Electrolux Washer Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

Five Electrolux washer codes come up far more than the rest: E11 (fill too slow), E21 or EF1 (drain too slow or pump clogged), E41 or E42 (door open or not locking), SU dS or EF2 (suds overload) and HO SE (hot and cold hoses reversed). Open the valves, empty the drain pump filter, shut the door firmly, cut back on HE detergent or swap the hoses. Codes in the E5x, E6x, E7x and E9x ranges cover the motor, heater, sensors and boards and usually need a technician.

Electrolux front-loaders show an E-code and usually beep. The same Electrolux platform sits inside Frigidaire and Kenmore 417-series front-loaders, so the code families line up across all three. Our list starts from Electrolux’s support articles and adds Sears parts documentation and repair references; meanings can still differ by model, and the tech sheet behind the top or front panel is the final word. Unplug the washer and close both water valves before you inspect anything.

Electrolux washer codes by system

Water in

Code Electrolux washer meaning Practical step
E11, E10 Water level not reached in time (E11); reported as an inlet fault on some models (E10). Open both faucets, straighten hoses, and with power and water off, clean the hose screens. Make sure the drain hose is not so deep in the standpipe that it siphons.
HO SE Hot and cold hoses connected backwards; the display alternates HO and SE. Cancel, close the valves, swap the hoses, reopen, run a cycle.
EF4, EC1 Commonly reported: no water sensed with the valves open (EF4), or water flowing when it should not (EC1). EF4: faucets and hoses. EC1 or water that will not stop: close the valves and call.
E35 Pressure sensor reads overfill.
Technician
Water off. Filling while unplugged means a stuck inlet valve; otherwise the sensor.

Water out, suds and leaks

Code Electrolux washer meaning Practical step
E21, E20, E22 Pump-out takes too long (E21); E20 and E22 are reported as related drain faults. Unplug, set out towels and a shallow pan, and empty the pump filter behind the lower front panel. Check the hose and standpipe.
EF1 Pump or drain hose clogged. Clear the filter and hose. A pump that hums but will not move water needs replacing.
E23, E24, E25 Commonly reported: drain pump control circuit on the main board.
Technician
Unplug five minutes and run again; a repeat means diagnosis.
SU dS, EF2 Suds overload; the washer pauses and adds rinses. Let it finish, measure HE detergent, run an empty hot cycle. Front Range hard water does not call for extra soap.
E13 Water leaking from the tub, or air escaping the pressure sensor hose.
Technician
Look under and behind the machine; if wet, close the valves.
E31, E32, E38 Pressure sensor not communicating or out of calibration (E31, E32), or its air trap is clogged (E38).
Technician
Unplug five minutes and run again; a repeat means diagnosis.

Door and lock

Code Electrolux washer meaning Practical step
E41, E40 The door reads open. Push until it clicks; pull any sock or debris out of the seal and inspect the striker.
E42 Lock not recognized as locked. Close fully, listen for the lock click. If it keeps happening, the lock assembly is replaced.
E43, E44, E45, E47, E48, E4A Lock circuit faults; E47 means it opened during spin. On some models E44 and E45 are reported as board faults.
Technician
Unplug five minutes and run again; a repeat means diagnosis.

Motor and balance

Code Electrolux washer meaning Practical step
E50, E52, E54, E59 Motor fault (E50), speed signal bad or missing (E52, E59), over speed (E54).
Technician
Unplug five minutes and try a smaller load.
E53, E55, E56, E57, E58 Low voltage to the motor board (E53), under speed or overheating (E55), high motor current (E56 to E58). A worn bearing or binding drum can cause them.
Technician
Unplugged, the drum should turn freely by hand.
E5A to E5F Motor board overheated (E5A to E5C) or lost the main board (E5D to E5F).
Technician
Let it rest 30 minutes and restart.
EF5 Commonly reported: load out of balance, spin skipped or limited. Spread the load, pair a heavy item with a couple of similar ones, level the washer, rerun Spin.

