The Maytag dishwasher codes owners run into most are F9E1 (the tub is draining too slowly), F8E4 (water has reached the drip tray), H20 (no water came in), F6E1 (fill fault on older units, control fault on newer ones) and F7E2 (wash motor on newer units, heater on older ones). A clean filter, a clear drain hose, an open supply valve and an emptied drip tray resolve a good share of them. Motor, heater, sensor and board codes that return after a 30-second power cut need a technician.
Maytag dishwashers run Whirlpool’s F#E# system. Units with a screen print the code. Units without one use the Clean light: rapid blinks give the F number, a 1 to 2 second gap, then blinks for the E number, repeating about every 5 seconds. Watch it twice. Because some numbers were reassigned between control generations, rows below show both meanings where sources disagree. We used Maytag and Whirlpool help pages plus Sears parts documentation. Switch the breaker off before working inside the tub.
Maytag dishwasher codes grouped by job
Getting water out
| Code | Maytag diagnosis | Worth trying |
|---|---|---|
F9E1 (9, 1) |
Newer: drain takes too long. Some older: diverter disc position not detected. | Rinse the filter, check the hose for kinks, run the disposer, confirm its knockout plug is gone, and clean the air gap cap. |
F9E2, F9E3, F9E4 |
Newer: drain motor error (E2). Older: diverter motor stuck on (E2), disc missing (E3), lower arm blocked (E4). Technician |
Spin the lower arm by hand. 30 seconds without power; if it returns, book a repair. |
F8E1, F8E2 |
Older: slow drain (E1) or pump electrical fault (E2). | Filter and hose first, then the pump. |
F3E3 |
Optical sensor calibration failed, or dirty water is siphoning back through a failed check valve. Technician |
Add a high loop under the counter or an air gap. |
Getting water in, and keeping it in
| Code | Maytag diagnosis | Worth trying |
|---|---|---|
H20 / H2O |
No incoming water sensed. | Open the valve under the sink and straighten the supply line. |
F6E1 (6, 1) |
Newer: control or interface error. Older: no fill. Technician |
Check water is on and the float is free. 30 seconds without power; if it returns, book a repair. |
F6E2, F6E6, F6E7, F6E8 |
Older: inlet valve (E2), water too cold (E6), flow meter (E7), softener valve (E8). Technician |
For E6, run the tap hot before starting. Others: 30 seconds without power; if it returns, book a repair. |
F6E3 |
Suds overload, or air in the pump and low water on older units. | Dishwasher detergent only, then an empty rinse. |
F6E4 |
Overfill float switch reads open. | Free the float. If water enters with the machine off, close the valve and call. |
F8E5 |
Fill valve stuck open; water keeps coming. Technician |
Shut the supply valve immediately. |
F8E4 (8, 4) |
Newer: water in the drip tray. Some older: drain pump motor failed. | Cut power and water, empty the tray, check that the float switch is connected and the fittings are dry. |
Heating, washing and drying
| Code | Maytag diagnosis | Worth trying |
|---|---|---|
F7E2 |
Newer: wash motor fault. Older: heating element stuck on. Technician |
30 seconds without power; if it returns, book a repair. |
F7E1, F4E2, F4E3 |
Element not working (F7E1, older) or heating system error (F4E2, F4E3, newer). On some older units F4E2 is a pump communication fault. Technician |
Cold, wet dishes plus a repeat code confirm it. |
F4E1, F4E4 |
Board cannot talk to the circulation pump motor. Technician |
30 seconds without power; if it returns, book a repair. |
F3E1, F3E2 |
Thermistor or OWI sensor open or shorted. Technician |
30 seconds without power; if it returns, book a repair. |
FAE1, FAE3, FAE4 (10, x) |
Dispenser (E1), drying fan (E3), diverter valve (E4, also F10E4). Technician |
Move tall items that block the dispenser lid or spray arms. |
Door, panel, board and Wi-Fi
| Code | Maytag diagnosis | Worth trying |
|---|---|---|
F5E1, F5E2 |
Door switch (E1), or no door opening seen between cycles (E2). | Open, close, restart, and shut the door within seconds of pressing Start. |
F2E1, F2E2 |
Stuck key (E1) or panel not reaching the board (E2). Technician |
Press each key firmly, then one reset. |
F1E1, F1E2 |
Board relay stuck (E1) or board fault (E2). Technician |
Five minutes without power; a repeat means the board. |
FCE1, FCE2, FCE3, FCE5 (12, x) |
Wi-Fi module, router, internet or antenna. Washing still works. | Re-pair the dishwasher with your router. |
What we actually find on Maytag dishwashers in the Denver area
The codes above come from Maytag’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 14 Maytag dishwasher service calls across the Denver metro and Boulder County. Every number here comes from our own job records.
The dishwasher repairs we do most often (all brands)
Our notes on Maytag dishwashers are too thin to rank by brand alone, so here is what we found across all 702 dishwasher calls in our records:
- Circulation pump or wash motor: 51 calls
- Control board: 35 calls
- Drain pump: 34 calls
- Water inlet valve: 13 calls
- Clogged filter or drain: 13 calls
- Door latch or seal: 12 calls
- Heating element: 11 calls
Recent Maytag dishwasher calls
- Lafayette (80026), October 2026: Maytag dishwasher not draining. Repair: drain pump replaced.
- Denver (80246), June 2026: Maytag dishwasher not starting. Repair: control board replaced.
Dishwasher repairs from $220. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.
Source: The Appliance Team service records, 2023–2026. Customer details removed.
Video: Maytag dishwasher error codes
Video by Parts Dr
What we see on Denver calls
- An error code points to the system that reported the fault, not always to the part that failed.
- Across all 702 dishwasher calls in our records (all brands), the repairs we do most often: circulation pump or wash motor (51 calls), control board (35) and drain pump (34).
- Recent call: Lafayette (80026), October 2026: Maytag dishwasher not draining. Repair: drain pump replaced.
Don’t want to do it yourself? Call 720-230-1229.
Quick fixes to try first
- Breaker off (or unplug).
- Twist out the filter and rinse it under the tap.
- Check the drain hose and, on a new install, the disposer knockout.
- Make sure the supply valve under the sink is all the way open.
- Power back on after 30 seconds and run one cycle with dishwasher detergent only.
Book a Maytag dishwasher repair if
- A motor, heater, sensor or board code returns.
- It holds water even with a clean filter and clear hose.
- F8E4 keeps coming back or water reaches the floor.
- F8E5 shows, or you smell burning near the door or panel.
How to prevent this
Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:
Maytag dishwasher code FAQ
How do I reset a Maytag dishwasher?
Switch off its breaker or unplug it for 30 seconds, then restart a cycle.
What does F9E1 mean?
On current models the dishwasher is draining too slowly. Clean the filter and check the hose, disposer and air gap.
Why is the Clean light blinking?
On models without a display the blinks are a code: count the first group for F and the second for E.
What does F8E4 mean?
On current models water has reached the drip tray under the tub. Turn off the water, empty the tray and look for the leak.
Sources: producthelp.maytag.com, producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, searspartsdirect.com, searspartsdirect.com. Codes and meanings can vary by model; check your owner’s manual.



