Miele Washer Fault Codes (F Codes)

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

The Miele washer codes owners see most are F10 or F15 (water inlet blocked), F11 (drain restricted), F16 or F56 (too much detergent or foam), F34 and F35 (door lock or release), and F138 or Waterproof system activated (a leak). Inlet and drain codes can usually be cleared by opening the faucet, cleaning the inlet filter and cleaning the drain filter. Electronic, drive, sensor and leak codes need a technician.

Miele washers show faults as an F followed by a number, or as a text message on newer displays. Some models flash the Drain or Check inlet light instead. The meanings below come from Miele's own help pages. Before any hands-on check, unplug the washer or switch off its breaker, and be careful: water in the drum and drain filter can be hot after a high-temperature wash.

Miele Washer Fault Codes (F Codes) error codes and what they mean

Code What it means What to try
F10 / Check inlet light flashing The water inlet is blocked or restricted. Open the faucet fully and restart. Turn off the faucet, unscrew the inlet hose, and clean the small filter. Straighten the hose. With the faucet open, at least 5 liters should flow in 15 seconds; if not, call a plumber.
F15 / Hot water inlet fault The hot water inlet is blocked or restricted. Open the hot water faucet and clean the filter in the hot inlet hose, then restart.
F11 / Drain light flashing The drain is restricted: a blocked drain filter or pump, or a drain hose problem. Keep the drain hose end no higher than 3 ft 3 in and remove kinks. Turn the washer off, open the drain pump panel, drain into a tray, clean the drain filter, and make sure the impeller turns freely.
F16 Too much detergent or detergent additives. Use less detergent and fewer additives, and pick a program that suits the load.
F56 The final spin ran below 400 rpm, usually because of foam from too much detergent. Reduce detergent to match your water hardness and soil level.
F20 / Heating fault Heating fault, or Thermostop paused the cycle because the set temperature was not reached in time. Unplug or switch off the breaker for at least 2 minutes, then restart. If it returns, call for service.
F34 / Door lock The washer could not lock the door (or the drum on top loaders), often because the drum is overloaded. Reduce the load. Switch off and on, then power down for 2 minutes if needed. If it persists, call for service.
F35 / Door release The washer could not unlock the door, usually a lock system fault.
Call a technician
Power down for at least 2 minutes and try again. If you must get the laundry out, unplug, drain the water through the drain filter first, then use the emergency release described in your manual.
F37 The washer is not level, or the drain hose is routed too high. Level the washer and keep the drain hose no higher than 3 ft 3 in.
F41 Electronics fault. Turn off for about 10 seconds and back on. If it returns, call for service.
F43 Electronics fault, or an option combination selected in the app that the machine does not support. Rerun with options that can be combined on your model. If it persists, call for service.
F62 The program selector is stuck between two settings. Turn the selector to a defined program position.
F92 Bacteria may be building up from long periods of low-temperature washing. Run Clean Machine or a Normal program at the maximum temperature before the next load.
F210 / Check filter + nozzle The suds circulation system is blocked, usually at the door-seal nozzle or the drain filter. Let the washer cool, switch it off, remove lint from the nozzle at the top of the door seal, then clean the drain filter.
F252 The door contacts near the hinge are dirty. Clean the door contacts. If it persists, call for service.
F373 Leak near the drain filter because it is not screwed in tightly. Screw the drain filters in tight by hand.
F138 / Waterproof system activated The Waterproof system detected a leak inside the washer; there is water in the base tray.
Call a technician
Unplug the washer, drain the water through the drain pump panel into a container, and call for service. Do not use the emergency door release before draining.
F220 Possible leak. It can appear without an actual leak.
Call a technician
Unplug and check for water. If there is none, run a program and connect the machine to Wi-Fi for the software update. If there is a leak, call for service.
F1 / F2 / F3 / F4 Temperature sensor faults: water sensor shorted (F1) or open (F2), heater bank sensor shorted (F3) or open (F4).
Call a technician
No owner fix. Call for service.
F19 Flow meter is stiff.
Call a technician
No owner fix. Call for service.
F29 / F81 / F83 / F105 / F106 Steam generator fault.
Call a technician
No owner fix. Call for service.
F50 / F53 / F104 Drum drive fault.
Call a technician
No owner fix. Call for service.
F51 / F63 / F64 Pressure sensor fault (F51), water flow control fault (F63), or magnetic field sensor fault (F64).
Call a technician
No owner fix. Call for service.
F39 / F44 / F45 / F47 / F49 / F130 Electronic faults that Miele says owners cannot fix.
Call a technician
Switch off and on once. If the code returns, call for service.
F65 Drum lighting fault.
Call a technician
No owner fix. Call for service.
F103 / F199 / F242 Communication faults: M-Bus module (F103), XCI box connection (F199), or touch display to electronics (F242).
Call a technician
No owner fix. Call for service.
F131 / F139 / F140 External dispenser unit faults: electronics (F131), water in the housing (F139), or mixing container water level too high (F140).
Call a technician
No owner fix. Call for service.
F211 / F212 / F213 / F214 TwinDos sensor fault on container 1 (F211 short, F212 open) or container 2 (F213 short, F214 open).
Call a technician
You can keep washing by adding detergent by hand. Book service for the TwinDos sensor.
noC / Ctr Not faults. noC means no Wi-Fi connection when MobileStart is selected; Ctr means SmartStart is active. For noC, check your Wi-Fi and reconnect the washer. For Ctr, turn off SmartStart in the programming menu if you do not use it.

