Thermador Dishwasher Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

Thermador dishwasher codes fall into three common groups: drain faults (E22, E24, E25, also shown as E9240, E6103, E6102), no-fill faults (E16, E17, E18) and the leak alarm E15, also shown as E3100. A cleaned filter, a cleared pump cover, an open supply valve and a clear air gap solve many drain and fill codes. If a heater, relay, motor or sensor code returns after a 30-second breaker reset, it needs a repair visit.

Thermador belongs to BSH, the group that also makes Bosch, and the dishwashers share a control platform. Depending on model age the display shows either a short code (E24) or a four-digit code (E6103) for the same fault, so we list both side by side. Thermador’s own code page is our source; it also says which codes an owner can handle. A full reset is simply the breaker off for 30 seconds. For any hands-on check, cut power first, and close the water valve if you are looking for a leak.

Thermador dishwasher codes by category

Drain faults

Short / long code Thermador definition Owner action
E22 / E9240 The filter is clogged, or the pump, air gap or drain hose is restricted. Lift out and scrub the filter assembly, then work through the E24 checks.
E24 / E6103 (also written E-24, E61-03) Drain pump blocked, or the air gap or drain hose is clogged. Under the filter, pop off the pump cover and remove glass, seeds or labels. Snap the cover back until it clicks, straighten the hose, clear the air gap, run Rinse.
E25 / E6102 (also E-25, E61-02) Drain pump fault, or the same air gap or hose blockage. Same routine as E24.
E23 / E6101 Pump blocked, clogged or failed.
Technician
Clear the pump area once; a repeat means the pump.

Water supply and leak protection

Short / long code Thermador definition Owner action
E15 / E3100 Water in the base pan has triggered the leak protection.
Technician
Close the supply valve and book service. Hand dish soap can cause foam that sets this off.
E16, E17 / E3300, E3400 No water is coming in. Open the valve under the sink all the way; look for a crushed or kinked inlet hose.
E18 / E3200 Water level too low, or water is not being pumped correctly. Confirm strong flow at the supply, roughly 10 liters (2.6 gallons) per minute.
E14 / E3000 Flow meter failed, or a fill problem.
Technician
Check the valve is fully open, then book if it repeats.

Heating, scale and drying

Short / long code Thermador definition Owner action
E04 / E0105 Self-test found faulty heater electronics.
Technician
Book service.
E2030 / E6001 Heater inside the heat pump (circulation pump) has a fault.
Technician
Breaker off for 30 seconds. If it reappears, schedule a repair.
E12 / E2060 Lime scale has built up in the heat pump. Run a dishwasher descaler and keep the softener stocked with salt if you have one. Front Range hard water speeds up scaling.
E2120, E2130 CrystalDry zeolite drying system: chamber heater (E2120) or fan motor (E2130).
Technician
Breaker off for 30 seconds. If it reappears, schedule a repair.

Pump, wash arms, dispenser and door

Short / long code Thermador definition Owner action
E6002 The heat pump is blocked.
Technician
Breaker off for 30 seconds. If it reappears, schedule a repair.
E0100 Heat pump motor circuit fault on the main board.
Technician
Breaker off for 30 seconds. If it reappears, schedule a repair.
E0106 Wash arm diverter circuit fault on the main board.
Technician
Breaker off for 30 seconds. If it reappears, schedule a repair.
E6160 Zone Control lower spray arm could not find its home position.
Technician
Make sure a pan handle is not blocking the lower arm.
E6900 Detergent dispenser solenoid circuit.
Technician
Breaker off for 30 seconds. If it reappears, schedule a repair.
E8000 Door sensor circuit.
Technician
Breaker off for 30 seconds. If it reappears, schedule a repair.

Control board and house power

Short / long code Thermador definition Owner action
E0103, E0107 Relay fault on the main control board.
Technician
Breaker off for 30 seconds. If it reappears, schedule a repair.
E0110 The electronics are not communicating correctly.
Technician
Book service.
E27 / E9001 Incoming house voltage is too low. The dishwasher itself is fine. Reset the breaker; if it keeps happening, an electrician should measure the supply.
Salt or rinse aid symbol The reservoir shown needs a refill. Refill it.
UP Software was updated. Not a fault. Press any program button.

What we find on Thermador dishwashers and similar dishwashers in the Denver area

We see fewer Thermador dishwashers than the big-volume brands: 2 service calls in our records since 2023. The parts that fail are much the same across brands, so here is what we found on all 702 dishwasher calls in our records since 2023.

The dishwasher repairs we do most often (all brands)

  1. Circulation pump or wash motor: 51 calls
  2. Control board: 35 calls
  3. Drain pump: 34 calls
  4. Water inlet valve: 13 calls
  5. Clogged filter or drain: 13 calls
  6. Door latch or seal: 12 calls
  7. Heating element: 11 calls

Recent dishwasher calls

  • Erie (80516), October 2026: GE dishwasher not heating. Repair: heating element replaced (WD21X22830).
  • Longmont (80504), October 2026: Dishwasher stopping mid-cycle. Repair: drain pump replaced (WD19X25461).
  • Arvada (80002), October 2026: Dishwasher leaking. Repair: water inlet valve replaced (DD82-01383A).
  • Boulder (80304), September 2026: Dishwasher leaking. Repair: circulation pump or wash motor replaced (W10155344).

Dishwasher repairs from $220. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Thermador dishwasher error codes

Video by Matthew Brenengen

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • Across all 702 dishwasher calls in our records (all brands), the repairs we do most often: circulation pump or wash motor (51 calls), control board (35) and drain pump (34).

Don’t want to do it yourself? Call 720-230-1229.

Owner checks, in order

  1. Switch off the dishwasher breaker.
  2. Twist out the filter in the tub floor and wash it.
  3. Remove the pump cover beneath it, clear debris, click it back in place.
  4. Follow the drain hose for kinks and clean the air gap on the sink deck.
  5. Confirm the supply valve is fully open, then restore power after 30 seconds.
  6. Use automatic dishwasher detergent only.

Book a Thermador repair if

  • E15 / E3100 shows, or you find water under the unit.
  • It still holds water after the filter and pump area are clean.
  • A heater, relay, motor, diverter or sensor code comes back.
  • It will not fill with the valve fully open, or low-voltage codes keep recurring.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Thermador dishwasher code FAQ

How do I reset a Thermador dishwasher?

Turn its breaker off for 30 seconds and back on. That clears a one-time fault; a repeat code points to a real problem.

What does E24 mean?

Water is not draining: the pump is blocked or the hose or air gap is clogged. Clean the pump area and clear the drain line.

What does E15 mean?

Water has reached the base and leak protection has activated. Turn off the water and arrange service.

Why does my Thermador show E6103 instead of E24?

Newer controls use four-digit codes. E6103 and E24 describe the same drain fault.

Sources: thermador.com, thermador.com. Codes and meanings can vary by model; check your owner’s manual.

720-230-1229
720-230-1229
Call Now Book Online