KitchenAid Oven Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

KitchenAid wall ovens and ranges use a two-part code. The F number names the system (F1 control, F2 keypad, F3 sensor or probe, F5 door lock, F6 overheat or communication, F8 cooling fan, F9 power wiring) and the E number narrows it down. The only reset an owner can do is to switch the breaker off for a minute and back on. If the code returns, book a technician.

KitchenAid ranges and wall ovens are engineered by Whirlpool, and on double wall ovens certain E numbers belong to the lower cavity, such as F3E1 or F5E3. Some KitchenAid slide-in ranges use a slash format instead (1C, 1d, 3d, 4d, 9d), and older ovens show a single F with one digit. We compiled this page from KitchenAid’s own help pages, Whirlpool service literature, and the parts catalogs at Sears PartsDirect and PartSelect. The table for each code family is below, with an honest answer on whether it is a homeowner fix.

KitchenAid oven fault codes, family by family

F1: oven control board

Code KitchenAid fault Can you fix it?
F1E0 Interface or control memory (EEPROM) fault.
Technician
No. Power-cycle once at the breaker; a return means a repair.
F1E1 Electronic oven control failed; some references cite an EEPROM checksum error.
Technician
No. Power-cycle once at the breaker; a return means a repair.
F1E2 to F1E9 Board-level faults: A/D conversion, harness or model ID mismatch, calibration drift, latch signal mismatch, software error.
Technician
No. Power-cycle once at the breaker; a return means a repair.

F2: keypad and Cancel key

Code KitchenAid fault Can you fix it?
F2E0 Panel not responding, keypad disconnected or shorted.
Technician
No. Power-cycle once at the breaker; a return means a repair.
F2E1 A button is stuck or defective, or the touch pad cable came loose.
Technician
Partly. Dry the glass and press Cancel; if it returns, the keypad is replaced.
F2E2, F2E5, F2E6 Cancel key error or Cancel circuit open.
Technician
No. Power-cycle once at the breaker; a return means a repair.

F3 and F4: temperature sensors and meat probe

Code KitchenAid fault Can you fix it?
F3E0 Upper or single-oven sensor is bad, open or shorted.
Technician
No. After one reset, the sensor and harness are tested.
F3E1 Lower oven sensor bad (on single ovens, sensor shorted).
Technician
No, same test.
F3E3, F4E1 Meat probe or its socket is shorted; a pinched cord or moisture in the socket are typical. Often yes: seat the probe firmly, or cook without it. A lasting code means the socket.
F3E9 Listed by KitchenAid with no public definition; neighboring F3 codes are sensors.
Technician
No. Power-cycle once at the breaker; a return means a repair.

F5 and F7: door lock

Code KitchenAid fault Can you fix it?
F5E0 Upper or main oven: door switch and lock switch disagree.
Technician
No. Wait until the oven is cold, power-cycle, and never pry the door.
F5E1 Upper or main oven lock assembly does not work.
Technician
No. Wait until the oven is cold, power-cycle, and never pry the door.
F5E3, F5E4 Lower oven: switch disagreement (E3) or latch not moving (E4).
Technician
No. Wait until the oven is cold, power-cycle, and never pry the door.
F7E1 Commonly reported as a bad common wire between the latch and door switches.
Technician
No. Wait until the oven is cold, power-cycle, and never pry the door.

F6: overheating and board communication

Code KitchenAid fault Can you fix it?
F6E1, F6E2, F6E3 Overheat in Bake or Broil (E1), in Clean (E2), or in the lower oven (E3).
Technician
No. Leave the breaker off and do not cook until it is inspected.
F6E0 Panel and oven control are not communicating.
Technician
No. Power-cycle once at the breaker; a return means a repair.
F6E4, F6E5 Wrong panel or board installed (E4), or a new board not programmed for this oven size (E5). Usually right after a repair.
Technician
No. Whoever installed the part should correct it.
F6E6, F6E9 Commonly reported on wall ovens: upper or main (E6) or lower (E9) control lost communication.
Technician
No. Power-cycle once at the breaker; a return means a repair.

F8 and F9: cooling fan and power

Code KitchenAid fault Can you fix it?
F8E0 to F8E3 Cooling fan too slow (E0) or too fast (E2), or a fan or wiring fault (E1, E3).
Technician
No. Keep vents clear and skip self-clean and long bakes until the fan is checked.
F9E0 Range or house power wired incorrectly.
Technician
No. On a new install, the installer or an electrician checks the connection.

