Whirlpool dishwashers show F#E# codes on a display, or flash the Clean light in two groups (for example 9 flashes, pause, 1 flash = F9E1). The most common are F9E1 (slow drain), F8E4 (water in the drip tray), F6E3 (too many suds), F6E4 (float switch) and H2O (no water detected), which you can often fix by cleaning the filter, clearing the drain hose and using only dishwasher detergent. Control, heater, motor and sensor codes usually need a technician.
Some Whirlpool code meanings changed between older and newer dishwasher platforms, so the same code can point to different parts. Where that happens, this page lists both. On models without a display, count the first set of Clean light flashes (the F number), then the second set after a short pause (the E number). Disconnect power before any hands-on check, and turn off the water supply if water is leaking. This list combines the manufacturer's own documentation with codes reported by established repair-parts references (such as Sears PartsDirect, PartSelect and repair technicians' guides); those are marked "commonly reported" or "on some models".
Whirlpool Dishwasher error codes and what they mean
| Code | What it means | What to try |
|---|---|---|
F9E1 (9 flashes, 1 flash) |
On current models: long drain, the dishwasher is not draining fast enough. On some older models: the diverter disc position cannot be detected. | Remove and rinse the filter. Check the drain hose under the sink for kinks or clogs. If it drains into a disposer, run the disposer and make sure the knockout plug was removed on a new install. Clear the air gap cap if you have one. Use only automatic dishwasher detergent. |
F9E2 |
On current models: drain motor error. On some older models: the diverter motor is stuck on. Call a technician |
Do the same drain checks as F9E1, then cut power for 30 seconds and restart. If it returns, the drain pump or control needs service. |
F8E4 (8 flashes, 4 flashes) |
Water detected in the drip tray under the tub. The dishwasher drains and stops. Call a technician |
Turn off the water to the dishwasher. Check the water supply connection for leaks and look for suds. Press Cancel to silence the alarm. If water keeps reaching the tray, a technician should find the leak. |
F8E5 (8 flashes, 5 flashes) |
Fill valve stuck open: water keeps coming in. Call a technician |
Turn off the water supply under the sink. Press Cancel once to silence the alarm and keep the door closed. If you cannot shut off the water, cut power to the dishwasher. The inlet valve needs service. |
F8E1 / F8E2 (8 flashes, 1 or 2 flashes) |
Older models: slow drain (F8E1) or a drain pump electrical problem (F8E2). Call a technician |
Clean the filter and check the drain hose and disposer as for F9E1. If the drain path is clear, the pump or its wiring needs service. |
F6E3 |
Too many suds (on older models, also air in the pump or low water). | Scoop out suds and run a rinse with no dishes. Use only automatic dishwasher detergent, never hand dish soap, and make sure the rinse aid cap is in place. |
F6E4 |
Float (overfill) switch error. | Make sure nothing is under or pressing on the float in the front of the tub and that the dishwasher is level. Cut power for 30 seconds and restart. If it returns, the float switch or inlet valve needs service. |
H2O |
No water detected. | Make sure the water supply valve under the sink is fully open and the supply line is not kinked. |
F6E1 (6 flashes, 1 flash) |
On current models: user interface or main control error. On some older models: the dishwasher will not fill. Call a technician |
Cut power for 30 seconds and restart. On older models, also confirm the water is on and nothing is lifting the float. If it returns, request service. |
F6E2 / F6E6 |
Older models: water inlet valve failure (F6E2), or incoming water is too cold (F6E6). Call a technician |
For F6E6, run the kitchen tap until hot before starting a cycle and check that the water heater is set to about 120°F. For F6E2, request service. |
F7E2 |
On current models: wash motor error. On some older models: the heating element will not shut off. Call a technician |
Cut power for 30 seconds and restart. If it returns, request service. |
F7E1 / F4E2 / F4E3 |
Heating problem: the heating element is not working (F7E1 on older models) or a heating system error (F4E2/F4E3 on current models). Call a technician |
Cut power for 30 seconds and restart. If dishes stay wet or the code returns, a technician should test the heater and its wiring. |
F4E4 |
Older models: communication error with the circulation (wash) pump motor. Call a technician |
Cut power for a few minutes and restart. If it returns, request service. |
F3E1 / F3E2 / F3E3 |
Temperature sensor (thermistor) or OWI (optical water indicator) sensor problem. On some models, F3E3 can also mean dirty water is flowing back through the drain hose. Call a technician |
Cut power for 30 seconds and restart. Make sure the drain hose has a high loop or air gap so water cannot flow back. If the code returns, request service. |
F5E1 / F5E2 |
Door switch problem, or the control did not detect the door opening between cycles. | Open and fully close the door, then start the cycle within a few seconds. If it still fails after a power reset, the door latch assembly needs service. |
F2E1 (2 flashes, 1 flash) |
Stuck key or console error. | Wipe the control panel dry and press each button. Cut power for 30 seconds and restart. If it returns, the control panel needs service. |
F1E1 / F1E2 / F2E2 |
Control module or main control communication error. Call a technician |
