Freezer sensor open (5) or shorted (6).
Call a technician
Reset power. If it returns, call for service.
7 / 8 Evaporator (defrost) sensor open (7) or shorted (8).
Call a technician
Reset power. If it returns, call for service.
9 / 10 Fresh food sensor open (9) or shorted (10).
Call a technician
Reset power. If it returns, call for service.
11 / 12 / 13 / 14 Low ambient heater faults: heater and fans out of range together (11, 12), heater open (13) or heater over-current (14). Most relevant in cold garages.
Call a technician
Make sure the refrigerator is not in a space that gets very cold. Call for service if it returns.
15 / 16 Fridge fan drawing too little (15) or too much (16) current.
Call a technician
Make sure food is not blocking the air vents inside, then call for service.
17 / 18 Freezer fan fault. Code 17 is one of the most reported ActiveSmart codes.
Call a technician
Check that ice or food is not blocking the freezer fan area, then call for service.
20 / 21 Ice chute flapper heater fault (ice and water models).
Call a technician
Reset power. If it returns, call for service.
22 / 23 / 24 / 25 Water tank sensor (22, 23) or ice tray sensor (24, 25) out of range. Cooling is not affected.
Call a technician
Reset power. If it returns, call for service.
26 / 27 Ice maker harvest motor fault. Remove any block of ice jammed in the ice maker or bin, then reset power.
28 / 29 / 40 / 41 Ice maker water inlet valve fault.
Call a technician
Make sure the water supply to the refrigerator is on. If it returns, call for service.
42 / 43 Ice maker fill tube blocked or frozen. Turn off the ice maker and let the fill tube thaw. If it keeps freezing, call for service.
30 / 31 Display or display harness fault. Cooling usually continues.
Call a technician
Reset power. If it returns, call for service.
49 Communication error between control boards.
Call a technician
Turn off power for 5 minutes and restart. If it returns, call for service.
1-13 (older Stage 4.1 ActiveSmart) Older controllers number codes differently: 1 FC sensor low, 2-3 evaporator sensor, 4-5 PC sensor, 6 defrost fault, 7 control self test, 9 low ambient heater, 10-11 PC fan current, 12-13 FC fan current.
Call a technician
Note the code and your model number and call for service.
F1 / F2 / F3 / F4 / F6 (RX628 and RX611 side-by-side) Sensor faults on these models: F1 and F2 fresh food sensor, F3 room temperature sensor, F4 freezer sensor, F6 defrost sensor.
Call a technician
Reset power. If it returns, call for service.
E0 / E1 / E2 / Ed (RX628 and RX611 side-by-side) E0 communication error between boards, E1 freezer fan not running, E2 evaporator fan fault, Ed defrost system failure.
Call a technician
Reset power. If it returns, call for service.

What we find on Fisher & Paykel refrigerators and similar refrigerators in the Denver area

We see fewer Fisher & Paykel refrigerators than the big-volume brands: only a handful of calls. The parts that fail are much the same across brands, so here is what we found on all 1685 refrigerator calls in our records since 2023.

The refrigerator repairs we do most often (all brands)

  1. Compressor or sealed system: 167 calls
  2. Evaporator or condenser fan: 121 calls
  3. Control or inverter board: 120 calls
  4. Ice maker: 109 calls
  5. Defrost system: 66 calls
  6. Thermistor or sensor: 37 calls
  7. Water inlet valve: 32 calls

Recent refrigerator calls

Refrigerator repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Fisher & Paykel refrigerator error codes

Video by Paul P

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • Across all 1685 refrigerator calls in our records (all brands), the repairs we do most often: compressor or sealed system (167 calls), evaporator or condenser fan (121) and control or inverter board (120).

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. Write down the code number, or which LEDs are flashing, before resetting.
  2. Check that the doors close fully and nothing blocks the inside air vents.
  3. Clear any ice jams from the ice maker and bin.
  4. Make sure the water supply to the refrigerator is on for ice and water models.
  5. Reset by switching off power at the wall or breaker for 5 minutes.
  6. Do not keep resetting a code that returns; that does not fix the cause.

When to call a technician

  • Sensor, fan, defrost or control codes return after a reset.
  • Frost builds up on the back freezer wall.
  • The fresh food section is above 41 degrees or the freezer is soft.
  • The fans are silent or noisy with the compressor running.
  • Ice maker valve codes return with the water supply on.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

How do I read the error code on a Fisher & Paykel refrigerator?

On LCD models, open the fresh food door; the unit beeps the code number and shows it next to a spanner icon. On models with only an LED temperature bar, add up the position values of the flashing LEDs.

What does code 17 mean on a Fisher & Paykel ActiveSmart?

On Stage 4.2 ActiveSmart models, code 17 is a freezer fan fault. Check that ice is not blocking the fan, then call for service.

How do I reset a Fisher & Paykel refrigerator?

Switch it off at the wall or breaker for about 5 minutes, then turn it back on. If the code returns, the fault is still there.

Why do different sources give different meanings for the same code?

Fisher & Paykel changed the numbering between control generations. Always match the code to your model number before acting on it.

Sources: ozappliancespares.com.au. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229
Call Now Book Online