Samsung Dishwasher Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

The most common Samsung dishwasher codes are 4C/4E (not enough water coming in), 5C/5E (not draining), LC/LE (leak detected) and OC/OE (too much water). Many of these clear after you open the water valve, clean the filter and drain hose, or dry out a leak. Heater, pump, sensor and communication codes (HE, HC, 3C, tE, CE) that come back after a restart need a technician.

Samsung dishwashers with a digital display show a two-character code when a cycle stops. Models without a display flash lights instead. Samsung recommends troubleshooting before you reset or clear a code, because a reset alone does not fix the cause. Turn off power at the breaker and shut off the water supply before any hands-on check. The list combines the manufacturer's own code lists with service manuals and repair-parts references. Rows marked "on some models" or "service references" come from those repair sources, so the meaning can vary by model; check your owner's manual when in doubt.

Samsung Dishwasher error codes and what they mean

Code What it means What to try
4C / 4E Water supply error: water pressure or temperature is too low. Make sure the shutoff valve under the sink is fully open and the inlet hose is not kinked. If other faucets have low pressure, the issue is the home supply.
4C5 / 4E5 Fill error: the dishwasher starts to fill, then stops early with little or no water in the tub. Service references also link 4E5 to a leaking water valve that lets water in when it should be closed. Make sure the shutoff valve is fully open and the inlet hose is not kinked or crushed. If household water pressure is normal and the code returns, request service.
4E1 On some models: water entering the dishwasher is hotter than 176 F. Check that the water heater is not set too high. If it is set normally and the code continues, request service.
5C / 5E / SC / SE / SR / nE / 5C1 Drain error: the dishwasher cannot drain. On DMT300-series models the drain error shows as nE. With power off, clean the filters at the bottom of the tub. Check the drain hose for kinks. If you have a garbage disposal, run it, and make sure the knockout plug was removed when the dishwasher was installed.
5C2 Drain pump fails to start, runs briefly, or stalls, often because debris is jamming the pump. Turn off power at the breaker. Remove the lower rack and filters and check the sump for glass, seeds or other debris. Reinstall and retry. If it still will not drain, request service.
LC / LE Leak detected. The dishwasher may turn on by itself and try to drain.
Call a technician
Turn off power and water. Look for leaks at the door, hoses and under the unit. Too much detergent or regular dish soap can cause suds that overflow. On Waterwall models, check that the reflector is not blocked. If you cannot find the leak, request service.
OC / 0C / OE Over-level water error: too much water in the tub.
Call a technician
Clean the filters and check the drain hose, since poor draining can trigger this. If the dishwasher keeps filling with power off, the inlet valve may be stuck open.
1E / IE (Waterwall models) Clogged filter. Remove and clean the fine filter at the bottom of the dishwasher. If the code returns, request service.
1E / IE (Rotary models) High temperature heater error.
Call a technician
Turn off the breaker for 30 seconds, empty the dishwasher, add detergent and run a Normal cycle. If it returns, request service.
1C Low water level: the dishwasher fills briefly, then drains with little water. Clean the filters, use dishwasher detergent only, load evenly, and turn the dishwasher off for 5 minutes. If it continues, request service.
3C Pump operation error: the pump failed to run.
Call a technician
Turn the dishwasher off and restart the cycle. If the code persists, request service.
3E Incoming water is too hot. Make sure the water heater is not set above 176 F. If it is set correctly and the code continues, request service.
3E (other models) On some models 3C/3E is a pump operation error, and on some Waterwall models 3E is a communication failure. Check your manual.
Call a technician
Turn the dishwasher off for one minute and restart. If the code returns, request service.
7E Waterwall reflector error: the reflector cannot move correctly. Check that no dishes or utensils block the reflector track at the back of the lower rack. If it is clear and the code returns, request service.
7C On some models: the spray bar moves briefly, then stops, so cleaning is poor.
Call a technician
Check that nothing blocks the spray arms or bar, then restart. If it returns, request service.
9E Low water level error.
Call a technician
Empty the dishwasher, add detergent and run a Normal cycle. If it continues, turn off power at the breaker and request service.
9C1 / 9E1 / UC Abnormal supply voltage. The dishwasher powers on but goes into protection mode and will not wash. Turn off the breaker for at least one minute, then restore power. Do not use an extension cord. If it keeps happening, have the circuit checked.
9C2 Low or unstable voltage, often after brownouts or breaker trips. Turn off power for 5 minutes and restart. If it keeps happening, have the circuit checked.
HC High temperature heater error: the interior is too hot.
Call a technician
Turn off the breaker for 30 seconds, empty the dishwasher, add detergent and run a Normal cycle. If it recurs, request service.
HE Heater error: interior temperature reads incorrectly.
Call a technician
Empty the dishwasher, add detergent and run a Normal cycle. If it continues, turn off the breaker and request service.
HE1 On some models: heater failure. On others: the tub water is 176 F or hotter.
