Kenmore Dishwasher Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

To read a Kenmore dishwasher code you first need to know who manufactured it. The first three digits of the model number tell you: 665 is Whirlpool, 587 is Frigidaire, 630 is Bosch, 363 is GE, and some Elite 722-series units use LG-style codes. Across all of them, the codes we see most are drain codes (F8E1, F9E1, i20, E24, C1 to C3, OE), fill codes (F6E1, i10, IE) and base-pan leak codes (i30, E15, AE). Start with the filter and the drain hose; heater, motor and board codes are technician work.

Kenmore never built its own dishwashers. Sears bought them from several manufacturers, and each one kept its own code language, so an “E24” on one Kenmore and an “F9E1” on another can describe the same clogged drain. The model label sits on the side edge of the door or the tub opening; match the digits before the dot to a table below. Whirlpool-built 665 models without a screen blink the Clean light instead of showing letters. Switch off the breaker before reaching into the tub or under the sink. Sources include Sears parts documentation, the original makers’ support pages and established repair references.

Kenmore dishwasher codes by manufacturer

665 models (built by Whirlpool)

No display? Count the Clean light: a burst of blinks for F, a pause, a burst for E. Seven then one is F7E1. Watch the pattern twice before you trust the count.

Code Meaning for this Kenmore family What we suggest
F1E1, F1E2 (1-1, 1-2) Board relay stuck (E1) or board memory fault (E2).
Technician
Breaker off five minutes, one more cycle. Comes back? Book a repair.
F2E1, F2E2 (2-1, 2-2) Stuck key (E1), or panel and board not communicating (E2); the console lights may flicker quickly.
Technician
Press each key firmly; a repeat means the panel or board.
F3E1, F3E2 (3-1, 3-2) Thermistor or OWI sensor open or shorted.
Technician
One reset, then sensor and wiring checks.
F3E3 (3-3) Optical water sensor could not calibrate, or dirty water is backing in through a failed drain check valve.
Technician
Give the drain hose a high loop or an air gap.
F4E1, F4E2, F4E4 Board cannot communicate with the wash pump motor.
Technician
One reset; then the motor, harness or board.
F5E1, F5E2, steady Clean light Door switch fault (E1) or no door opening seen between cycles (E2). Open and shut the door, start again and close it within a few seconds of Start.
F6E1, F6E2 No fill (E1) or failed inlet valve (E2). Open the hot valve under the sink fully; make sure the float is not stuck up.
F6E3 Suds or air in the pump. Dishwasher detergent only; run an empty rinse.
F6E4 Overfill float switch open. Free the float in the front corner. Water entering with the unit off: shut the valve and call.
F6E6, F6E7, F6E8 Water too cold (E6), flow meter (E7), softener valve on softener models (E8). For E6, run the tap hot first and set the heater near 120 °F. Others: reset once.
F7E1, F7E2, 7 Clean blinks Heater not working (E1) or not switching off (E2).
Technician
Heater, thermistor and board get tested.
F8E1, F8E2, F8E4 Slow drain (E1), drain pump electrical fault (E2), drain pump motor failed (E4). Clean the filter, unkink the hose, make sure the disposer knockout is removed.
F9E1 to F9E4 Diverter: position unknown (E1), motor stuck on (E2), disc missing (E3), lower arm blocked (E4).
Technician
Make sure the lower arm spins freely.
FAE1, FAE2, FAE3 (10-x) Detergent dispenser (E1), vent wax motor (E2), drying fan (E3).
Technician
Keep tall items clear of the dispenser lid.
FCE1, FCE2, FCE3, FCE5 (12-x) Wi-Fi module, router link, internet or antenna. Washing is unaffected. Reconnect to the router per your manual.
Start/Resume or Sanitized blinking Cycle paused by a door opening or power loss; or sanitize temperature not reached. Close the door and press Start/Resume. For Sanitized, check that the sink gets to about 120 °F.

587 models (built by Frigidaire)

Code Meaning for this Kenmore family What we suggest
i10 Not enough water, almost always a supply issue. Open the shutoff and check for a pinched line.
i20, i40, iF0 (2 blinks) Drain restricted or filters clogged. Clean both filters, check the hose and the disposer knockout.
i30 (3 blinks) Leak or overflow in the base pan.
Technician
Kill power and water, look for a dripping supply fitting, level the unit.
i50, i60, iC0 Wash or drain motor (i50), heating (i60), electronic control (iC0).
Technician
Cancel, or breaker off five minutes.

