JennAir Oven Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

On a current JennAir wall oven or range, read the first digit of the code: F1 is the oven control, F2 the keypad, F3 a temperature sensor or the meat probe, F5 the door lock, F6 overheating or lost board communication, F8 the cooling fan, and F9E0 incorrect power wiring. Older JennAir ovens show a single F code instead, and on those F2 is the overheat warning, F3 or F4 the sensor and F9 the latch. A code that survives a one-minute breaker reset needs a service visit.

JennAir has gone through several oven control generations. Today’s built-in wall ovens and ranges share Whirlpool’s two-part F#E# system. Before that, JennAir used single-character F codes, and even those changed meaning partway through, so the same “F3” can mean two different things depending on age. A few models in between show slash codes such as 3d/11. Find which style your display uses, then look in the matching table. Our sources are JennAir tech sheets, Whirlpool’s help pages and parts catalogs.

JennAir oven codes by control generation

Current two-part codes: controls and keypad

Code Diagnosis Next move
F1E0 The user interface (glass touch panel) has failed.
Technician
Breaker off one minute; service if it comes back.
F1E1 Error inside the appliance manager, the main oven control. Double ovens may involve both controls.
Technician
Breaker off one minute; service if it comes back.
F2E0 Keypad is not connected.
Technician
Usually a ribbon cable behind the panel.
F2E1 One key reads as shorted or held.
Technician
Dry the glass and press Cancel. If a reset does not help, the keypad gets replaced.
F6E0, F6E6, F6E9 Lost communication: interface to control (E0), upper or single oven control (E6), lower oven control (E9).
Technician
Breaker off one minute; service if it comes back.
F6E4 The appliance manager reports a status mismatch.
Technician
Breaker off one minute; service if it comes back.
F8EA Touch panel or its wiring.
Technician
Breaker off one minute; service if it comes back.

Current two-part codes: heat, sensors and probe

Code Diagnosis Next move
F3E0 Upper or single-oven RTD sensor is open or shorted.
Technician
One reset, then the sensor and harness get tested with a meter.
F3E1 Lower-oven RTD sensor is open or shorted.
Technician
Same test, lower cavity.
F3E3 Meat probe or its jack is shorted. Push the probe in until it seats, or cook without it. A persistent code means the jack.
F6E1, F6E3 Over-temperature in the upper or single oven (E1) or the lower oven (E3).
Technician
Breaker off and do not cook. A welded relay or bad sensor can keep elements on.
F8E0 to F8E3 Commonly listed as cooling fan speed or circuit faults.
Technician
Skip self-clean and long roasts until the fan is checked.
F8E4 Commonly listed as the exhaust air sensor.
Technician
Breaker off one minute; service if it comes back.

Current two-part codes: door lock and wiring

Code Diagnosis Next move
F5E0, F5E1 Upper or single oven: door switch and latch switch disagree (E0), or the latch motor does not move (E1).
Technician
Let it cool all the way; never pry the door. Then a one-minute reset.
F5E3, F5E4 The same two latch faults on the lower oven.
Technician
As above.
F9E0 The oven is wired incorrectly at the junction box.
Technician
Do not keep resetting. The installer or an electrician must correct the connection.

Older single-character codes

Code Diagnosis Next move
F0 Function key stuck. Breaker off one minute; service if it comes back.
F1 Earlier controls: bad touch pad or board. Later single-code controls: an element relay energized with only the clock on.
Technician
Treat as a heat risk: breaker off until inspected.
F2 Overheat: roughly 600 °F in Bake or 900 °F in Clean on later controls.
Technician
Breaker off; do not use.
F3 Earlier controls: sensor open or shorted. Later controls: cooling fan running with nothing selected (sensor or harness).
Technician
Sensor and harness test.
F4 Temperature sensor open or shorted.
Technician
Sensor test.
F5 Watchdog or hardware conflict on the board, or element relays disabled during a cook mode.
Technician
Breaker off one minute; service if it comes back.
F7 A key held or shorted (32 seconds on later controls).
Technician
Breaker off one minute; service if it comes back.
F8 Analog-to-digital fault on the board, or a shorted probe reading over about 250 °F.
Technician
Remove the probe and retry.
F9 Door latch or the lock safety circuit on the power relay board.
Technician
Cool down, reset, do not force the door.
FF, F / FC, FR Invalid temperature on the relay board (FF), boards not communicating (F, FC), fault in the second oven (FR).
Technician
Breaker off one minute; service if it comes back.

