Wolf Oven and Range Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

Wolf oven codes vary by series. Door-lock codes such as F1 (L Series) and ERR 01 (legacy dual fuel) mean the latch did not confirm it locked or unlocked, often after the door was slammed or during self-clean. Sensor, relay, element, fan and communication codes need a technician. For almost every Wolf code, the first step is to turn the oven's breaker off for 30 seconds, then retest.

Wolf wall ovens, dual fuel ranges and steam ovens each use their own code format. L Series and legacy dual fuel ranges show short codes such as F1 or COOL FAN, SO24 E Series ovens use E codes, and newer M Series, E Series and dual fuel models show four-character fault codes such as 5021 or 3C20. The list below comes mainly from Wolf's own help articles, with a few commonly reported codes from repair references. Turn off power at the breaker before any hands-on check.

Wolf Oven and Range error codes and what they mean

Code What it means What to try
F1 (L Series wall oven) The door lock or unlock switches were not detected within 60 seconds while the lock motor ran. Slamming the door during heating can trigger it. Reset the breaker, then set the oven to Bake and see if F1 returns. If it does, call for service.
ERR 01 (legacy dual fuel range) Door lock or unlock switch not sensed within 60 seconds. Most often appears during self-clean.
Call a technician
Reset the breaker for 30 seconds and run the oven again. If it returns, call for service.
PF (legacy dual fuel range knob) Power failure, or the oven is too hot for the selected cooking mode. Turn the selector to a cooking mode and back to OFF, open the door to let the oven cool, then reset the breaker for 30 seconds. If PF stays, call for service.
COOL FAN The cooling fan failed, or the switch that monitors it is reporting a failure.
Call a technician
Reset the breaker for 30 seconds. If it returns, stop using the oven and call for service.
COMM ERR Communication lost with the oven controller (L Series built-in ovens and legacy dual fuel ranges).
Call a technician
Reset the breaker. If it returns, call for service.
FUSES WRONG Control configuration settings are incorrect or code protection is disabled. This is not a blown fuse you can replace.
Call a technician
Turn the oven control off. If the message remains, call for service.
Err 00 The range is in diagnostic mode, or the control touch pad has a problem. Reset the breaker for 30 seconds. If it continues, call for service.
07 0 26 (legacy E Series) Oven temperature sensor (RTD) circuit error.
Call a technician
Leave the breaker off for several minutes, then retry. If it persists, call for service.
10 0 0 (legacy E Series) Communications error detected by the user interface module (UIM).
Call a technician
Reset the breaker for 30 seconds. If it returns, call for service.
E02 (SO24 E Series) Relay board problem caused by moisture or electrical interference.
Call a technician
Reset the breaker for 30 seconds and retest. If it returns, call for service.
E05 (SO24 E Series) Firmware error in the control.
Call a technician
Reset the breaker for 30 seconds. If it returns, call for service.
E17 (SO24 E Series) Food probe fault: a short in the probe or its wiring, the probe tip not inserted in food, or moisture in the probe socket. Make sure the probe is fully inserted in the food and the socket is dry, then reset the breaker. If it returns, call for service.
E26 (SO24 E Series) Climate sensor fault: a loose connection or break in the sensor wiring, or a blocked exhaust or sensor duct.
Call a technician
Reset the breaker for 30 seconds. If it returns, call for service.
E37 (SO24 E Series) Faulty control board.
Call a technician
Reset the breaker for 30 seconds. If it returns, call for service.
E49 (SO24 E Series) A button is jammed or blocked, or there is moisture on the control board. Make sure nothing is pressing on the controls and the panel is dry, then reset the breaker. If it returns, call for service.
E62 (SO24 E Series) Under-voltage in the power supply, or an electrical calibration error.
Call a technician
Reset the breaker for 30 seconds. If it keeps returning, have the home's voltage checked and call for service.
E81 (SO24 E Series) Relay not calibrated.
Call a technician
Reset the breaker for 30 seconds. If it returns, call for service.
0021 / 0222 / 0422 / 0521 (M Series) Heating element relay or element drive circuit shorted: bake element relay (0021), lower bake element (0222), lower left convection element relay (0422), upper broil element (0521).
Call a technician
Turn the oven off at the breaker and call for service.
4021 / 4022 Bake element load missing: the control does not see the bake element drawing power (E Series ovens and dual fuel ranges).
Call a technician
Reset the breaker for 30 seconds. If it returns, call for service.
3222 (E Series) Lower oven temperature sensor (RTD) open.
Call a technician
No owner fix. Call for service.
5021 (M Series) Upper oven cavity overheated during self-clean.
Call a technician
Let the oven cool fully, then reset the breaker for 30 seconds. If it returns, call for service.
3C20 (dual fuel range) High input voltage detected.
Call a technician
No owner fix. Call for service; an electrician may need to check the supply.
2C21 / 6020 / 6D10 Internal communication faults: power control module network fault on the right oven (2C21), user interface network fault (6020), or touchpad communication fault (6D10 on M Series).
Call a technician
Reset the breaker for 30 seconds and retest. If it returns, call for service.
E05 / F5 / E122 / E124 (convection steam oven) Control-detected fault on Wolf convection steam ovens. Wolf does not publish a separate meaning for these codes.
Call a technician
Reset the breaker for 30 seconds and retest. If the code returns, call for service.
F2 / F3 / F4 (older Wolf ovens) Commonly reported by repair references as: F2 oven temperature too high, F3 temperature sensor circuit open, F4 temperature sensor reading out of range.
Call a technician
Turn the oven off at the breaker. Do not keep using an oven that shows F2. Call for service.
F7 / F8 / F9 (older Wolf ovens) Commonly reported by repair references as: F7 door switch fault, F8 cooling fan fault, F9 door lock fault (often after self-clean).
Call a technician
Let the oven cool fully after self-clean, then reset the breaker. If the code returns, call for service.

