Electrolux Dryer Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

Four Electrolux dryer codes cover most calls: EF1 says the vent is restricted, E42 says the door is open or not sensed, E4 says the humidity sensor quit, and H2/B2 or H4/B4 say the incoming power or its wiring is wrong. Start with the lint filter, the vent run and a firm door close. Codes in the E5x, E6x, E7x and E9x ranges cover the motor, heat, thermistors and controls and usually mean a technician.

Electrolux dryers display short letter-and-number codes. Frigidaire dryers come from the same Electrolux platform, so many codes overlap, but Electrolux publishes its own code guide, which we used first. Parts-catalog listings fill the gaps and are marked “some models”. Full-size vented dryers and compact heat-pump condensing dryers use different code sets, so the compact ones have their own table at the end. Before you touch anything: unplug the dryer, and on gas units close the gas shutoff.

Electrolux dryer codes, grouped by system

Airflow, door and drying time

Code Electrolux meaning Our recommendation
EF1 Air cannot move freely through the dryer and duct. Pull the lint filter and vacuum the slot under it, then disconnect the duct and clear it to the outside hood. Restricted venting is the top cause of dryer fires.
EF3 The cycle hit its maximum time, typically from weak airflow or a coated moisture sensor. Clean filter, duct and sensor bars; dry smaller loads.
E42 Door reads open, or the control has lost track of its position. Check for a sleeve caught in the seal. If the door is shut and the code stays, the switch or board gets tested.
E65, E66, E8C Overheat protection: high-limit thermostat tripping repeatedly (E65, E8C on some models) or the thermal limiter has opened (E66). Nearly always a vent problem. Clear the entire run; if it is clean and the code returns, the cause of overheating and the tripped part both need attention.

Moisture and temperature sensing

Code Electrolux meaning Our recommendation
E4 Humidity sensor failure. The current load finishes and timed cycles still work. Wipe the two metal bars inside the drum with rubbing alcohol and use Timed Dry meanwhile.
E31, E32 Moisture signal too high (E31) or too low (E32), often from residue or a coin touching the bars. Empty pockets, clean the bars. A repeat points at the sensor harness or control.
E71, E72, E73 Outlet thermistor (E71, E72) or inlet thermistor (E73).
Technician
The thermistor and its wiring get a resistance test.
E24, E25 Some models: thermistor open or shorted.
Technician
Same resistance test.

Heat

Code Electrolux meaning Our recommendation
E61, E63, E64 Electric heat: heater relay (E61), element shorted to the cabinet (E63), element circuit open (E64). The drum turns but stays cold.
Technician
Reset both breakers once. Do not keep running a dryer with a shorted element.
E67 The heating sensor on the control board has failed.
Technician
Unplug for five minutes and restart; a repeat needs a service visit.
E4A, E5B Some models: dry time too long, usually from a heat problem (E4A), or no heat at all (E5B).
Technician
Check the breaker on electric units or that the gas valve is fully open on gas units, then clean the vent.

Drive motor

Code Electrolux meaning Our recommendation
E51, E52, E53, E54, E74 Motor relay (E51, E74), motor stalled or not starting (E52), centrifugal switch (E53), motor sensing (E54).
Technician
Take out half the load and give the motor 30 minutes to cool. Unplugged, the drum should turn by hand.

Power, controls and buttons

Code Electrolux meaning Our recommendation
H2 / B2 Supply voltage is not what the control expects.
Technician
Reset both breakers. If it repeats, Electrolux suggests calling the power company; an electrician can test the outlet.
H4 / B4 Wiring error, usually at the cord or terminal block from installation.
Technician
Have the installer or an electrician recheck the cord. Never open the terminal cover with the dryer plugged in.
EA1 to EA5 Frequency out of range (EA1), voltage high (EA2) or low (EA3), terminal block wiring (EA4), control defect (EA5).
Technician
Electrician checks power first; if it is correct, the board is next.
E91, E92, E93, E94, E97 Interface-to-board communication (E91), wrong part installed (E92), configuration errors (E93, E94), software mismatch (E97).
Technician
After a recent repair, confirm the part number fits your model.
E10, E11, E12, EAF Some models: board communication fault or board failure.
Technician
Unplug for five minutes and restart; a repeat needs a service visit.
EF8, E68 A panel button is stuck (E68 on some models). Press each button firmly; one that will not release means a new interface.
AD, Mute Auto Dry indicator and silenced chimes. Not faults. Nothing to fix.