Heating, sensors, power and controls

Code Electrolux washer meaning Practical step
E60, E61, E62, E68 Internal heater models: heating fault (E60), no heat (E61), overheating (E62), heater failure (E68).
Technician
Wash on cold meanwhile.
E71, E75 Heater temperature sensor (E71) or water temperature sensor circuit (E75).
Technician
Unplug five minutes and run again; a repeat means diagnosis.
E67, EA1 to EB3 Wrong voltage at the board (E67); supply frequency or voltage out of range, or a sensing fault (EA, EB codes).
Technician
Plug straight into a grounded outlet, never an extension cord; an electrician checks the outlet before parts are ordered.
E91 to E9F Main control, interface and motor control are not communicating.
Technician
Unplug five minutes and run again; a repeat means diagnosis.
EF6, EF8 Control reset (EF6) or a stuck button (EF8). EF6: unplug five minutes. EF8: press keys firmly.
LOC Control lock is on; keys will not respond. Hold the lock key or key pair for a few seconds.

What we actually find on Electrolux washers in the Denver area

The codes above come from Electrolux’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 9 Electrolux washer service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

Code Our calls What we found
E11 1 Water inlet valve.

The washer repairs we do most often (all brands)

Our notes on Electrolux washers are too thin to rank by brand alone, so here is what we found across all 1238 washer calls in our records:

  1. Control or display board: 108 calls
  2. Drain pump: 74 calls
  3. Shock absorbers or suspension: 57 calls
  4. Water inlet valve: 41 calls
  5. Door or lid lock: 28 calls
  6. Door boot seal: 27 calls
  7. Drive belt or coupler: 23 calls

Recent Electrolux washer calls

  • Thornton (80229), February 2026: Electrolux washer leaking. Repair: door boot seal replaced (5304510094).
  • Boulder (80304), November 2025: Electrolux washer not draining. Diagnosis: drain pump.
  • Evergreen (80439), March 2025: Electrolux washer showing E11. Repair: water inlet valve replaced.

Washer repairs from $240. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Electrolux washer control or display board repair

Video by RepairClinic.com

What we see on Denver calls

  • The video shows a control or display board repair. It is the most common washer repair on our calls (all brands).
  • Across all 1238 washer calls in our records (all brands), the repairs we do most often: control or display board (108 calls), drain pump (74) and shock absorbers or suspension (57).
  • Recent call: Thornton (80229), February 2026: Electrolux washer leaking. Repair: door boot seal replaced (5304510094).

Don’t want to do it yourself? Call 720-230-1229.

Electrolux washer: what to check yourself

  1. Unplug and close both supply valves.
  2. For fill codes, reopen the valves and clean the inlet screens.
  3. For drain codes, empty the pump filter behind the lower panel.
  4. For door codes, clean the gasket and latch and close firmly.
  5. Measure HE detergent, then try one cycle.

Get a technician if

  • An E5x, E6x, E7x or E9x code returns after the reset.
  • It will not drain even with a clean pump filter.
  • E13 or E35 appears, or water keeps entering while it is off.
  • The door will not lock or unlock, or the drum grinds, binds or smells hot.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Electrolux washer code FAQ

How do I reset an Electrolux washer?

Unplug it for about five minutes, plug it back in and start a cycle.

What does E21 mean?

The washer is draining too slowly. Clean the pump filter behind the lower front panel and check the drain hose.

What does HO SE mean?

The hot and cold hoses are connected backwards. Swap them and run again.

Do Electrolux and Frigidaire washers share codes?

Largely yes, because Frigidaire front-loaders use the same Electrolux platform.

Sources: owner.electrolux.com, owner.electrolux.com, owner.electrolux.com, owner.electrolux.com, owner.electrolux.com, owner.electrolux.com, owner.electrolux.com, owner.electrolux.com, owner.electrolux.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, appliancepartspros.com. Codes and meanings can vary by model; check your owner’s manual.

720-230-1229
720-230-1229
Call Now Book Online