Kenmore Oven & Range Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

A Kenmore range code only makes sense once you know the factory behind it, which the first three digits of the model number reveal. On Frigidaire-built 790 models F10 is runaway heat, F11 a stuck key, F30/F31 the oven sensor and F90 to F95 the lock. Whirlpool-built 665 and 664 ranges use F3E0 for the sensor and F5E1 for the latch. GE-built 362 ranges use F3/F4 for the sensor and F9 for the lock, while on LG-built 721 Elites F9 means the oven is not heating. A code that returns after a breaker reset needs a technician.

The model tag is inside the door frame, behind the storage drawer or on the back of the range. Read the digits before the dot: 790 = Frigidaire/Electrolux, 664 and 665 = Whirlpool, 911 and 917 = Roper (also Whirlpool), 362 = GE, 721 = LG. The same “F9” means a lock fault on one Kenmore and a heating fault on another, which is why we split the codes by maker below. Our tables follow Sears PartsDirect’s Kenmore charts cross-checked against each manufacturer’s own codes. If your prefix is missing, use our page for the brand that built it.

Kenmore oven and range codes, split by manufacturer

790: Frigidaire-built, two-digit codes

Code On this Kenmore family Response
F1, F3, F9 (older) Sensor or board (F1), sensor (F3), door lock (F9).
Technician
Breaker off 30 seconds; service on repeat.
F10 Temperature running away, past about 600 °F.
Technician
Overheat: breaker off, no cooking until inspected.
F11 A key held or shorted for 30+ seconds.
Technician
Clear anything leaning on the glass, dry it, press Stop.
F12, F13, F15 to F18, nCAL, LinE ERR Control board self-check, ID or memory failures.
Technician
Power-cycle at the breaker; a returning code means service.
F14, F20, F23, F24 Communication: glass panel (F14), interface or surface element control (F20), convection fan speed control (F23, F24).
Technician
Power-cycle at the breaker; a returning code means service.
F30, F31 Oven sensor open (F30) or shorted (F31).
Technician
Sensor test (most read near 1,100 ohms at room temperature).
F60 Some Elite slide-ins: control board running hot; check the cooling fan.
Technician
Clear the vents and let it cool.
F90 to F95 Lock timing faults: unlock too slow (F90), too many unlock tries (F91), door open too long (F92), lock too slow (F93), too many lock tries (F94), motor will not stop (F95).
Technician
Wait for a cold oven, power-cycle, never force the latch.

790: Frigidaire-built, four-digit and glass-touch codes

Code On this Kenmore family Response
F010 Runaway heat over 600 °F.
Technician
Overheat: breaker off, no cooking until inspected.
F011 Stuck key.
Technician
Dry the panel and press Cancel.
F001 to F005, F015 Touch panel (F001, F002, F004, F005, F015) or interface board (F003).
Technician
Power-cycle at the breaker; a returning code means service.
F012, F013, F017, F018, F019 Panel and interface mismatch (F012), interface board (F013), configuration (F017, F019), relay board (F018).
Technician
Power-cycle at the breaker; a returning code means service.
F022 to F029 Communication between the interface board, relay board and touch panel.
Technician
Power-cycle at the breaker; a returning code means service.
F030, F031, F033 Oven sensor (F030, F031) or meat probe shorted or overheated (F033).
Technician
Sensor test (most read near 1,100 ohms at room temperature).
F050, F090, F095, F096 Lock switch unreadable (F050), lock motor not running (F090) or not stopping (F095), door opened during self-clean (F096).
Technician
Wait for a cold oven, power-cycle, never force the latch.
F0 13, F0 15, F5 00, F7 01, F7 02, F7 10 Glass-touch models: interface board (F0 13, F0 15) or communication with the oven control (F5 00) or glass panel (F7 codes).
Technician
Power-cycle at the breaker; a returning code means service.

665 and 664: Whirlpool-built

Code On this Kenmore family Response
F0 No stored fault; appears when Cancel is held 5 seconds. Nothing to do.
F1, F1E0, F1E1, F1E2 Electronic oven control defective.
Technician
Power-cycle at the breaker; a returning code means service.
F2E0, F2E1, F2E5, F2E6 Keypad harness off (E0), stuck key (E1), Cancel key bad (E5, E6).
Technician
Power-cycle at the breaker; a returning code means service.
F3E0, F3E1 Oven sensor open (E0) or shorted (E1).
Technician
Sensor test (most read near 1,100 ohms at room temperature).
F3E2, F3E3 (665), F6E1 (664) Too hot: over 575 °F in Bake (F3E2), over 950 °F in Clean (F3E3), overheat (F6E1).
Technician
Overheat: breaker off, no cooking until inspected.
F4E1 Meat probe shorted. Unplug the probe, inspect it, cook without it.
F5E0, F5E1 Door switch reads open while latch reads locked (E0); latch will not lock or unlock (E1).
Technician
Wait for a cold oven, power-cycle, never force the latch.
F8E0, F8E2 (664) Cooling fan too slow (E0) or too fast (E2).
Technician
Keep vents open, reset once.
F9E0 (664) Cord or house wiring connected wrong.
Technician
Breaker off; installer or electrician corrects it.
1C/1C to 1C/8C Stuck key (1C/1C), keypad harness off (1C/2C), oven control (others).
Technician
Power-cycle at the breaker; a returning code means service.
1d/11 to 1d/22 Too hot in Bake/Broil (1d/1x) or Clean (1d/2x).
Technician
Overheat: breaker off, no cooking until inspected.
3d/11 to 3d/22 Oven sensor.
Technician
Sensor test (most read near 1,100 ohms at room temperature).
4d/11 to 4d/52, 9d/11 to 9d/32 Switch disagreement (4d) or lock assembly (9d; 9d/31, 9d/32 in Clean).
Technician
Wait for a cold oven, power-cycle, never force the latch.