Slide-in slash codes, older single codes and normal messages

Code KitchenAid fault Can you fix it?
1C/1C, 1C/2C; 1C/31 to 1C/82 Keypad stuck or unplugged (1C/1C, 1C/2C); control board, Cancel circuit or communication (other 1C).
Technician
No. Power-cycle once at the breaker; a return means a repair.
1d/11 to 1d/22 Too hot in Bake/Broil (1d/1x) or Clean (1d/2x).
Technician
No. Leave the breaker off and do not cook until it is inspected.
3d/11 to 3d/51 Oven sensor circuit.
Technician
No. Power-cycle once at the breaker; a return means a repair.
4d/11 to 4d/52, 9d/11 to 9d/62 Door and lock switch disagreement or latch wiring (4d); lock assembly, including 9d/31 and 9d/32 during Clean (9d).
Technician
No. Wait until the oven is cold, power-cycle, and never pry the door.
F0, F1, F5, F8 (older) Board failure on older controls (F5 watchdog conflict, F8 A/D error). On some newer controls F0 just means no stored faults.
Technician
No. Power-cycle once at the breaker; a return means a repair.
F2 (older) Oven too hot.
Technician
No. Leave the breaker off and do not cook until it is inspected.
F3, F4 (older) Sensor open or shorted; references disagree on which is which.
Technician
No. Power-cycle once at the breaker; a return means a repair.
F7, F9 (older) Function key stuck (F7); door latch or lock switch (F9).
Technician
No. Power-cycle once at the breaker; a return means a repair.
LOC, PF, SAb Control lock on, power interrupted (flashing clock), or Sabbath mode. None are faults. Yes: unlock, press Cancel and reset the clock, or exit Sabbath per your manual.

What we actually find on KitchenAid ovens in the Denver area

The codes above come from KitchenAid’s own documentation. This section shows what our technicians found once they opened the machine. Since 2024 we have handled 21 KitchenAid oven service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The oven repairs we do most often (all brands)

Our notes on KitchenAid ovens are too thin to rank by brand alone, so here is what we found across all 645 oven calls in our records:

  1. Control board: 54 calls
  2. Igniter: 45 calls
  3. Bake or broil element: 26 calls
  4. Surface element or burner switch: 20 calls
  5. Wiring: 16 calls
  6. Convection fan: 15 calls
  7. Temperature sensor: 13 calls

Recent KitchenAid oven calls

  • Lafayette (80026), March 2026: KitchenAid oven making noise. Repair: convection fan replaced (W11200129).
  • Erie (80516), December 2025: KitchenAid oven not starting. Repair: control board replaced (W10759285).
  • Thornton (80602), February 2025: KitchenAid oven not starting. Repair: surface element or burner switch replaced.

KitchenAid oven repairs from $150. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2024–2026. Customer details removed.

Video: KitchenAid oven control board repair

Video by RepairClinic.com

What we see on Denver calls

  • The video shows a control board repair. It is the most common oven repair on our calls (all brands).
  • Across all 645 oven calls in our records (all brands), the repairs we do most often: control board (54 calls), igniter (45) and bake or broil element (26).
  • Recent call: Lafayette (80026), March 2026: KitchenAid oven making noise. Repair: convection fan replaced (W11200129).

Don’t want to do it yourself? Call 720-230-1229.

The one-minute routine

  1. Note the exact code, then turn off the oven’s breaker.
  2. Wait about a minute, turn it back on and watch the display for another minute.
  3. For a probe code, take the probe out; for a keypad code, wipe the glass dry.
  4. After any overheat or lock code, let the oven cool completely first.
  5. Gas range: never touch the gas connection. If you smell gas, get out and call the utility.

When KitchenAid owners should call

  • The code returns after the breaker reset.
  • F6E1 to F6E3, or the oven keeps heating when switched off.
  • The door stays locked with a cold oven.
  • F8 fan codes keep coming back, or you smell burning or gas.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

KitchenAid oven code FAQ

How do I reset my KitchenAid oven?

Turn its breaker off for about a minute and back on. There is no button sequence that clears a real fault.

What does F2E1 mean on a KitchenAid wall oven?

The control sees a stuck or defective key, or a loose touch-pad cable. A repeat usually means a new keypad.

What does F6E1 mean?

The oven overheated during Bake or Broil. Cut power and have it checked before using it again.

What does F5E1 mean?

The upper or main oven’s door lock is not operating. It often shows up around a self-clean cycle.

Sources: producthelp.kitchenaid.com, searspartsdirect.com, searspartsdirect.com, partselect.com, producthelp.whirlpool.com, nelihome.com, producthelp.whirlpool.com, producthelp.whirlpool.com, whirlpool.com. Codes and meanings can vary by model; check your owner’s manual.

720-230-1229
720-230-1229
Call Now Book Online