Miele Dishwasher Fault Codes (F Codes)

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

The Miele dishwasher codes you are most likely to see are F11 (water not draining), F12, F13, F15 or F173 (water inlet blocked), F14, F69 or F78 (circulation pump stuck), and F70 (the Waterproof system found a leak). Drain and inlet codes can often be cleared by cleaning the filters, drain pump and inlet filter. F70 and the technical faults Miele marks as not owner-fixable need a technician.

Miele dishwashers show faults as an F followed by a number, and some models flash the inlet/drain or other indicator lights instead. Miele's own help pages say which faults you can fix and which need a technician; this list follows them. Before any hands-on check, turn the dishwasher off and unplug it or switch off its breaker, and close the water faucet for inlet checks.

Miele Dishwasher Fault Codes (F Codes) error codes and what they mean

Code What it means What to try
F11 Water is not draining. On G 1xxx-G 6xxx models, usually a blocked drain pump or a non-return valve that is not seated. On G 7xxx and 2019+ G 5xxx Discovery models, a blocked pump or a drain pump cover that is not clicked in. Unplug the dishwasher, remove the filters, bail out the water, rinse the non-return valve or pump cover, and clear the pump impeller (turn it by hand). Reseat everything flush and run a cycle.
F12 / F13 / F15 / F173 The water inlet is blocked or restricted. Turn the faucet fully on. With power off and the faucet closed, unscrew the inlet hose and rinse the inlet filter. Straighten the hose. If water pressure is below 7.25 psi, contact a plumber.
F14 Circulation problem: the circulation pump is stuck (common after long idle periods) or a pump pressure or heating level switch fault. Remove the lower spray arm and filters, pour 1 liter of hot water (under 165 degrees) with a few drops of rinse aid into the tub, wait 5 minutes, reassemble and restart. Repeat 2-3 times. If it persists, call for service.
F69 / F78 Circulation pump blocked, often because it dried out and stuck after a long break or at first use. Use the same hot water and rinse aid soak as for F14, then switch off, wait a few seconds, switch on and restart. If it returns, call for service.
F70 The Waterproof system has reacted to a leak. The program is canceled and the drain pump runs.
Call a technician
Turn off the water faucet, switch off and unplug the dishwasher, wait for the pump to stop, and call for service.
F1 / F2 Water/heating temperature sensor short circuit (F1) or open circuit (F2).
Call a technician
No owner fix. Call for service.
F18 / F19 Water intake valve faulty (F18) or flow meter faulty (F19).
Call a technician
No owner fix. Call for service.
F24 / F25 / F26 Heating relay contact fault (F24), desired temperature fault (F25), or boiling protection triggered (F26).
Call a technician
No owner fix. Call for service.
F33 / F36 Door lock not opening (F33) or door lock switch faulty (F36).
Call a technician
No owner fix. Call for service.
F38 / F40 / F42 / F47 Electronic faults; F42 is an electrical frequency registration fault.
Call a technician
Switch off for a few seconds and back on. If the code returns, call for service.
F51 / F53 Pump pressure level switch fault (F51) or speed sensor fault (F53).
Call a technician
No owner fix. Call for service.
F52 Too much detergent or rinse aid caused excess foam and interrupted the wash. Set the program selector to Stop/Finish, switch off and back on. Use less detergent and check the rinse aid setting.
F63 Water path control unit fault.
Call a technician
No owner fix. Call for service.
F67 / F68 / F79 Circulation pump fault or failure.
Call a technician
No owner fix. Call for service.
F84 Water intake fault (technical).
Call a technician
No owner fix. Call for service.
F85 / F87 / F172 / F179 / F594 / F595 Technical or electronic faults that Miele says owners cannot fix.
Call a technician
Switch off and back on once. If the code returns, call for service.
F86 The salt container flap is open. Close the salt reservoir flap. If it persists, call for service.
F88 / F91 Turbidity sensor fault (F88) or load recognition inactive (F91).
Call a technician
No owner fix. Call for service.
F170 Out of rinse aid. Refill the rinse aid and press OK.
F171 Low on softener salt. Refill the salt after the cycle ends and press OK. Denver's hard water uses salt faster.
F177 Filter cleaning reminder after a set number of cycles. Clean the filter combination as your manual shows, then press OK.
F600 AutoDos detergent outlet is blocked. The dishwasher drains and cancels the wash. Clean the lower spray arm jets and the AutoDos housing and holder, dry everything, reinsert a full PowerDisk, and close the lid tightly.
F601 AutoDos automatic dispensing fault. Check the PowerDisk and holder are seated correctly and clean the system. If it returns, switch AutoDos off and add detergent by hand until it is serviced.
F607 The lower spray arm is blocked, so AutoDos shuts off during the cycle. Make sure the lower spray arm spins freely, clean its jets, and keep tall items in the lower basket away from it.
Inlet/drain light flashing A fault occurred while filling or draining; water may be left in the tub. On models without F codes this is the main fault signal. Do the F11 drain checks and the F12 inlet checks. If the Waterproof system has activated, turn off the faucet, unplug, and call for service.
All indicator lights flashing Limescale, grease or other soil has built up inside the dishwasher. Clean the filter combination, non-return valve, drain pump and spray arms. If the lights keep flashing, call for service.

