GE Dishwasher Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

Most GE dishwasher codes point to a drain problem (C1, C2, C3, FTD/F56), a fill or float problem (C4, C5, H2O), water that is too cool (C6), or a blocked detergent cup (C8, Cup Open). You can often clear these by cleaning the air gap and filter, running the disposer, freeing the float, or running hot water at the sink first. C7, PrS and LEAK DETECTED usually need a technician.

GE dishwashers show a short code when a cycle cannot finish normally. Not every code appears on every model, so check your owner's manual if a code does not match. Turning power off at the breaker for a minute or two clears many codes, but if the cause is still there the code will come back. Before any hands-on check, turn off power at the breaker. This list combines the manufacturer's own documentation with codes reported by established repair-parts references (such as Sears PartsDirect, PartSelect and repair technicians' guides); those are marked "commonly reported" or "on some models".

GE Dishwasher error codes and what they mean

Code What it means What to try
C1 Pump-out during drain took longer than 2 minutes. Clean the air gap on the sink, check the drain hose for kinks, and run the garbage disposer to clear the connection. If it persists, request service.
C2 Total pump-out time ran longer than 7 minutes. Press Reset to stop the beeping. Check the air gap, drain hose and disposer as for C1.
C3 Dishwasher will not drain.
Call a technician
Turn power off at the breaker for about 30 seconds, then back on. Clean the filter and check the drain path. If it continues, the drain pump likely needs service.
C4 The dishwasher filled twice after a power failure. The float may be stuck, or the sump or drain may be clogged. Touch Start, then cancel/reset. Tap the float cover to free it, and check the sump at the back of the tub floor for debris.
C5 Pump-out time was too short. Make sure the water supply is on, tap the float cover to free it, and rerun the cycle.
C6 Incoming water is too cool (below about 120°F). Run the kitchen faucet until the water is hot before starting, avoid other hot water use during the cycle, and check the water heater setting.
C7 Water temperature sensor circuit failed.
Call a technician
Turn power off at the breaker for about 30 seconds, then back on. If C7 returns, request service.
C8 The detergent cup is blocked and cannot open fully. Move any dish or utensil blocking the cup, close and latch the door, and wait 30 seconds.
H2O Low water. Check that the water supply valve is open and the inlet hose is not kinked. If it shows only during the 1-Hour Wash, other cycles can still run, but schedule service.
FTD / F56 Failure to drain. Check the drain hose, air gap and disposer. Clean the filter. If water still stands in the tub, request service.
PF A power failure occurred during the cycle. Select the cycle and options again, then press Start.
Cup Open The detergent cup is not closed, so the cycle will not start. Add detergent and latch the cup closed. Pressing Start again overrides the message.
LEAK DETECTED A possible leak was detected (models with leak detection). The cycle is canceled.
Call a technician
Turn off the water and power to the dishwasher and request service.
999 Varies by model. On Floor Protect with Alert models, the dishwasher will not start. On other models, the control needs a reset. On Floor Protect models, request service. On others, turn power off at the breaker for a minute, then back on.
PrS Pressure sensor is sending an invalid signal. The cycle will not start or will cancel.
Call a technician
Usually a wiring harness or sensor problem. Request service.
1H, 2H ... (number + H) Delay Start is set. Not an error. Wait for the delay to end, or cancel Delay Start.
F2 / F3 / F5 Newer models with F codes: communication failure between the user interface and the control board (F2), inverter board configuration error (F3), or inverter board communication failure (F5).
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
F16 Newer models: water temperature too high.
Call a technician
Make sure the dishwasher is not connected to an unusually hot supply. If the code repeats, call a technician.
F33 Newer models: door switch failure.
Call a technician
Close the door firmly. If the code returns, call a technician.
F34 Newer models: water leak detected.
Call a technician
Turn off power and the water supply, and look for water under the dishwasher. Call a technician.
F35 Newer models: diverter feedback error.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
F48 / F49 / F52 Newer models: turbidity (water cleanliness) sensor failure.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
F50 / F51 Newer models: temperature sensor failure.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
F64 / F144 / F145 / F149 Newer models: inverter (pump control) board problems: inverter error (F64), inverter board failure (F144), no AC power to the inverter board (F145), or an inverter wiring harness failure (F149).
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
F65 / F80 / F96 Newer models: no water detected, by the inverter board (F65) or the turbidity sensor (F80, F96). Make sure the water valve under the sink is fully open and the supply line is not kinked. If the code returns, call a technician.
F97 / F99 Newer models: heater failure (F97), or the minimum wash temperature was not reached (F99).
Call a technician
Run hot water at the sink before starting. If the code returns, call a technician.
F98 Newer models: not draining. Clean the filter, check the drain hose and air gap, and run the disposer. If it repeats, call a technician.
F112 Newer models: a keypad button is stuck.
Call a technician
Press each button firmly, then turn power off at the breaker for a minute. If it returns, call a technician.
F128 Newer models: rinse aid is low. Refill the rinse aid dispenser.
F146 / F147 Newer models: circulation (wash) pump failure (F146) or drain pump failure (F147).
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
F148 Newer models: the thermal fuse in the wiring harness has blown.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.