What we actually find on Wolf ovens in the Denver area

The codes above come from Wolf’s own documentation. This section shows what our technicians found once they opened the machine. Since 2024 we have handled 6 Wolf oven service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The oven repairs we do most often (all brands)

Our notes on Wolf ovens are too thin to rank by brand alone, so here is what we found across all 645 oven calls in our records:

  1. Control board: 54 calls
  2. Igniter: 45 calls
  3. Bake or broil element: 26 calls
  4. Surface element or burner switch: 20 calls
  5. Wiring: 16 calls
  6. Convection fan: 15 calls
  7. Temperature sensor: 13 calls

Oven repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2024–2026. Customer details removed.

Video: Wolf oven troubleshooting

Video by Pappabob

What we see on Denver calls

  • Across all 645 oven calls in our records (all brands), the repairs we do most often: control board (54 calls), igniter (45) and bake or broil element (26).

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. Write down the exact code and your oven's series (L, E, M, legacy dual fuel, steam) from the rating plate.
  2. Turn off the oven at the circuit breaker for 30 seconds, then back on and retest.
  3. For door-lock codes, let the oven cool completely and avoid slamming the door.
  4. For probe codes, make sure the probe is fully in the food and the socket is dry.
  5. Keep the control panel dry and make sure nothing is resting on the buttons.
  6. On dual fuel ranges, turn off the gas supply before moving the range; never work on gas parts yourself.

When to call a technician

  • Any code returns after a breaker reset.
  • The oven overheats, F2 or an over-temperature code appears, or you smell burning.
  • The door stays locked after the oven has fully cooled.
  • Element, relay, sensor, fan or communication codes appear.
  • High or low voltage codes appear more than once.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

How do I reset a Wolf oven error code?

Turn the oven's circuit breaker off for about 30 seconds, then back on and test the oven. If the same code comes back, the cause is still there and the oven needs service.

What does F1 mean on a Wolf oven?

On L Series wall ovens, F1 means the door lock or unlock switches were not detected within 60 seconds. Slamming the door during heating can cause it; if it returns after a reset, the lock needs service.

What does COOL FAN mean on a Wolf range?

It means the cooling fan failed or the switch that monitors it reported a failure. The fan protects the controls and cabinetry, so stop using the oven if the code returns after a reset.

Why does my Wolf oven show a four-digit code like 5021?

Newer M Series, E Series and dual fuel models use four-character fault codes. Note the code, reset the breaker, and call for service if it returns.

Sources: subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com, subzero-wolf.com. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229
Call Now Book Online