362: GE-built

Code On this Kenmore family Response
F0, F1, F5, F6 Electronic control board.
Technician
Breaker off 3 minutes, then service if it repeats.
F2 Over-temperature.
Technician
Overheat: breaker off, no cooking until inspected.
F3, F4 Sensor open (F3) or shorted (F4).
Technician
Sensor test (most read near 1,100 ohms at room temperature).
F9, FC Door lock.
Technician
Wait for a cold oven, power-cycle, never force the latch.

721: LG-built Kenmore Elite

Code On this Kenmore family Response
F1, F2, F8 Upper oven sensor.
Technician
Sensor test (most read near 1,100 ohms at room temperature).
F4, F5, F18 Lower oven sensor.
Technician
Sensor test (most read near 1,100 ohms at room temperature).
F3 Stuck control key.
Technician
Dry the panel, reset power.
F6, F16 Upper (F6) or lower (F16) oven above 650 °F in Bake or Broil.
Technician
Overheat: breaker off, no cooking until inspected.
F9, F19 Upper (F9) or lower (F19) oven not heating.
Technician
Gas models: confirm the shutoff is open. Then reset once.
F10, F20 Upper (F10) or lower (F20) door lock.
Technician
Wait for a cold oven, power-cycle, never force the latch.
F11 Electric models: oven and cooktop controls not communicating.
Technician
Power-cycle at the breaker; a returning code means service.

What we actually find on Kenmore ovens in the Denver area

The codes above come from Kenmore’s own documentation. This section shows what our technicians found once they opened the machine. Since 2024 we have handled 9 Kenmore oven service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The oven repairs we do most often (all brands)

Our notes on Kenmore ovens are too thin to rank by brand alone, so here is what we found across all 645 oven calls in our records:

  1. Control board: 54 calls
  2. Igniter: 45 calls
  3. Bake or broil element: 26 calls
  4. Surface element or burner switch: 20 calls
  5. Wiring: 16 calls
  6. Convection fan: 15 calls
  7. Temperature sensor: 13 calls

Recent Kenmore oven calls

  • Erie (80516), June 2026: Kenmore oven not starting. Repair: control board replaced.
  • Longmont (80504), December 2025: Kenmore oven making noise. Repair: convection fan replaced.
  • Boulder (80303), January 2025: Kenmore oven not starting. Repair: igniter replaced.

Kenmore oven repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2024–2026. Customer details removed.

Video: Kenmore oven error codes

Video by Parts Dr

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • Across all 645 oven calls in our records (all brands), the repairs we do most often: control board (54 calls), igniter (45) and bake or broil element (26).
  • Recent call: Erie (80516), June 2026: Kenmore oven not starting. Repair: control board replaced.

Don’t want to do it yourself? Call 720-230-1229.

Steps before calling about a Kenmore range

  1. Find the model tag and write down the prefix and the exact code.
  2. Cut power at the breaker for 30 seconds (3 minutes on GE-built 362 models).
  3. Dry the glass for key codes; pull the probe for probe codes.
  4. After an overheat or lock code, wait until the oven is fully cold.
  5. Gas range: never loosen a gas fitting.

Have the range serviced if

  • The code survives the breaker reset.
  • F10, F2, F6 or a 1d code appears, or elements stay hot with the oven off.
  • The door stays locked once cold.
  • F9E0 shows, or you smell gas or burning.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Kenmore oven code FAQ

Who made my Kenmore range?

Look at the model prefix: 790 Frigidaire, 664/665 Whirlpool, 911/917 Roper, 362 GE, 721 LG.

What does F10 mean on a Kenmore oven?

On a Frigidaire-built 790 range it means runaway heat above about 600 °F. Shut off the breaker and have it checked.

What does F9 mean on a Kenmore range?

It depends on the maker: a door lock fault on GE-built and older Frigidaire-built models, but “upper oven not heating” on LG-built 721 Elites.

How do I reset a Kenmore range code?

Turn off its breaker for 30 seconds to 3 minutes and restore power. A code that comes back is a real fault.

Sources: searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, electrical-forensics.com. Codes and meanings can vary by model; check your owner’s manual.

720-230-1229
720-230-1229
Call Now Book Online