Bosch Washer Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

On most Bosch washers, E16/F16 means the door is open, E17/F17 means the washer took too long to fill, and E18/F18 means it is not draining because the pump or hose is blocked. E23/F23 means the AquaStop leak protection triggered, so shut off the water and call for service. Heating, pressure sensor, flow sensor and communication codes also need a technician.

Bosch front-load washers show codes as E or F followed by a number, and the two letters usually mean the same fault (E18 and F18, for example). Older Nexxt models use Er codes instead. Some codes differ by model, so check your use and care manual. Before any hands-on check, unplug the washer and turn off the water taps; drained water may be very hot. This list combines the manufacturer's own documentation with codes reported by established repair-parts references (such as Sears PartsDirect, PartSelect and repair technicians' guides); those are marked "commonly reported" or "on some models".

Bosch Washer error codes and what they mean

Code What it means What to try
E16 / F16 Door is open or not fully closed. Close the door firmly and check that no clothing is caught in the seal. If the code returns, the door lock needs service.
E17 / F17 Water supply time exceeded: the washer is not filling fast enough. Turn the water taps fully on and check the inlet hoses for kinks. Unplugged and with taps off, clean the filter screens in the hose connections.
E18 / F18 Not draining: the drain pump is blocked or the drain hose is kinked or clogged. Unplug the washer. Check the drain hose for kinks. Open the service flap, drain the remaining water into a shallow pan, and clean the pump filter. Make sure the impeller turns freely, then refit the cover firmly.
E19 / F19 Heating time exceeded: the water did not heat up in time.
Call a technician
Power off for a few minutes and restart. If it returns, the heater or sensor needs service.
E20 / F20 Unexpected heating: the water heated when it should not have.
Call a technician
Unplug the washer and request service.
E23 / F23 AquaStop hose leak protection was activated, which usually means a leak.
Call a technician
Turn off the water tap right away and do not use the washer until it is repaired.
E25 / F25 Turbidity (water cloudiness) sensor problem.
Call a technician
Power off and restart. If it returns, request service.
E26 / F26 / F27 Pressure sensor problem (water level sensing).
Call a technician
Power off and restart. If it returns, request service.
E28 / F28 Flow sensor problem.
Call a technician
Make sure the water taps are fully open, then restart. If it returns, request service.
E56 Internal communication error between control parts.
Call a technician
Unplug for a few minutes and restart. If it repeats, request service.
E:18 (some models, e.g. WAT28400UC) Too much detergent, non-HE detergent, or a blocked drain pump. Use less HE detergent and clean the drain pump filter.
E:32 (some models) Unbalanced load stopped the spin. Not a fault; it may alternate with END. Spread out the laundry, add or remove items so the load balances, and run an extra spin.
E:93 (some models) No hot water reached the washer: tap off, hose kinked, low hot water pressure or a clogged hot inlet screen. Open the hot water tap, check the hot hose and clean its inlet screen. The code clears after a cycle with hot water.
Er:01 (Nexxt) Door is open or the door lock is not detected. Close the door firmly. If it returns, the door lock or its wiring needs service.
Er:11 / Er:12 (Nexxt) Fill time exceeded. Open both supply valves fully, check hoses for kinks or freezing, and make sure the drain hose is not siphoning.
Er:13 (Nexxt) Drain time exceeded. Clear the drain hose and house drain, and clean the large-item filter at the drain pump.
Er:14 (Nexxt) Overfill level reached.
Call a technician
Turn off the water taps. If the washer fills while unplugged, the inlet valve is stuck open. Request service.
Er:17 (Nexxt) AquaStop: water detected in the base of the cabinet.
Call a technician
Turn off the water and unplug the washer. Request service to find and fix the leak.
Er:20 (Nexxt) Spin stopped: badly unbalanced load or lost communication between control modules. Rebalance the load and remove some items. If it still will not spin, request service.
Er:21 (Nexxt) Too much foam. Use the right amount of HE detergent; most loads need very little.
Er:05 / Er:06 / Er:07 / Er:08 / Er:09 (Nexxt) Water temperature sensor (05, 06), heater control (07, 08) or motor control communication (09) problem.
Call a technician
Unplug for 3 minutes and restart. If it returns, request service.
E21 / F21 Commonly reported as a motor fault: the drum is blocked, the motor brushes are worn, or the motor has failed.
Call a technician
Unplug the washer and check that the drum turns by hand and nothing is caught between drum and tub. If it does, call a technician.
E:30 / -80 Drain problem: the drain pipe or hose is blocked, kinked or installed too high, or the drain pump is blocked. Unplug the washer, clean the drain pump filter, and make sure the hose is not kinked and is no higher than about 3 feet (1 m).
E:30 / -10 or -20 (faucet icon) Listed by Bosch on its US washer page; shown with a faucet icon, which points to a water supply problem. Open the water taps fully, straighten the hoses and clean the inlet screens. If the code returns, call Bosch service.
E:36 / -10, -25, -26 Drain pump blocked; on some models also low water pressure or a blocked inlet filter. Unplug the washer and clean the drain pump filter. Check that the taps are open and the inlet hose is not kinked.
E:35 / -10 Water in the base or the washer is leaking.
Call a technician
Turn off the water taps, unplug the washer and call a technician.
E:10 / -00, -10, -20 Models with i-DOS automatic dosing: the dosing pump is blocked. Turn the washer off, clean the dosing pump unit as the manual describes and restart. You can wash with i-DOS turned off and dose by hand until it is fixed.
E:60 / -2B Spin stopped because the load is unevenly distributed. Redistribute the laundry, mixing large and small items, and restart.
H:32 Hint code: the drum is unbalanced, so spinning stopped. Pause, untangle the laundry, spread it evenly and continue.
E:38 / -25, -26 Listed by Bosch on its US washer page. Repair references link E38 to a blocked pressure chamber. Control-detected fault; the manufacturer lists the code without a public meaning. Reset by unplugging for 5 minutes; if it returns, call a technician.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
E:00 <-> -18 / E:00 <-> -23 Listed by Bosch on its US washer page without a published meaning. On Bosch washers, 18 is the drain fault and 23 the AquaStop leak fault, so check those first (see E18 and E23 above).
Call a technician
Clean the drain pump filter and check for water under the washer. If the code returns, call a technician.
E34 / F34 / F29 Grouped by Bosch with the door code (E34/F34) and the water supply code (F29). For E34/F34, close the door firmly. For F29, open the taps fully and check the inlet hose and screen.
E33 / F33 / E80 / E:92 / -01 Listed by Bosch on its US washer page without a published meaning; repair references tie E90-E92 to a software or board fault. Control-detected fault; the manufacturer lists the code without a public meaning. Reset by unplugging for 5 minutes; if it returns, call a technician.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
H9E (with tap icon) Listed by Bosch on its US washer page with a water tap icon, which points to a water supply problem. Check that the taps are open and the inlet hoses and screens are clear.
E29 / E37 (some models) Commonly reported: water pressure too low (E29) or an overfill (E37).
Call a technician
For E29, open the tap fully and clean the inlet screen. For E37, turn off the water and call a technician.
E42 / E43 / E44 / E47 / E48 (some models) Commonly reported door lock faults: the door will not unlock (E42, E43), the door was opened during a cycle (E44), or a door lock electronics failure (E47, E48).
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
E45 Commonly reported: communication error in the control module.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
E50 / F50 / F43 Commonly reported motor faults: a motor speed sensor (tachometer) or motor driver error (E50/F50), or the drum is not turning (F43).
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
Er:04 (Nexxt) The door lock relay will not activate.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
Er:22 (Nexxt) Electrical power supply problem.
Call a technician
Plug the washer directly into its own outlet. If the code persists, have the supply checked and call a technician.
Er:25 (Nexxt) The door lock is blocked.
Call a technician
Make sure nothing is caught in the door, close it firmly and restart. If it repeats, call a technician.
CL Child lock is on. Not a fault. On many models, press and hold Start (or the key your manual shows) for about 5 seconds to turn it off.