What we actually find on Miele dishwashers in the Denver area

The codes above come from Miele’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 12 Miele dishwasher service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

Code Our calls What we found
F24 2 Most often: control board. Also seen: heating element.

The dishwasher repairs we do most often (all brands)

Our notes on Miele dishwashers are too thin to rank by brand alone, so here is what we found across all 702 dishwasher calls in our records:

  1. Circulation pump or wash motor: 51 calls
  2. Control board: 35 calls
  3. Drain pump: 34 calls
  4. Water inlet valve: 13 calls
  5. Clogged filter or drain: 13 calls
  6. Door latch or seal: 12 calls
  7. Heating element: 11 calls

Recent Miele dishwasher calls

  • Boulder (80304), August 2026: Miele dishwasher showing F24. Repair: control board replaced.
  • Boulder (80304), August 2026: Miele dishwasher showing F24. Repair: heating element replaced.
  • Boulder (80304), May 2024: Miele dishwasher leaking. Diagnosis: door latch or seal.

Dishwasher repairs from $220. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Miele dishwasher error codes

Video by Lester B

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • Across all 702 dishwasher calls in our records (all brands), the repairs we do most often: circulation pump or wash motor (51 calls), control board (35) and drain pump (34).
  • Recent call: Boulder (80304), August 2026: Miele dishwasher showing F24. Repair: control board replaced.

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. Switch off and unplug the dishwasher, or turn off its breaker, before any check.
  2. Remove and rinse the filter combination; check for glass splinters around the drain pump.
  3. Clean the non-return valve or drain pump cover and make sure it sits flush and clicks in.
  4. Close the faucet, unscrew the inlet hose and rinse the small inlet filter.
  5. Straighten any kinks in the inlet and drain hoses.
  6. For a stuck circulation pump, use Miele's soak: 1 liter of hot water with 3-5 drops of rinse aid for 5 minutes.
  7. Keep salt and rinse aid filled and use the recommended detergent amount.

When to call a technician

  • F70 or the Waterproof system activates.
  • Any code Miele lists as a technical fault, such as F1, F2, F18, F24, F26, F33 or F79.
  • F11 or F14 returns after cleaning and the hot water soak.
  • The door will not open or unlock.
  • The dishwasher trips the breaker or smells hot.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

What does F11 mean on a Miele dishwasher?

F11 means water is not draining. The usual causes are a blocked drain pump or a non-return valve or pump cover that is not seated; cleaning and reseating it fixes most cases.

What does F70 mean on a Miele dishwasher?

F70 means the Waterproof system detected a leak and stopped the program. Turn off the water, unplug the dishwasher, and call for service.

How do I fix F14 or F78 on a Miele?

These usually mean the circulation pump has dried out and stuck. Pour 1 liter of hot water with a few drops of rinse aid into the tub, wait 5 minutes, and restart; repeat 2-3 times before calling for service.

How do I reset a Miele dishwasher fault?

Switch the dishwasher off, wait a few seconds, switch it on and restart the program. If the code returns, the fault is still there.

Sources: mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229
Call Now Book Online