Bosch Oven Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

On Bosch ovens, E011 (E11) means a touch key is stuck or was held too long, often from moisture, and E115 means the oven cavity got too hot, so the door may stay locked until it cools. E3xx codes such as E302, E303 and E305 point to an overheating or communicating control module. Older Bosch wall ovens use F codes: F31 and F32 are oven sensor faults and F41 to F45 are door latch faults. If a code returns after the oven cools and power is reset, call a technician.

Bosch has used several code systems: current ovens and ranges show E codes (E011, E115, E302), older 500 and 800 series wall ovens and ranges show F codes (F31, F41, F121), and induction ranges add cooktop codes. Bosch's US support pages list many codes without meanings and refer owners to support, so this list also uses Bosch manuals and parts references; those meanings are marked as commonly reported. Codes vary by model, so check your manual.

Bosch Oven error codes and what they mean

Code What it means What to try
E011 / E11 A button was pressed too long or is stuck, or the touch keys are not working normally. Condensation on the panel is a common cause. Turn the oven off, dry the control panel and press the buttons one at a time. Reset the breaker for a minute. If it returns, the touch control or control board needs service.
E115 The cooking compartment is too hot. The door may stay locked as a safety measure.
Call a technician
Turn the oven off and let it cool for at least 30 minutes with the door closed. If E115 returns during normal cooking, have the sensor and control checked.
E118 Commonly reported as the oven being unable to read its temperature sensor correctly (sensor, wiring or communication fault).
Call a technician
Reset power once. If it returns, a technician should test the sensor and wiring.
E005 User interface and power board are not communicating correctly, or a power supply or wiring problem.
Call a technician
Turn the power off at the breaker for 30 seconds to a minute, then back on. If the code returns, request service.
E100 / E900 Electronics or main control board communication fault.
Call a technician
Turn the power off at the breaker for 30 seconds to a minute, then back on. If the code returns, request service.
E101 Temperature-sensing system fault (oven sensor or its circuit).
Call a technician
Reset power once. If it returns, a technician should test the sensor and wiring.
E126 Oven door lock fault, often around self-clean.
Call a technician
Let the oven cool fully and reset power. Do not force the door. If it stays locked, request service.
E301 Commonly reported as a control board or touch panel communication fault.
Call a technician
Turn the power off at the breaker for 30 seconds to a minute, then back on. If the code returns, request service.
E302 / E303 The control module got too hot (around 212°F). The oven shuts off the heating elements and runs the cooling fan. A failed cooling fan or blocked vents are the most common causes.
Call a technician
Turn the oven off and let it cool. Make sure nothing blocks the vents. If it returns, a technician should check the cooling fan and control.
E305 Depending on model: communication loss between the touch control module and the main control (for example on 800 series slide-in gas ranges), or a door lock that will not engage or release.
Call a technician
Turn the power off at the breaker for 30 seconds to a minute, then back on. If the code returns, request service.
E310 Electrical supply failure.
Call a technician
Check that the breaker is fully on. If it returns, have the power supply checked, then request service.
ERR / toP A cooktop zone was turned on while Self Clean is running. Turn off the cooktop zone and let the self-clean finish.
E0532 / E05-32 European-style code: stuck button. Press the buttons one at a time and dry the panel. If it persists, request service.
E0511 / E8401 European-style code: temperature sensor problem.
Call a technician
Turn the oven off for about 20 minutes. If it returns, request service.
E6200 European-style code: oven fan problem.
Call a technician
Turn the oven off. A technician should check the fan for blockage, mounting and wiring.
E5116 Steam ovens (European models): air in the steam system, often on first use. Run a steam or regeneration program for about 5 minutes and repeat if needed. If it persists, request service.
F1 (older models) Commonly reported as a meat probe fault found during a test or service mode cycle.
Call a technician
Check that the probe plug is fully seated and undamaged. If it returns, request service.
F2 / F3 (older models) Commonly reported as an oven temperature sensor fault (F2) or a warming drawer sensor fault (F3).
Call a technician
Reset power once. If it returns, a technician should test the sensor and wiring.
F31 / F32 Oven temperature sensor failure: shorted (F31) or open circuit (F32). On double ovens, F32 can mean the lower oven sensor.
Call a technician
Reset power once. If it returns, a technician should test the sensor and wiring.
F33 / F34 Warming drawer temperature sensor shorted (F33) or open (F34).
Call a technician
Reset power once. If it returns, request service.
F41 / F42 Motorized door latch will not lock: upper or single oven (F41) or lower oven (F42).
Call a technician
Let the oven cool and reset power. Do not force the door. If it returns, request service.
F43 / F44 Door latch will not unlock: upper or single oven (F43) or lower oven (F44).
Call a technician
Let the oven cool fully and reset power. Do not force the door. If it stays locked, request service.
F45 A door latch switch is stuck or faulty (latch reads both locked and unlocked).
Call a technician
Let the oven cool and reset power. If it returns, request service.
F111 Oven overheated in Bake or Broil (above about 585°F).
Call a technician
Turn the oven off at the breaker and let it cool. Do not use it until it is checked.
F113 Oven overheated in self-clean (above about 950°F).
Call a technician
Turn the oven off at the breaker and let it cool. Do not use it until it is checked.
F112 / F114 Listed by parts references without a public meaning; the neighboring codes F111 and F113 are overheating faults.
Call a technician
Control-detected fault. Reset power at the breaker for a minute (or unplug for 5 minutes); if it returns, call a technician.
F121 A key on the control panel is stuck (continuously closed).
Call a technician
Clean and dry the panel and reset power. If it returns, the keypad needs replacing.
F125 The Cancel key is stuck.
Call a technician
Clean and dry the panel and reset power. If it returns, request service.
F151 Electronic control board failure or communication error.
Call a technician
Turn the power off at the breaker for 30 seconds to a minute, then back on. If the code returns, request service.
F154 Electronic control board is overheating.
Call a technician
Turn the oven off and let it cool. If it returns, a technician should check the cooling fan and control.
F170 A power failure occurred. Reset the clock. If it returns without outages, request service.
E9000 / E9010 / U400 Induction range: supply voltage outside the permitted range.
Call a technician
Have an electrician check the supply voltage, then request service if it returns.
E9011 Induction range: the appliance is not connected properly.
Call a technician
Turn off the breaker and have the installer or an electrician check the connection.
E7015 / F2 / F4 (induction) Induction cooktop: electronics overheated and the cooking zone shut off. Let the cooktop cool. Keep vents clear. If it keeps happening, request service.
F1 / F6 (induction) Induction cooktop: the cooking zone overheated and shut off to protect the surface. Let the cooktop cool, and do not heat empty pans. If it keeps happening, request service.
F5 (induction) Hot cookware is sitting near the control panel; electronics may overheat. Move hot pans away from the controls.
F8 + H/h (induction) Automatic operating-time limit turned the cooking zone off. Turn the zone back on if you are still cooking.
dE / Demo Demo mode is on; the oven does not heat but the buttons work. Turn demo mode off in the settings menu (see your manual). Unplugging or resetting power for about 20 seconds first can help.
Key or lock symbol Child lock is on. Not a fault. Press and hold the key-symbol button until the symbol goes away.

