LG Oven & Range Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

On LG ranges, F1, F2, F4 and F5 point to an oven temperature sensor; F3 to a stuck touch key; F6 or F16 to an oven that ran above 650°F; F9 or F19 to an oven that is not heating; and F10 or F20 to the door lock. Press Clear/Off and reset the breaker for 30 seconds; if the code comes back, the range needs service. PF, HS and Sb are status messages, not faults.

LG ranges show F codes for oven faults, CF codes for induction cooktop faults, and flashing numbers on some cooktop displays. On double-oven models, the lower number usually refers to the upper oven and the higher number (F16, F19, F20) to the lower oven. This list combines LG's own support pages with codes documented by LG parts and repair references. Codes vary by model, so check your owner's manual if yours is not listed.

LG Oven & Range error codes and what they mean

Code What it means What to try
F1 / F2 (also F1F4 / F2F5) Upper (or main) oven temperature sensor reads open (F1) or shorted (F2) for over a minute during cooking.
Call a technician
Press Clear/Off and try again. If it returns, reset the breaker for 30 seconds. If it still returns, a technician should test the sensor and wiring.
F3 Touch pad key error: one or more keys read as pressed for over 60 seconds.
Call a technician
Wipe the panel dry and make sure nothing rests on it. Reset the breaker for 30 seconds. If F3 returns, request service.
F4 / F5 Lower oven (or, on some models, main oven or warming drawer) temperature sensor reads open (F4) or shorted (F5).
Call a technician
Reset power at the breaker once. If the code comes back, a technician should test the sensor and its wiring.
F6 / F16 (F6F16) Oven ran above 650°F for 2 minutes outside self-clean: upper oven (F6) or lower oven (F16).
Call a technician
Turn the oven off at the breaker and let it cool. Do not use it until it is checked; a sensor, relay or control fault can cause runaway heat.
F7 Depending on model: upper convection fan not detected running, or (on some older LG electric ranges) the oven did not reach 150°F within 5 minutes of preheating.
Call a technician
Turn the range off, then switch the breaker off for 30 seconds and back on. If the code returns, request service.
F8 / F18 Meat probe sensor shorted: upper or right oven (F8) or lower oven (F18). Unplug the probe, check it for damage and try cooking without it. If the code stays, request service.
F9 / F19 (F9F19) Oven is not heating: it failed to warm up enough within about 5 minutes of preheating with the door closed. F9 is the upper or main oven, F19 the lower oven.
Call a technician
Press Clear/Off and reset power for 3 to 5 minutes. On gas models, confirm the main and oven gas shut-off valves are open. If the code returns, request service.
F10 / F20 (F10F20) Door lock system failure: upper or main oven (F10) or lower oven (F20).
Call a technician
Let the oven cool completely, then reset power at the breaker. Do not force the door. If the code returns or the door stays locked, request service.
F11 Communication error between the oven and cooktop control boards.
Call a technician
Turn the range off, then switch the breaker off for 30 seconds and back on. If the code returns, request service.
F17 Convection fan error (on some models, the lower oven convection fan).
Call a technician
Turn the range off, then switch the breaker off for 30 seconds and back on. If the code returns, request service.
F21 / F22 / F24 / F25 Steam sensor failure on steam-equipped models (F24 open, F25 shorted).
Call a technician
Turn the range off, then switch the breaker off for 30 seconds and back on. If the code returns, request service.
F27 Cooling fan stalled or locked during self-clean.
Call a technician
Turn the range off, then switch the breaker off for 30 seconds and back on. If the code returns, request service.
F33 / F34 Front induction burner temperature sensor error.
Call a technician
Turn the range off, then switch the breaker off for 30 seconds and back on. If the code returns, request service.
F36 Transistor error in the cooktop electronics.
Call a technician
Turn the range off, then switch the breaker off for 30 seconds and back on. If the code returns, request service.
F38 Communication error between the main board and the induction inverter.
Call a technician
Turn the range off, then switch the breaker off for 30 seconds and back on. If the code returns, request service.
F42 Voltage error.
Call a technician
Reset the breaker for 30 seconds. If it returns, have the power supply and range checked.
F45 / F46 Fan error.
Call a technician
Turn the range off, then switch the breaker off for 30 seconds and back on. If the code returns, request service.
F51 / F52 / F56 / F59 Griddle errors: sensor fault (F51), sensor short (F52), heating error (F56) or griddle not heating properly (F59).
Call a technician
Turn the range off, then switch the breaker off for 30 seconds and back on. If the code returns, request service.
F62 / F69 Sous vide errors: temperature sensor fault (F62) or not heating properly (F69).
Call a technician
Turn the range off, then switch the breaker off for 30 seconds and back on. If the code returns, request service.
CF1 / CF2 / CF3 / CF4 Induction cooktop top sensor open or shorted: left front, left rear, right front or right rear.
Call a technician
Turn the range off, then switch the breaker off for 30 seconds and back on. If the code returns, request service.
CF5 / CF6 Induction cooktop left or right IGBT (power module) sensor open or shorted.
Call a technician
Turn the range off, then switch the breaker off for 30 seconds and back on. If the code returns, request service.
CF7 / CF8 / CFA Induction cooktop communication error at the left or right module; CFA is listed as over current or a communication error depending on the source.
Call a technician
Turn the range off, then switch the breaker off for 30 seconds and back on. If the code returns, request service.
CFC Over voltage detected at the cooktop.
Call a technician
Reset the breaker. If it returns, have an electrician check the supply voltage, then request service.
CFF Cooktop box (cooling) fan not working properly.
Call a technician
Turn the range off, then switch the breaker off for 30 seconds and back on. If the code returns, request service.
Cooktop flashing 1, 2 or 3 Cooktop thermistor (temperature sensor) error.
Call a technician
Press Power On/Off. If it returns, reset the breaker for 30 seconds; if it persists, request service.
Cooktop flashing 4 Water or metal objects have been on the touch pads for a long time. Clean and dry the cooktop surface, remove any objects from the touch pads, and press Power On/Off.
Cooktop flashing 5 Display error.
Call a technician
Press Power On/Off. If it returns, reset the breaker for 30 seconds; if it persists, request service.
Cooktop flashing 6 Low voltage.
Call a technician
Have a qualified electrician check the power supply.
PF Power was interrupted. Press Clear/Off and reset the clock. If PF keeps returning without outages, request service.
HS / H5 Hot surface: the cooktop is above about 150°F. Not a fault. Let it cool. If it stays on with a cold cooktop, reset power; if it persists, request service.
Sb / 5b Sabbath mode is on. Not a fault. Exit Sabbath mode using the steps in your owner's manual (on many models, press and hold Clock for 3 seconds).
Child Lock / Clean Controls are locked, or a self-clean or EasyClean cycle is running. Not a fault. Hold the lock button for 3 seconds to unlock, or wait for the cleaning cycle to finish.