What we actually find on GE dishwashers in the Denver area

The codes above come from GE’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 103 GE dishwasher service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The GE dishwasher repairs we do most often

Across all 103 GE dishwasher calls, with or without a code on the display:

  1. Control board: 14 calls
  2. Circulation pump or wash motor: 8 calls
  3. Drain pump: 7 calls
  4. Heating element: 6 calls
  5. Water inlet valve: 3 calls
  6. Pressure or turbidity sensor: 2 calls

Recent GE dishwasher calls

  • Erie (80516), October 2026: GE dishwasher not heating. Repair: heating element replaced (WD21X22830).
  • Longmont (80504), October 2026: GE dishwasher not draining. Repair: drain pump replaced (WD19X25461).
  • Boulder (80304), March 2026: GE dishwasher leaking. Repair: water inlet valve replaced (WD15X10014).
  • Littleton (80123), September 2025: GE dishwasher not draining. Repair: drain pump replaced (WD01X10175).

GE dishwasher repairs from $240. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: GE dishwasher error codes

Video by Parts Dr

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • The GE dishwasher repairs we do most often across the Denver metro and Boulder County: control board (14 calls), circulation pump or wash motor (8) and drain pump (7).
  • Recent call: Erie (80516), October 2026: GE dishwasher not heating. Repair: heating element replaced (WD21X22830).

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. Turn off power at the breaker before any hands-on check.
  2. Clean the filter in the tub floor and remove food or glass from the sump area.
  3. Clean the air gap on the sink and run the garbage disposer before starting a cycle.
  4. Check the drain hose under the sink for kinks.
  5. Run the kitchen faucet until hot before starting, so the first fill is hot.
  6. Load dishes so nothing blocks the detergent cup or spray arms.
  7. For other codes, cut power for 30 seconds to 2 minutes, then restart once.

When to call a technician

  • Water stands in the tub after cleaning the filter, air gap and drain hose.
  • LEAK DETECTED appears or you see water on the floor.
  • C7 or PrS returns after a power reset.
  • The dishwasher keeps filling, or will not fill even with the water on.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

How do I reset my GE dishwasher?

Turn the dishwasher off at the circuit breaker for a minute or two, then turn it back on. This clears many codes, but if the cause is still there, the code returns.

What does C6 mean on a GE dishwasher?

The incoming water is cooler than about 120°F. Run the kitchen faucet until the water is hot before starting, and avoid showers or laundry during the cycle.

Why does my GE dishwasher show C1 or C3?

Both point to slow or failed draining. Clean the filter, air gap and disposer connection first. If it still will not drain, the drain pump may need service.

What does H2O mean on a GE dishwasher?

The dishwasher sensed low water. Check that the water valve is open and the inlet hose is not kinked. If those are fine, a technician should check the inlet valve and sensors.

Sources: products.geappliances.com, searspartsdirect.com, searspartsdirect.com, partselect.com. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229
Call Now Book Online