Call a technician
Turn off the breaker for 30 seconds, then run a Normal cycle with detergent. Check that the water heater is not set too high. If it returns, request service.
HC1 Water got too hot during washing, often from very hot inlet water or clogged filters. Make sure the inlet water is not excessively hot and clean the filters. If it continues, request service.
HC2 / HC4 On some models: heat or vent error during the drying phase. Keep the door vent uncovered and do not load tall plastics against the inner vent. If it continues, request service.
tE Temperature sensor error.
Call a technician
Empty the dishwasher, add detergent and run a Normal cycle. If it continues, turn off the breaker and request service.
tE1 / tE2 / tC Temperature sensor (thermistor) error.
Call a technician
Turn off power at the breaker for 5 minutes, then try a Normal cycle. If it continues, request service.
tC1 / tC2 On some models: drying temperature sensor error. Washing completes but drying ends early.
Call a technician
Keep the door vent uncovered and let air circulate. Power off for 5 minutes and retry. If it continues, request service.
bE / 6E / 6C / 6E2 A control panel button is stuck. Turn the dishwasher off and press every button. If a button sticks or the code returns, request service.
bE2 / bC2 A button has been pressed or held for more than 30 seconds. Tap buttons briefly instead of holding them. Wipe the control panel dry. Turn off power for 10 minutes and restart. If it continues, request service.
bE3 / bC3 Erratic touch panel, often after spills, steam or wiping. On some Waterwall models it is a communication error. Dry the panel with a lint-free cloth, turn off power for at least 30 seconds, and restart. If it continues, request service.
6C1 On some models: detergent dispenser motor error. Unplug or turn off the breaker for 5 minutes. Make sure a tablet is not stuck in the dispenser. If it returns, request service.
dE / DC Door latch error: the door is not detected as closed, or the latch is defective. Close the door firmly and make sure no utensils or racks stick out. Clean the latch area and power off for 30 seconds. If it continues, the latch needs service.
CE Communication error: the control panel cannot communicate with the main board.
Call a technician
Turn the dishwasher off and back on. If it continues, request service.
AC / CA / AE Communication error between the main and sub control boards.
Call a technician
Turn off the breaker for one minute, then restore power and try again. If it continues, request service.
AC6 / AE6 Communication error; the panel lights but Start does nothing.
Call a technician
Turn off the breaker or unplug for 10 minutes, then try a cycle. If it continues, request service.
FC / FC2 / FC3 / FC4 On models with fan-assisted drying: drying fan error. Dishes stay wet and the cycle may end early.
Call a technician
Make sure the door vent is not blocked, power off for 5 minutes and retry. If it continues, the fan needs service.
PC Zone Wash error.
Call a technician
Turn the dishwasher off and restart the cycle. If it persists, request service.
PE Half load function error.
Call a technician
Empty the dishwasher, add detergent and run a half load cycle. If it continues, turn off the breaker and request service.
AP Access Point mode for connecting to a phone. Not a fault. If you are not connecting a device, turn the dishwasher off and back on.
Circulation (wash) pump error variants, same family as 3C.
Call a technician
Turn off power at the breaker for 5 minutes, clean the filter and restart. If it returns, call a technician.
Drain pump error variants (service references): the drain pump faulted repeatedly and the dishwasher stopped.
Call a technician
Clean the filter and check the drain hose for kinks. If it returns, the drain pump needs service.
4E2 (some models) On some models (service references): incoming water is too hot (about 176 F / 80 C or higher).
Call a technician
Lower the water heater setting if it is very high, or connect to a cooler supply. If it returns, call a technician.
dC1 / dC3 On models with Auto Door Open (service references): door signal error (dC1) or the auto door actuator failed (dC3).
Call a technician
Open and close the door firmly. If it returns, call a technician.
dO / dW Door open warning on some models. Not a fault. Close the door fully until it latches.
C3 On some models (service references): turbidity (soil) sensor error.
Call a technician
Unplug the appliance for 5 minutes, then restart. If the code returns, write it down and call a technician.
WE On some models (service references): water supply error, same as 4E. Check that the water valve under the sink is fully open and the hose is not kinked.
E1 / E3 / E4 (older models) Older Samsung codes (service references): E1 fill error (not enough water), E3 water entering when it should not, E4 overflow switch stuck on.
Call a technician
For E1, open the water valve fully. For E3 or E4, turn off the water and call a technician.
E6 / E7 (older models) Older Samsung codes (service references): temperature sensor (thermistor) short (E6) or open (E7).
Call a technician
Unplug the appliance for 5 minutes, then restart. If the code returns, write it down and call a technician.
IE (some models) Depending on model: clogged filter (Waterwall), heater error (rotary), or, per service references, an inverter communication error.
Call a technician
Clean the filter first. If IE returns, call a technician.
LE (some models) On some models service references describe LE as a low water level error rather than a leak.
Call a technician
Check that the water valve is fully open, then look under the unit for water. If it returns, call a technician.