Compact heat-pump condensing dryers

Code Electrolux meaning Our recommendation
Ex21, Ex22, Ex31, Ex32, Ex45 Condensate pump (Ex21, Ex22), humidity sensor (Ex31, Ex32) or door open (Ex45). The x is a variable digit. Empty the water tank, straighten the drain hose, close the door firmly.
Ex51 to Ex54, E57 to E5H Motor or inverter faults, including overload heating (Ex52) and a jammed drum (Ex54).
Technician
Lighten the load and let it cool.
Ex62, Ex63, Ex64, Ex71 Heat pump compressor (Ex62 to Ex64) or temperature sensor (Ex71).
Technician
Compressor work is for a technician only.
Ex83 to Ex9E, ExH1 to ExHF, EH1 to EH3 Main board, interface or power supply.
Technician
Unplug for five minutes and restart; a repeat needs a service visit. Have outlet voltage checked too.

What we actually find on Electrolux dryers in the Denver area

The codes above come from Electrolux’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 14 Electrolux dryer service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The dryer repairs we do most often (all brands)

Our notes on Electrolux dryers are too thin to rank by brand alone, so here is what we found across all 983 dryer calls in our records:

  1. Heating element: 88 calls
  2. Drive belt: 35 calls
  3. Idler pulley or drum rollers: 33 calls
  4. Clogged vent or lint: 29 calls
  5. Thermal fuse or thermostat: 27 calls
  6. Control board: 26 calls
  7. Thermistor or sensor: 20 calls

Recent Electrolux dryer calls

  • Superior (80027), September 2026: Electrolux dryer not starting. Repair: idler pulley or drum rollers replaced.
  • Lyons (80540), August 2026: Electrolux dryer not heating. Repair: heating element replaced (5304535760).

Electrolux dryer repairs from $330. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Electrolux dryer heating element repair

Video by RepairClinic.com

What we see on Denver calls

  • The video shows a heating element repair. It is the most common dryer repair on our calls (all brands).
  • Across all 983 dryer calls in our records (all brands), the repairs we do most often: heating element (88 calls), drive belt (35) and idler pulley or drum rollers (33).
  • Recent call: Superior (80027), September 2026: Electrolux dryer not starting. Repair: idler pulley or drum rollers replaced.

Don’t want to do it yourself? Call 720-230-1229.

Our checklist for Electrolux dryer codes

  1. Unplug the dryer; on gas models close the shutoff and leave the burner alone.
  2. Wash the lint filter if dryer sheets left a waxy film.
  3. Replace any foil or vinyl duct with rigid or semi-rigid metal and clear it to the outside.
  4. Clean the moisture bars inside the drum.
  5. Electric models: flip both breaker handles off and on, then try one cycle.

Get a technician involved if

  • Motor, heat, thermistor or board codes come back after the reset.
  • Clothes come out cold even though the vent is clear.
  • H2/B2, H4/B4 or any EA code shows.
  • You smell gas or scorching, or find singed fabric.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Electrolux dryer code FAQ

What does EF1 mean on an Electrolux dryer?

The dryer detected restricted airflow. Clean the lint filter and the full vent duct; it is both a performance and a fire-safety warning.

How do I reset an Electrolux dryer?

Unplug it or switch off its breakers for about five minutes, restore power and start a new cycle.

Can I still use my Electrolux dryer with E4?

Yes, on timed cycles. Sensor-based auto cycles will not work properly until the humidity sensor issue is fixed.

Why does my dryer show H4 or B4?

It points to wiring at the power cord or terminal block, usually from installation. An installer or electrician should check it.

Sources: owner.electrolux.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, appliancepartspros.com. Codes and meanings can vary by model; check your owner’s manual.

720-230-1229
720-230-1229
Call Now Book Online