Slash-style codes and normal messages

Code Diagnosis Next move
1C/1C, 1C/2C Keypad: stuck or defective (1C/1C), harness unplugged (1C/2C).
Technician
Breaker off one minute; service if it comes back.
1C/31 through 1C/82 Control board, Cancel circuit or communication.
Technician
Breaker off one minute; service if it comes back.
1d/11, 1d/12; 1d/21, 1d/22 Too hot in Bake/Broil (1d/1x) or in Clean (1d/2x).
Technician
Breaker off and wait for service.
3d/11 to 3d/51 Temperature sensor circuit.
Technician
Sensor test.
4d/11 to 4d/52; 9d/11 to 9d/62 Door switch versus lock switch disagreement, latch or wiring (4d); lock assembly (9d, with 9d/31 and 9d/32 during Clean).
Technician
Cool down, reset, do not force the door.
LOC, Lock Control lock is on. Not a fault. Unlock as your manual describes.
PF, blinking time Power was interrupted. Press Cancel and set the clock.

What we actually find on JennAir ovens in the Denver area

The codes above come from JennAir’s own documentation. This section shows what our technicians found once they opened the machine. Since 2024 we have handled 6 JennAir oven service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

Code Our calls What we found
F1 1 Control board.
F3 1 Control board.

The oven repairs we do most often (all brands)

Our notes on JennAir ovens are too thin to rank by brand alone, so here is what we found across all 645 oven calls in our records:

  1. Control board: 54 calls
  2. Igniter: 45 calls
  3. Bake or broil element: 26 calls
  4. Surface element or burner switch: 20 calls
  5. Wiring: 16 calls
  6. Convection fan: 15 calls
  7. Temperature sensor: 13 calls

Recent JennAir oven calls

  • Littleton (80128), August 2026: JennAir oven not starting. Repair: convection fan replaced (WPW10273666).
  • Westminster (80030), June 2026: JennAir oven showing F1. Repair: control board replaced.

Oven repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2024–2026. Customer details removed.

Video: JennAir oven control board repair

Video by AppliancePartsPros

What we see on Denver calls

  • The video shows a control board repair. It is the most common oven repair on our calls (all brands).
  • Across all 645 oven calls in our records (all brands), the repairs we do most often: control board (54 calls), igniter (45) and bake or broil element (26).
  • Recent call: Littleton (80128), August 2026: JennAir oven not starting. Repair: convection fan replaced (WPW10273666).

Don’t want to do it yourself? Call 720-230-1229.

What to do in the first ten minutes

  1. Photograph the display so you have the exact code and its style (F3E0, F3 or 3d/11).
  2. Switch the oven breaker off for about a minute, back on, and watch the panel for another minute.
  3. If the code mentions heat or the oven smells hot, leave the breaker off.
  4. For probe codes, remove the probe; for keypad codes, dry the glass.
  5. Gas JennAir: never loosen gas fittings. Smell gas? Leave the house and call the gas utility.

Call us when

  • The code is back after the breaker reset.
  • Any overheat code appears, or elements glow with the oven off.
  • The door stays locked after the oven is cold.
  • F9E0 shows on a new install, or you notice gas or a burning smell.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

JennAir oven code FAQ

How do I clear a JennAir oven code?

Turn the oven’s breaker off for about a minute and back on. A glitch clears; a real fault returns within minutes or the next time you bake.

What does F2E1 mean on a JennAir wall oven?

The control sees a key that is shorted or stuck. Moisture on the glass can cause it once, but a repeat usually needs a new keypad.

What does F3E0 mean?

The upper or single-oven temperature sensor reads open or shorted, so the oven cannot regulate heat. The sensor is a common replacement part.

Why does F2 mean something different on my older JennAir?

Older single-code controls used F2 for overheating, while current two-part codes use F2 for the keypad. Check which format your display shows.

Sources: nelihome.com, partselect.com, appliancepartspros.com, producthelp.whirlpool.com, appliancepartspros.com, producthelp.whirlpool.com, producthelp.whirlpool.com, whirlpool.com. Codes and meanings can vary by model; check your owner’s manual.

720-230-1229
720-230-1229
Call Now Book Online