What we actually find on Bosch washers in the Denver area

The codes above come from Bosch’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 9 Bosch washer service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The washer repairs we do most often (all brands)

Our notes on Bosch washers are too thin to rank by brand alone, so here is what we found across all 1238 washer calls in our records:

  1. Control or display board: 108 calls
  2. Drain pump: 74 calls
  3. Shock absorbers or suspension: 57 calls
  4. Water inlet valve: 41 calls
  5. Door or lid lock: 28 calls
  6. Door boot seal: 27 calls
  7. Drive belt or coupler: 23 calls

Recent Bosch washer calls

  • Boulder (80303), September 2026: Bosch washer door or lid problem. Repair: door or lid lock replaced (00438026).
  • Lakewood (80227), August 2026: Bosch washer not draining. Repair: drain pump replaced.

Bosch washer repairs from $200. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Bosch washer error codes

Video by Bosch Home UK and Ireland

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • Across all 1238 washer calls in our records (all brands), the repairs we do most often: control or display board (108 calls), drain pump (74) and shock absorbers or suspension (57).
  • Recent call: Boulder (80303), September 2026: Bosch washer door or lid problem. Repair: door or lid lock replaced (00438026).

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. Unplug the washer and turn off both water taps before any hands-on check.
  2. Make sure the taps are fully open and the inlet hoses are not kinked.
  3. Clean the screens in the inlet hose connections.
  4. Drain and clean the pump filter behind the service flap. Water may be hot, so let it cool first.
  5. Close the door firmly and check the seal for caught clothing.
  6. Use only HE detergent and measure it; Denver's hard water does not call for extra.
  7. For other codes, unplug for a few minutes, then restart once.

When to call a technician

  • E23/F23 or Er:17 appears, or you see water under the washer.
  • The washer will not drain after the pump filter and hose are clear.
  • Heating, sensor or communication codes come back after a reset.
  • The washer keeps filling while unplugged.
  • The door will not lock or unlock.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

How do I reset a Bosch washer error code?

Turn the washer off, wait at least 5 seconds (or unplug it for a few minutes), then turn it on and start the cycle again. If the same code returns, the fault needs to be fixed.

What does F18 or E18 mean on a Bosch washer?

The washer is not draining. Usually the drain pump filter is clogged or the drain hose is kinked. Clean the pump filter behind the service flap and straighten the hose.

What does F23 or E23 mean on a Bosch washer?

The AquaStop leak protection was triggered, which usually means water is leaking. Turn off the water tap right away and do not use the washer until it is repaired.

Are E codes and F codes the same on Bosch washers?

In most cases, yes. Bosch lists pairs such as E17 or F17 with the same meaning. Older Nexxt washers use a different Er code system.

Sources: bosch-home.com, bosch-home.com, bosch-home.com, bosch-home.com, bosch-home.com, c.searspartsdirect.com, searspartsdirect.com, bosch-home.com, media3.bosch-home.com, media3.bosch-home.com, coolblue.nl, domex-uk.co.uk, removeandreplace.com. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229
Call Now Book Online