An Electrolux refrigerator display shows two kinds of messages. Alarms such as H or HI (too warm for over an hour), PF (power failure), Door Ajar and DI SP (ice jam) usually clear on their own once the cause is gone. Fault codes such as SY EF (evaporator fan), SY CE or SY CF (boards not communicating), OP or SH (sensor open or shorted) and dF (defrost) point to a part, and if they survive a power reset a technician should look at them.
Codes appear in the temperature readout, often with letters that look like numbers: “SY” can show as “5Y”, and Sabbath shows as “Sb”. US Electrolux refrigerators use the same control family as Frigidaire, which is why repair references list matching codes for both. We built this list from Electrolux’s alarm guide first, then parts documentation for the service codes. While you troubleshoot, put a thermometer in the fresh-food and freezer sections so you know whether food is at risk.
Electrolux refrigerator codes
Temperature, power and door alarms
| On the display | Why it appears | Your move |
|---|---|---|
H, HI |
A compartment has been warm for longer than an hour. The temperature blinks and a tone plays. | Close and check every door seal, press Clear Alerts if you have it, and check food. Not recovering within a few hours means service. |
PF |
Power failed or surged, which can also set off the high-temp alarm. | Press Clear Alerts, or unplug for 30 seconds. Check anything that may have warmed. |
PO |
Commonly reported on some models as a power outage indicator. | Acknowledge it and take food temperatures. |
| Door Ajar | A door has been open longer than 5 minutes. | Push bins and shelves fully in, and make sure the fridge tilts slightly back so doors swing closed. |
| Beeping, display on, no code | A brief power interruption or an unlisted error. | Unplug for 2 to 3 minutes and plug back in. |
Ice and dispenser
| On the display | Why it appears | Your move |
|---|---|---|
DI SP, DISP |
Ice has jammed in the dispenser chute. | Clear the chute. If cubes are fused, pull the bin, let it thaw, dry it and reinstall. Dispensing restarts with fresh ice. |
Fan, sensor, defrost and board faults
| On the display | Why it appears | Your move |
|---|---|---|
SY EF, 5Y EF, EF |
The evaporator fan circuit failed, so cold air may not be leaving the freezer coil area. Technician |
With the freezer door shut, listen for the fan. Make sure ice is not holding the blade. One reset; a repeat means the fan motor, wiring or board. |
SY CE, SY CF, 5Y CE, Er CE |
The main board and the display board have stopped talking. Technician |
Five minutes unplugged. If it returns, the harness and both boards get tested. |
OP |
Open temperature sensor. On the freezer readout it is the freezer sensor; on the fresh-food readout, the fresh-food sensor. Technician |
Five-minute unplug; a repeat means the sensor or wiring. |
SH |
Shorted temperature sensor in whichever compartment shows it. Technician |
Same as OP. |
dF, DF |
The control cannot detect the defrost circuit. Technician |
A thick frost layer on the freezer back wall confirms it. Heater, thermostat or control needs testing. |
Modes that look like faults
| On the display | Why it appears | Your move |
|---|---|---|
Sb, SB SB |
Sabbath mode limits lights, alarms and the dispenser. | On many models, hold minus and Temp F-C about 5 seconds. |
77 77 |
Demo (showroom) mode; the unit may not be cooling at all. | Unplug for five minutes to leave demo mode. |
What we actually find on Electrolux refrigerators in the Denver area
The codes above come from Electrolux’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 7 Electrolux refrigerator service calls across the Denver metro and Boulder County. Every number here comes from our own job records.
The refrigerator repairs we do most often (all brands)
Our notes on Electrolux refrigerators are too thin to rank by brand alone, so here is what we found across all 1685 refrigerator calls in our records:
- Compressor or sealed system: 167 calls
- Evaporator or condenser fan: 121 calls
- Control or inverter board: 120 calls
- Ice maker: 109 calls
- Defrost system: 66 calls
- Thermistor or sensor: 37 calls
- Water inlet valve: 32 calls
Recent Electrolux refrigerator calls
- Longmont (80504), July 2026: Electrolux refrigerator not cooling. Repair: control or inverter board replaced (5304510307).
- Wheat Ridge (80033), March 2026: Electrolux refrigerator ice maker not working. Repair: ice maker replaced.
Refrigerator repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.
Source: The Appliance Team service records, 2023–2026. Customer details removed.
Video: Electrolux refrigerator error codes
Video by Live Free
What we see on Denver calls
- An error code points to the system that reported the fault, not always to the part that failed.
- Across all 1685 refrigerator calls in our records (all brands), the repairs we do most often: compressor or sealed system (167 calls), evaporator or condenser fan (121) and control or inverter board (120).
- Recent call: Longmont (80504), July 2026: Electrolux refrigerator not cooling. Repair: control or inverter board replaced (5304510307).
Don’t want to do it yourself? Call 720-230-1229.
What to check at home
- Wipe door gaskets clean and close every door firmly.
- Clear the display with Clear Alerts, or unplug for 30 seconds.
- Move food away from the vents in both compartments.
- Unplug and vacuum the condenser area behind the bottom grille.
- Track temperatures with thermometers: target about 37 °F and 0 °F.
Time for a technician when
- SY EF, SY CE, OP, SH or dF returns after the reset.
- The fresh-food section stays above 40 °F for hours with the doors shut.
- Frost keeps building on the back wall of the freezer.
- The compressor runs without cooling, or keeps clicking on and off.
Keeping food cold while a fan or defrost code waits for repair
SY EF and dF have the same end result: cold air stops reaching the fresh-food side, even though the freezer may still feel cold. If the evaporator coil is buried in frost, a manual defrost can buy a few days of normal cooling until the part is replaced.
- Move food into coolers with ice, or to a second fridge.
- Unplug the refrigerator and leave both doors open. Lay towels on the floor and under the crisper drawers.
- Give it 24 hours, or about 8 if you speed things up with a fan blowing into the freezer. Do not chip at ice with sharp tools; it is easy to puncture tubing.
- Wipe up the meltwater, plug it back in, and let it run 4 to 6 hours empty before restocking.
- If the code or warm temperatures return within a few days, the fan motor, defrost heater or control still needs repair; the manual defrost only clears the symptom.
How to prevent this
Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:
Electrolux refrigerator code FAQ
How do I reset an Electrolux refrigerator?
Press Clear Alerts for alarms. For fault codes, unplug it for about five minutes and plug it back in.
What does SY EF mean?
The control lost the evaporator fan circuit. Without the fan, the fresh-food section warms even when the freezer is cold.
Why does my Electrolux show 77 77?
It is in demo mode. Unplug it for five minutes to return to normal cooling.
Sources: owner.electrolux.com, searspartsdirect.com, owner.frigidaire.com, appliancepartspros.com. Codes and meanings can vary by model; check your owner’s manual.