What we actually find on Bosch ovens in the Denver area

The codes above come from Bosch’s own documentation. This section shows what our technicians found once they opened the machine. Since 2024 we have handled 12 Bosch oven service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The oven repairs we do most often (all brands)

Our notes on Bosch ovens are too thin to rank by brand alone, so here is what we found across all 645 oven calls in our records:

  1. Control board: 54 calls
  2. Igniter: 45 calls
  3. Bake or broil element: 26 calls
  4. Surface element or burner switch: 20 calls
  5. Wiring: 16 calls
  6. Convection fan: 15 calls
  7. Temperature sensor: 13 calls

Bosch oven repairs from $200. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2024–2026. Customer details removed.

What you can safely check yourself

  1. Turn the oven off and let it cool fully, at least 30 minutes after an overheating code such as E115.
  2. Dry the control panel and press buttons one at a time if you see E011 or a stuck-key code.
  3. Turn the breaker off for about a minute, then back on, to see if the code clears.
  4. Make sure vents around the oven and cooktop are not blocked.
  5. Check that the child lock and demo mode are off.
  6. For gas ranges, never adjust gas connections yourself.

When to call a technician

  • Any E or F code returns after the oven cools and power is reset.
  • The oven overheats (E115, F111, F113) during normal cooking.
  • The door stays locked after the oven has cooled (F43, F44, E126).
  • A control overheating code (E302, E303, F154) keeps returning, or you smell burning or gas.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

What does E011 mean on a Bosch oven?

E011 (E11) means a button was pressed too long or is stuck, often because of moisture on the touch panel. Dry the panel and reset power. If it keeps returning, the touch control or control board needs service.

What does E115 mean on a Bosch oven?

E115 means the oven cavity is too hot, and the door may stay locked until it cools. Turn the oven off and let it cool for at least 30 minutes. If it happens again in normal cooking, have the sensor and control checked.

What does F41 mean on a Bosch oven?

F41 means the motorized door latch on the upper or single oven will not lock. The latch, its switches, the latch motor or the wiring are the usual causes.

How do I reset my Bosch oven?

Turn the oven off, let it cool, then switch off its circuit breaker for about a minute and turn it back on. If the code returns, a technician needs to diagnose it.

Sources: bosch-home.com, bosch-home.com, coolblue.nl, searspartsdirect.com, appliancepartspros.com, appliancepartspros.com, appliancepartspros.com, appliancepartspros.com, appliancepartspros.com, appliancepartspros.com, appliancepartspros.com, genuinereplacementparts.com. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229
Call Now Book Online