What we actually find on Samsung dishwashers in the Denver area

The codes above come from Samsung’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 33 Samsung dishwasher service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The Samsung dishwasher repairs we do most often

Across all 33 Samsung dishwasher calls, with or without a code on the display:

  1. Drain pump: 6 calls
  2. Circulation pump or wash motor: 5 calls

Recent Samsung dishwasher calls

  • Superior (80027), May 2026: Samsung dishwasher not draining. Diagnosis: drain pump.
  • Denver metro, April 2026: Samsung dishwasher not starting. Repair: circulation pump or wash motor replaced.
  • Broomfield (80020), November 2024: Samsung dishwasher not cleaning. Repair: pressure or turbidity sensor replaced.
  • Erie (80516), November 2024: Samsung dishwasher leaking. Repair: circulation pump or wash motor replaced.

Samsung dishwasher repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Samsung dishwasher drain pump repair

Video by Parts Dr

What we see on Denver calls

  • The video shows a drain pump repair. It is the most common dishwasher repair on our calls.
  • The Samsung dishwasher repairs we do most often across the Denver metro and Boulder County: drain pump (6 calls) and circulation pump or wash motor (5).
  • Recent call: Broomfield (80020), November 2024: Samsung dishwasher not cleaning. Repair: pressure or turbidity sensor replaced.

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. Turn off power at the breaker and close the water valve before any hands-on check.
  2. Remove and rinse the filters at the bottom of the tub. Denver's hard water and food debris clog them over time.
  3. Check the drain hose under the sink for kinks, and run the garbage disposal if one is connected.
  4. Make sure the water valve under the sink is fully open.
  5. Use only dishwasher detergent, never dish soap, to avoid suds and leak codes.
  6. Check that nothing blocks the spray arms or the Waterwall reflector.

When to call a technician

  • Heater, pump, sensor or communication codes (HE, HC, 3C, tE, CE) return after a restart.
  • Water stays in the tub after the filters and drain hose are clear.
  • You see water on the floor or the LC/LE code keeps coming back.
  • The dishwasher keeps filling or runs on its own with the door closed.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

How do I reset a Samsung dishwasher error code?

Turn off the breaker for about 30 seconds, then turn it back on and run a cycle. Fix the cause first, or the code will come back.

What does LC mean on a Samsung dishwasher?

LC or LE means the leak sensor detected moisture. The dishwasher may try to drain and will not run until the sensor dries. Find and fix the leak, and avoid using dish soap or too much detergent.

Why does my Samsung dishwasher show 5C?

5C or 5E means the dishwasher cannot drain. Clean the filters, check the drain hose for kinks, and run the garbage disposal. If water still stays in the tub, the drain pump may need service.

Does 1E mean the same thing on every Samsung dishwasher?

No. On Waterwall models 1E means a clogged filter, while on Rotary models it means a high temperature heater error. Check your manual or model label to see which type you have.

Sources: samsung.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, samsung.com, samsung.com, samsung.com, samsung.com, mypros.plus, mypros.plus. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229

Photos from our job records

Real photos our technicians took on repair calls around Denver and the Front Range. Each caption says where the job was.

Dishwasher repair in Centennial, photo from our job records
Dishwasher repair in Centennial
Dishwasher repair in Centennial, photo from our job records
Dishwasher repair in Centennial
Dishwasher repair in Cherry Creek, photo from our job records
Dishwasher repair in Cherry Creek
Dishwasher repair in Longmont, photo from our job records
Dishwasher repair in Longmont
Call Now Book Online