Unplug the dishwasher or turn off its breaker for 30 seconds, then restore power. If the code returns, request service. |
FAE4 / F10E4 (10 flashes, 4 flashes) |
Diverter valve error (the part that sends water to the upper or lower spray arm). Call a technician |
Cut power for 30 seconds and restart. If it returns, request service. |
F9E3 / F9E4 |
Older models: the diverter disc is missing (F9E3) or the lower spray arm is blocked or not turning (F9E4). Call a technician |
Make sure nothing is blocking the lower spray arm and that it spins freely by hand. If the code returns, request service. |
F6E7 (6 flashes, 7 flashes) |
Flow meter (water flow sensor) disconnected or damaged, on models that have one. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
F6E8 (6 flashes, 8 flashes) |
Water softener models only: problem with the softener regeneration valve. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
F8E3 (8 flashes, 3 flashes) |
Older models: the drain pump is stuck on. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
FAE5 / F10E5 (10 flashes, 5 flashes) |
Possible diverter leak. Call a technician |
Turn off power and check under the dishwasher for water; make sure the water connections are tight. Press Cancel twice and start a new cycle. If the code returns, call a technician. |
F4E3 (some Global HE models) |
On some older Global HE models, F4E3 means a communication error between the control board and the circulation (wash) pump motor. On current models it is a heating system error (see F4E2/F4E3 above). Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
FAE1 / FAE2 / FAE3 (10 flashes, 1 to 3 flashes) |
Detergent dispenser failure (FAE1), vent wax motor problem (FAE2), or drying fan failure (FAE3). Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
What we actually find on Whirlpool dishwashers in the Denver area
The codes above come from Whirlpool’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 57 Whirlpool dishwasher service calls across the Denver metro and Boulder County. Every number here comes from our own job records.
The dishwasher repairs we do most often (all brands)
Our notes on Whirlpool dishwashers are too thin to rank by brand alone, so here is what we found across all 702 dishwasher calls in our records:
- Circulation pump or wash motor: 51 calls
- Control board: 35 calls
- Drain pump: 34 calls
- Water inlet valve: 13 calls
- Clogged filter or drain: 13 calls
- Door latch or seal: 12 calls
- Heating element: 11 calls
Recent Whirlpool dishwasher calls
- Lakewood (80215), January 2026: Whirlpool dishwasher not draining. Cause: clogged filter or drain, cleared on site.
- Longmont (80504), December 2025: Whirlpool dishwasher not starting. Repair: control board replaced.
- Longmont (80504), May 2025: Whirlpool dishwasher not filling. Diagnosis: circulation pump or wash motor.
- Denver (80209), February 2025: Whirlpool dishwasher leaking. Repair: drain pump replaced.
Whirlpool dishwasher repairs from $220. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.
Source: The Appliance Team service records, 2023–2026. Customer details removed.
Video: Whirlpool dishwasher error codes
Video by Parts Dr
What we see on Denver calls
- An error code points to the system that reported the fault, not always to the part that failed.
- Across all 702 dishwasher calls in our records (all brands), the repairs we do most often: circulation pump or wash motor (51 calls), control board (35) and drain pump (34).
- Recent call: Longmont (80504), December 2025: Whirlpool dishwasher not starting. Repair: control board replaced.
Don’t want to do it yourself? Call 720-230-1229.
What you can safely check yourself
- Unplug the dishwasher or turn off its breaker before any hands-on check.
- Remove the filter at the bottom of the tub and rinse it under running water.
- Check the drain hose under the sink for kinks, run the disposer, and clear the air gap if you have one.
- Make sure the water supply valve is fully open and the supply line is not kinked.
- Use only automatic dishwasher detergent; hand dish soap causes suds and drain codes. Denver's hard water may call for rinse aid.
- For most other codes, cut power for 30 seconds, then restart the cycle once.
When to call a technician
- Water is in the drip tray (F8E4) or keeps filling (F8E5).
- A control, heater, motor, diverter or sensor code returns after a power reset.
- The dishwasher will not drain even with a clean filter and clear hose.
- Dishes come out cold or wet every cycle.
- You see water on the floor or smell burning.
How to prevent this
Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:
Frequently asked questions
How do I read Whirlpool dishwasher blinking light codes?
Count the first group of Clean light flashes, which is the F number, then the second group after a short pause, which is the E number. For example, 6 flashes, a pause, then 4 flashes is F6E4. The pattern repeats after a longer pause.
How do I reset a Whirlpool dishwasher error code?
Unplug the dishwasher or turn off its breaker for 30 seconds, then restore power. If the code returns, the cause is still there.
What does F9E1 mean on a Whirlpool dishwasher?
On current models, F9E1 means the dishwasher is draining too slowly. Clean the filter, check the drain hose and disposer, and clear the air gap. On some older models the same code pointed to a diverter problem instead.
Sources: producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, searspartsdirect.com, searspartsdirect.com, nelihome.com, producthelp.kitchenaid.com. Codes and meanings can vary by model; check your owner's manual.