630 models (built by Bosch)

Code Meaning for this Kenmore family What we suggest
E24, E25 Drain hose kinked or filter clogged (E24); pump blocked or its cover loose (E25). Power off, clean the filter, clear the hose, remove debris from the pump cover.
E15 Water in the base; leak protection active.
Technician
Shut off water and power. Excess suds can also trigger it.
E16, E17 Fill problem.
Technician
Valve fully open; repeated E17 usually means the inlet valve.
E09, E01, E04 Heating or heat pump circuit faults.
Technician
Breaker off five minutes, one more cycle. Comes back? Book a repair.

363 models (built by GE)

Code Meaning for this Kenmore family What we suggest
C1, C2, C3 Drain took over 2 minutes (C1), over 7 minutes (C2), or no drain at all (C3). Filter, hose and sink drain first; then the pump.
C4, C5 Overfill (C4) or underfill (C5). Free the float and open the supply fully.
C6, C7 Water too cool (C6) or temperature sensor bad (C7). Run the tap hot first; C7 after a reset means the sensor.
C8, Cup Open, PF Dispenser lid blocked (C8) or open (Cup Open); power failure (PF). Close the cup and keep tall pans away from it; restart after PF.

722-series Elite (LG-style codes)

Code Meaning for this Kenmore family What we suggest
IE, OE Will not fill (IE) or will not drain (OE). IE: valve and inlet hose. OE: filter, hose, air gap, disposer.
AE, E1, FE Leak sensed (AE, E1) or overflow (FE).
Technician
Water and power off, find the leak. FE with water still entering means the inlet valve.
tE, HE, LE, nE Thermistor (tE), heating (HE), circulation pump locked (LE), diverter motor (nE).
Technician
Clear the filter and sump, reset once.

What we actually find on Kenmore dishwashers in the Denver area

The codes above come from Kenmore’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 11 Kenmore dishwasher service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The dishwasher repairs we do most often (all brands)

Our notes on Kenmore dishwashers are too thin to rank by brand alone, so here is what we found across all 702 dishwasher calls in our records:

  1. Circulation pump or wash motor: 51 calls
  2. Control board: 35 calls
  3. Drain pump: 34 calls
  4. Water inlet valve: 13 calls
  5. Clogged filter or drain: 13 calls
  6. Door latch or seal: 12 calls
  7. Heating element: 11 calls

Recent Kenmore dishwasher calls

  • Longmont (80504), March 2025: Kenmore dishwasher not starting. Repair: circulation pump or wash motor replaced.
  • Boulder (80305), February 2024: Kenmore dishwasher not starting. Repair: control board replaced (W10518394).

Kenmore dishwasher repairs from $160. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Kenmore dishwasher error codes

Video by Parts Dr

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • Across all 702 dishwasher calls in our records (all brands), the repairs we do most often: circulation pump or wash motor (51 calls), control board (35) and drain pump (34).
  • Recent call: Longmont (80504), March 2025: Kenmore dishwasher not starting. Repair: circulation pump or wash motor replaced.

Don’t want to do it yourself? Call 720-230-1229.

Kenmore checklist before a service call

  1. Read the model number on the door edge and note the prefix.
  2. Turn off the breaker.
  3. Pull the filter from the tub floor and wash it.
  4. Follow the drain hose for kinks; on a new install confirm the disposer knockout is out.
  5. Open the hot supply valve fully and make sure nothing pins the float.
  6. Use dishwasher detergent only, never hand soap.

Call a technician for your Kenmore when

  • Heater, motor, diverter or board codes return after the reset.
  • Water stays in the tub with a clean filter and clear hose.
  • i30, E15 or AE keeps coming back, or there is water on the floor.
  • Water flows in while the dishwasher is off, or you smell burning.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Kenmore dishwasher code FAQ

Who makes my Kenmore dishwasher?

Check the first three digits of the model number: 665 Whirlpool, 587 Frigidaire, 630 Bosch, 363 GE.

Why is the Clean light flashing?

On 665 models without a display, the blinks are a code. Count the two groups to get the F and E numbers.

How do I reset a Kenmore dishwasher?

Switch off its breaker for about five minutes, restore power and run one cycle.

What does i30 mean?

On a Frigidaire-built 587 Kenmore, water has reached the base pan. Turn off the water and look for the leak.

Sources: searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, producthelp.whirlpool.com, partstown.com, bosch-home.com, appliantology.org, ifixit.com, appliancepartspros.com. Codes and meanings can vary by model; check your owner’s manual.

720-230-1229
720-230-1229
Call Now Book Online