What we find on Miele washers and similar washers in the Denver area

We see fewer Miele washers than the big-volume brands: 1 service call in our records since 2023. The parts that fail are much the same across brands, so here is what we found on all 1238 washer calls in our records since 2023.

The washer repairs we do most often (all brands)

  1. Control or display board: 108 calls
  2. Drain pump: 74 calls
  3. Shock absorbers or suspension: 57 calls
  4. Water inlet valve: 41 calls
  5. Door or lid lock: 28 calls
  6. Door boot seal: 27 calls
  7. Drive belt or coupler: 23 calls

Recent washer calls

  • Denver (80204), October 2026: GE washer not spinning. Diagnosis: drive belt or coupler.
  • Longmont (80503), October 2026: Maytag washer not draining. Repair: drain pump replaced.
  • Lakewood (80227), October 2026: Whirlpool washer door or lid problem. Repair: pressure or water-level sensor replaced.
  • Berthoud (80513), October 2026: Washer not starting. Diagnosis: drain pump.

Washer repairs from $240. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Miele washer error codes

Video by Miele Australia

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • Across all 1238 washer calls in our records (all brands), the repairs we do most often: control or display board (108 calls), drain pump (74) and shock absorbers or suspension (57).

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. Unplug the washer or switch off its breaker before any check.
  2. Make sure the faucets are fully open and clean the small filters in the inlet hoses.
  3. Straighten the drain hose and keep its end no higher than 3 ft 3 in.
  4. Drain and clean the drain filter behind the lower access panel; keep a shallow tray and towels ready.
  5. Use the right amount of detergent for your water hardness; too much causes F16 and F56.
  6. Do not overload the drum, and make sure the washer is level.
  7. After a reset, wait at least 2 minutes with power off before restarting.

When to call a technician

  • F138, F220 with visible water, or Waterproof system activated.
  • The door will not unlock after a 2-minute power reset.
  • Drive, sensor, steam generator or electronic codes appear.
  • F10 or F11 returns after cleaning the filters and checking the hoses.
  • The washer trips the breaker or smells hot.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

What does F11 mean on a Miele washer?

F11 means the drain is restricted. Check the drain hose for kinks and height, then drain and clean the drain filter behind the lower front panel.

What does F10 mean on a Miele washer?

F10 means not enough water is coming in. Make sure the faucet is fully open, clean the filter in the inlet hose, and straighten the hose.

How do I reset a Miele washer fault?

Unplug the washer or switch off its breaker for at least 2 minutes, restore power and restart the program. If the code returns, the fault still needs attention.

My Miele washer door is locked with F35. How do I get my clothes out?

Power down for 2 minutes first. If it stays locked, unplug the washer, drain the water through the drain filter, and then use the emergency release your manual describes.

Sources: mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com, mieleusa.com. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229

Photos from our job records

Real photos our technicians took on repair calls around Denver and the Front Range. Each caption says where the job was.

Washer repair in Parker, photo from our job records
Washer repair in Parker
Washer repair in Superior, photo from our job records
Washer repair in Superior
Washer repair in Niwot, photo from our job records
Washer repair in Niwot
Washer repair in Boulder, photo from our job records
Washer repair in Boulder
Call Now Book Online