Dacor has two code eras. Older Dacor ovens and ranges show F0 to F8: F3 and F4 are the oven sensor, F2 is overheating, F7 and F8 are the door lock, and F0, F1 and F6 are the keypad or control. Current Dacor ovens show C-codes instead, for example C-d1 (lock out of position) and C-20 or C-21 (sensor open or shorted). Start with a 30-second power reset; if the code returns, call for service.
Dacor’s older electronic oven control and its current Samsung-era controls use completely different codes, so first check whether your display shows an F or a C. The F-code meanings come from Sears PartsDirect, PartSelect and AppliancePartsPros; the C-codes come from Dacor manuals plus one parts reference. Some Dacor wall ovens also use three-character codes such as C01 or C42, listed separately. Turn off the breaker before any check, and on gas or dual-fuel units close the gas supply too.
Dacor oven codes by generation
Older F-code controls
| Code | Dacor meaning | Recommended action |
|---|---|---|
F0 |
A function key is stuck, often Clock. | Press it firmly and dry the panel; a key that stays stuck means a new key panel. |
F1 |
Watchdog fault, or an element relay stuck on the control board. Technician |
Cancel and wait 30 seconds; if it stays, 3 minutes without power. |
F2 |
Runaway heat from a stuck relay, failed sensor or shorted heating circuit. Technician |
Cancel, breaker off. Switch off, let it cool fully, and leave it off until inspected. |
F3 / F4 |
RTD oven sensor shorted (F3) or open (F4). Technician |
Breaker reset; a repeat means the sensor or its harness. |
F6 |
Control memory (EEPROM) error; often only the clock and timer still work. Technician |
3 minutes without power; a repeat means a new board. |
F7 / F8 |
Lock engaged while too hot or lock circuit fault (F7); door locking switch (F8). Technician |
Cool down completely, reset at the breaker. |
Current C-code controls
| Code | Dacor meaning | Recommended action |
|---|---|---|
C-d1 |
Lock is out of position. | Press OFF and restart; then 30 seconds without power. Still showing? Book. |
C-F0, C-F2 |
Communication interrupted between main and sub boards (C-F0) or main board and touch panel (C-F2). Technician |
OFF, then 30 seconds without power. If it returns, schedule a repair. |
C-20, C-21 |
Oven sensor open (C-20) or shorted (C-21) while running. Technician |
OFF, then 30 seconds without power. If it returns, schedule a repair. |
C-23 |
Cavity temperature abnormally high. Technician |
Switch off, let it cool fully, and leave it off until inspected. |
C-30 |
Probe sensor shorted. | Remove the probe, dry the jack, reset. |
C-31, C-70, C-72 |
Board temperature sensor open (C-31) or shorted (C-70), board running too hot (C-72). Technician |
Make sure the cooling vents are clear, let it cool, reset. |
C-A2 |
Steam-assist ovens: steam sensor open. Technician |
OFF, then 30 seconds without power. If it returns, schedule a repair. |
Three-character codes on some Dacor wall ovens
| Code | Dacor meaning | Recommended action |
|---|---|---|
C01 |
Shorted key on the panel. Technician |
Dry the panel and reset. |
C23, C33 / C24, C34 / C25, C35 |
Ambient temperature over limit (C23, C33), sensor open (C24, C34) or shorted (C25, C35). Technician |
Switch off, let it cool fully, and leave it off until inspected. |
C41, C42, C44 |
Board reference reading (C41), memory checksum (C42), program memory checksum (C44). Technician |
OFF, then 30 seconds without power. If it returns, schedule a repair. |
C76 |
Oven type set wrong (single vs double), usually after a control swap. Technician |
The control needs to be configured by a technician. |
What we actually find on Dacor ovens in the Denver area
The codes above come from Dacor’s own documentation. This section shows what our technicians found once they opened the machine. Since 2024 we have handled 5 Dacor oven service calls across the Denver metro and Boulder County. Every number here comes from our own job records.
The oven repairs we do most often (all brands)
Our notes on Dacor ovens are too thin to rank by brand alone, so here is what we found across all 645 oven calls in our records:
- Control board: 54 calls
- Igniter: 45 calls
- Bake or broil element: 26 calls
- Surface element or burner switch: 20 calls
- Wiring: 16 calls
- Convection fan: 15 calls
- Temperature sensor: 13 calls
Oven repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.
Source: The Appliance Team service records, 2024–2026. Customer details removed.
Video: Dacor oven error codes
Video by Gilbo’s DIY
What we see on Denver calls
- An error code points to the system that reported the fault, not always to the part that failed.
- Across all 645 oven calls in our records (all brands), the repairs we do most often: control board (54 calls), igniter (45) and bake or broil element (26).
Don’t want to do it yourself? Call 720-230-1229.
What you can do safely
- Write down the full code, including everything after “C-“.
- Press Cancel or OFF, then cut power at the breaker for 30 seconds (3 minutes for F-code ovens).
- Clean and dry the touch panel.
- For probe codes, remove the probe and dry the socket.
- Gas or dual fuel and you smell gas: leave and call the gas utility.
Dacor oven: call for service if
- F2, C-23 or any over-temperature code appears.
- F3, F4, C-20 or C-21 returns after the reset.
- The door stays locked once the oven is cold.
- Board or memory codes repeat, or the oven trips its breaker.
How to prevent this
Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:
Dacor oven code FAQ
How do I reset a Dacor oven code?
Press OFF or Cancel, then turn the breaker off for at least 30 seconds (3 minutes on older F-code models).
What does F4 mean on a Dacor?
The RTD temperature sensor reads open. If a reset does not clear it, the sensor or its wiring needs replacing.
What does C-d1 mean?
The door lock is out of position. Restart the oven; if it persists after a power reset, book a repair.
Why do older Dacors show F codes and newer ones C codes?
Dacor changed control platforms. The two systems are unrelated, so use the table for your code style.
Sources: searspartsdirect.com, partselect.com, appliancepartspros.com, manualslib.com. Codes and meanings can vary by model; check your owner’s manual.