What we actually find on LG ovens in the Denver area

The codes above come from LG’s own documentation. This section shows what our technicians found once they opened the machine. Since 2024 we have handled 31 LG oven service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The oven repairs we do most often (all brands)

Our notes on LG ovens are too thin to rank by brand alone, so here is what we found across all 645 oven calls in our records:

  1. Control board: 54 calls
  2. Igniter: 45 calls
  3. Bake or broil element: 26 calls
  4. Surface element or burner switch: 20 calls
  5. Wiring: 16 calls
  6. Convection fan: 15 calls
  7. Temperature sensor: 13 calls

Recent LG oven calls

  • Parker (80134), October 2025: LG oven making noise. Diagnosis: surface element or burner switch.
  • Denver metro, June 2025: LG oven not starting. Repair: convection fan replaced (EBR80595407).
  • Arvada (80005), March 2025: LG oven not starting. Repair: control board replaced (EBR80595401).

LG oven repairs from $270. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2024–2026. Customer details removed.

Video: LG oven error codes

Video by Parts Dr

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • Across all 645 oven calls in our records (all brands), the repairs we do most often: control board (54 calls), igniter (45) and bake or broil element (26).
  • Recent call: Arvada (80005), March 2025: LG oven not starting. Repair: control board replaced (EBR80595401).

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. Press Clear/Off, then try the function again.
  2. If the code returns, turn off the circuit breaker for 30 seconds (LG suggests up to 5 minutes for no-heat codes), then turn it back on.
  3. Wipe the control panel and cooktop dry and remove anything resting on the touch pads.
  4. Unplug the meat probe for F8 or F18.
  5. On gas models with F9 or F19, make sure the gas shut-off valves are open. Never work on gas lines yourself.
  6. Let the oven cool fully before dealing with a locked door.

When to call a technician

  • Any F or CF code returns after a breaker reset.
  • The oven overheats (F6, F16) or keeps heating when off.
  • The oven will not heat (F9, F19) with the gas supply on.
  • The door will not lock or unlock (F10, F20).
  • You smell gas or burning.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

How do I reset an error code on my LG range?

Press Clear/Off, then turn off the range's circuit breaker for 30 seconds and back on. If the code clears and stays gone, the range is fine to use; if it returns, LG recommends service.

What does F9 mean on an LG oven?

F9 means the oven did not heat up enough during the first 5 minutes of preheating. A failed element or igniter, a relay or control fault, or a closed gas valve on gas models are common causes.

What does F3 mean on an LG range?

F3 means a touch key has read as pressed for over 60 seconds. Dry the panel and reset power; if it returns, the touch panel or control usually needs replacing.

What is the difference between F10 and F20 on an LG double oven?

Both are door lock failures. F10 is the upper oven door lock and F20 is the lower oven door lock.

Sources: lg.com, lg.com, lg.com, lgparts.com, midea.encompass.com, manuals.plus, homeserve.com. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229
Call Now Book Online