GE Oven Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

GE oven F codes point to a failed part: F0, F1, F6 and F7 usually mean a keypad problem; F3 and F4 an oven temperature sensor; F5, F8 and FF the electronic control; F2 or F20 an oven that ran too hot; and F9 or FC the door lock circuit. Turning the breaker off for a minute or two may clear a code, but if it returns, the oven needs a technician. Messages like LOC, ERR and OFF are not faults.

GE ranges and wall ovens show an F code when the control detects a fault. GE recommends keeping the oven off at the breaker until it is serviced. Codes can vary by model, so check your owner's manual if you see something not listed here. Never open the control panel or work on gas or electrical connections yourself. This list combines the manufacturer's own documentation with codes reported by established repair-parts references (such as Sears PartsDirect, PartSelect and repair technicians' guides); those are marked "commonly reported" or "on some models".

GE Oven error codes and what they mean

Code What it means What to try
F0 / F1 / F6 / F7 Keypad (touch panel) problem. Often the keypad needs replacing.
Call a technician
Turn the oven off at the breaker for a minute or two, then back on. Wipe any moisture off the panel. If the code returns, request service.
F2 / F20 Oven temperature went above a preset limit.
Call a technician
Turn the oven off at the breaker and let it cool. Do not use it until it is checked; a sensor, relay or control fault can cause runaway heat.
F3 / F4 Oven temperature sensor fault. Usually the sensor needs replacing.
Call a technician
Reset at the breaker once. If the code comes back, a technician should test and replace the sensor.
F5 / F8 / FF Electronic control fault. Usually the control needs replacing.
Call a technician
Reset at the breaker once. If the code returns, request service.
F9 / FC Fault in the door lock circuit.
Call a technician
Reset at the breaker once. If the door is locked or the code returns, do not force the door; request service.
FD The meat probe or its receptacle may be faulty. Unplug the probe and check it for damage. Try cooking without the probe. If FD stays, request service.
F350 Upper cooling fan circuit problem or a blocked fan.
Call a technician
Reset at the breaker. If it returns, a technician should check the fan and its circuit.
F96 / F97 / F7X Internal component failure.
Call a technician
Reset at the breaker once. If it returns, request service.
Bad Line Power is connected but the range is miswired.
Call a technician
Turn off the breaker and have an installer or electrician correct the wiring. Do not use the range.
LOC DOOR flashing / door will not unlock The door lock is engaged when self-clean was not selected, or the door stays locked after self-clean. Let the oven cool completely. Turn the breaker off for a minute, then back on. If the door stays locked, request service.
LOC Control lockout (child lock) is on. Not a fault. Use the lock button sequence in your owner's manual to unlock the controls.
ERR An invalid entry was made on the controls. Not a fault. Re-enter the cook settings correctly.
OFF The oven is too hot to start self-clean, or too hot to bake or broil right after self-clean. Let the oven cool fully, then try again.
⊃ (backwards C) Sabbath Mode is on. Not a fault. Turn Sabbath Mode off using the steps in your owner's manual.
F0 / F1 / F5 / F8 (repair-reference meanings) Repair references give model-dependent meanings: F0 or F1 a failed electronic control (older ranges) or a stuck function key; F5 a lost relay drive circuit; F8 a control failure on some models or a shorted meat probe on others.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
F9 (some wall ovens) On some wall ovens, commonly reported as a sail (airflow) switch error rather than the door lock.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
FF / FFF Repair references list FF as a lost door motor safety switch and FFF as a control memory (EEPROM) checksum error. Both usually need a new control.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
F21 Combination wall ovens: oven overheated while the door was locked.
Call a technician
Turn off the breaker and let the oven cool. Call a technician.
F22 Combination wall ovens: the control cannot regulate oven temperature.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
F30 / F31 Combination wall ovens: oven temperature sensor failure.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
F34 Combination wall ovens: the control cannot calibrate oven temperature.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
F40 Combination wall ovens: meat probe failure.
Call a technician
Unplug the probe and wipe the jack dry. If the code returns without the probe, call a technician.
F60 / F66 Combination wall ovens: communication error between the control board and the bridge or fan (FAD) board.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
F80 Combination wall ovens: internal control board failure.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
F90 / F91 / F92 Combination wall ovens: door lock signal fault: locked during standby or cooking (F90), unlocked during self-clean or steam clean (F91), or locked and unlocked at the same time (F92).
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
F96 / F98 (combination wall ovens) Combination wall ovens: the cooling fan is running too slowly (F96) or too fast (F98). On other GE ovens F96 is listed as an internal component failure.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.

What we actually find on GE ovens in the Denver area

The codes above come from GE’s own documentation. This section shows what our technicians found once they opened the machine. Since 2024 we have handled 91 GE oven service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

Code Our calls What we found Part we used most
F96 1 Temperature sensor. WB27T11463

The GE oven repairs we do most often

Across all 91 GE oven calls, with or without a code on the display:

  1. Bake or broil element: 5 calls
  2. Control board: 5 calls
  3. Surface element or burner switch: 3 calls
  4. Convection fan: 3 calls
  5. Igniter: 3 calls
  6. Gas valve or safety valve: 2 calls
  7. Wiring: 2 calls

Recent GE oven calls

  • Boulder (80304), February 2026: GE oven not starting. Repair: convection fan replaced.
  • Superior (80027), February 2026: GE oven door or lid problem. Diagnosis: control board (part WB27X33144).
  • Lakewood (80228), August 2025: GE oven not heating. Diagnosis: door lock.
  • Broomfield (80021), July 2025: GE oven not starting. Diagnosis: bake or broil element (part WB56X22160).

GE oven repairs from $200. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2024–2026. Customer details removed.

Video: GE oven error codes

Video by YeechBlitz

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • The GE oven repairs we do most often across the Denver metro and Boulder County: bake or broil element (5 calls), control board (5) and surface element or burner switch (3).
  • Recent call: Boulder (80304), February 2026: GE oven not starting. Repair: convection fan replaced.

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. Turn the oven off at the circuit breaker for a minute or two, then back on to see if the code clears.
  2. If the code returns, leave the breaker off until the oven is serviced. On a range you can switch it on briefly to use the cooktop.
  3. Let the oven cool fully before trying self-clean again or touching the door.
  4. Check that the controls are not locked (LOC) and that Sabbath Mode is off.
  5. Unplug the meat probe if FD appears.
  6. For gas ranges, never adjust gas connections yourself.

When to call a technician

  • Any F code comes back after a breaker reset.
  • The oven overheats (F2 or F20) or keeps heating when turned off.
  • The door stays locked after the oven has fully cooled.
  • Bad Line appears, or you smell gas or burning.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

How do I clear an F code on my GE oven?

Turn the oven off at the circuit breaker for a minute or two, then turn it back on. If the code clears and stays gone, the oven is safe to use; if it returns, leave the breaker off and request service.

What does F3 mean on a GE oven?

F3 points to the oven temperature sensor. Usually the sensor or its connection has failed and needs to be replaced.

What does F9 mean on a GE oven?

F9 means GE detected a fault in the door lock circuit. The door lock motor, switch or wiring needs to be checked by a technician.

My GE oven shows F7. Is the oven broken?

F7 usually means the keypad (touch panel) has a fault, not the heating system. Reset at the breaker; if it returns, the keypad typically needs replacing.

Sources: products.geappliances.com, ifixit.com, searspartsdirect.com, partselect.com, needapplianceparts.com. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229
Call Now Book Online