KitchenAid Dishwasher Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

Most KitchenAid dishwasher codes we get called about are drain or water problems: F9E1 means the tub did not empty in time, H2O means no water came in, and F8E4 means water reached the drip tray under the tub. Those three often start with a clogged filter, a kinked hose or a closed valve. Codes for the heater, wash motor, diverter, sensors or the control board need a technician.

KitchenAid dishwashers come off the same Whirlpool production lines, so the F#E# logic is shared. A few codes changed meaning between older and current control boards; where that happens we give both. No display? Watch the Clean light: count the first burst of blinks (the F number), wait for the pause, then count the second burst (the E number). Nine blinks, pause, one blink is F9E1. Unplug the unit before touching anything inside, and close the supply valve if you see water on the floor. Meanings come from KitchenAid’s own help pages plus parts and repair references; anything marked “older” or “some models” is from the latter.

KitchenAid dishwasher codes by problem area

Draining

Code (flashes) Meaning on a KitchenAid Try this first
F9E1 (9, 1) Current boards: draining took too long. Some older boards: the diverter disc position could not be read. Pull and rinse the filter cylinder. Straighten the drain hose, run the disposer, and on a new install make sure the disposer knockout plug is out. Clean the air gap cap.
F8E1, F8E2 Older boards: slow drain (E1) or drain pump electrical fault (E2).
Technician
Filter and hose first. If the path is clear, the pump or its wiring is next.
F8E3 (8, 3) Older boards: drain pump will not switch off.
Technician
Five-minute power reset. Repeat means service.
F3E3 Can indicate dirty water siphoning back in from the drain line, as well as a sensor fault. The drain hose needs a high loop under the counter or an air gap.

Water supply, fill and leaks

Code (flashes) Meaning on a KitchenAid Try this first
H2O The machine did not sense any incoming water. Open the valve under the sink fully and look for a pinched supply line.
F6E2 Inlet valve not working.
Technician
Confirm water is on; a repeat means the valve or its wiring.
F6E1 (6, 1) Older boards: no fill. (On current boards this is a control code, see below.) Check the water and make sure nothing props up the float at the front of the tub.
F6E3 Suds, air in the pump or too little water. Wipe out the suds and run an empty rinse. Use dishwasher detergent only.
F6E4 The overfill float switch reads open. Clear anything sitting on the float and check the dishwasher is level.
F6E7 (6, 7) Flow meter unplugged or damaged, on models that have one.
Technician
Five-minute power reset, then service if it returns.
F6E8 (6, 8) Softener models: regeneration valve problem.
Technician
Five-minute power reset, then service.
F8E4 (8, 4) Water collected in the base pan, which trips the leak sensor.
Technician
Close the supply valve. Check the supply fitting and look for suds from the wrong soap. A leak inside needs a tech.
FAE5 / F10E5 (10, 5) Possible leak at the diverter.
Technician
Look under the unit for water and snug the connections. Press Cancel twice and restart.

Heating, drying and dispensing

Code (flashes) Meaning on a KitchenAid Try this first
F6E6 Incoming water is too cold. Run the sink hot before starting and set the water heater near 120 °F.
F4E2, F4E3 Current boards: heating system fault.
Technician
Five-minute reset. Wet, cool dishes after a cycle confirm it.
F7E1 Older boards: heating element not working.
Technician
Heater and wiring test.
F7E2 Current boards: wash motor fault. Older boards: element stuck on.
Technician
30-second reset, then service if it repeats.
FAE1, FAE2, FAE3 (10, 1-3) Detergent dispenser (E1), vent wax motor (E2) or drying fan (E3).
Technician
Make sure tall pans are not blocking the dispenser lid.

Wash pump, diverter and spray arms

Code (flashes) Meaning on a KitchenAid Try this first
F4E4; F4E3 on some Global HE units Main board lost communication with the wash pump motor.
Technician
Power reset; repeat means service.
FAE4 / F10E4 (10, 4) Diverter valve, which routes water to the upper or lower arm.
Technician
Five-minute reset, then service.
F9E2, F9E3, F9E4 Older boards: diverter motor stuck on (E2), diverter disc missing (E3), lower arm blocked (E4).
Technician
Spin the lower spray arm by hand and remove anything that catches it.

Door, panel, sensors and control

Code (flashes) Meaning on a KitchenAid Try this first
F5E1, F5E2 Door switch fault, or the board never saw the door open between cycles. Shut the door within about 4 seconds of pressing Start. Open, close and restart. A repeat after reset means the latch.
F3E1, F3E2 Temperature thermistor or OWI (water clarity) sensor.
Technician
Power reset; service if it returns.
F2E1, F2E2 A key reads as held down (E1), or the panel cannot reach the main board (E2). Dry the panel, press each key once, reset power.
F6E1 Current boards: main control or user interface error.
Technician
30-second reset, then service.
F1E1, F1E2 Main board: stuck relay (E1) or corrupted memory (E2).
Technician
Five minutes without power. A returning code means the board.

What we actually find on KitchenAid dishwashers in the Denver area

The codes above come from KitchenAid’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 30 KitchenAid dishwasher service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

Code Our calls What we found Part we used most
F7E1 3 Most often: circulation pump or wash motor. Also seen: control board. W11414076

The dishwasher repairs we do most often (all brands)

Our notes on KitchenAid dishwashers are too thin to rank by brand alone, so here is what we found across all 702 dishwasher calls in our records:

  1. Circulation pump or wash motor: 51 calls
  2. Control board: 35 calls
  3. Drain pump: 34 calls
  4. Water inlet valve: 13 calls
  5. Clogged filter or drain: 13 calls
  6. Door latch or seal: 12 calls
  7. Heating element: 11 calls

Recent KitchenAid dishwasher calls

  • Commerce City (80022), October 2026: KitchenAid dishwasher showing F7E1. Repair: circulation pump or wash motor replaced (W11414076).
  • Longmont (80504), February 2026: KitchenAid dishwasher showing F9E1. Repair: control board replaced.

KitchenAid dishwasher repairs from $300. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: KitchenAid dishwasher control board repair

Video by RepairClinic.com

What we see on Denver calls

  • The video shows a control board repair. It is the #2 dishwasher repair on our calls (all brands).
  • Across all 702 dishwasher calls in our records (all brands), the repairs we do most often: circulation pump or wash motor (51 calls), control board (35) and drain pump (34).
  • Recent call: Commerce City (80022), October 2026: KitchenAid dishwasher showing F7E1. Repair: circulation pump or wash motor replaced (W11414076).

Don’t want to do it yourself? Call 720-230-1229.

Five-minute checks before you book

  1. Unplug the dishwasher or switch off its breaker.
  2. Twist out the filter under the lower spray arm and rinse it until no grease is left.
  3. Follow the drain hose to the sink: no kinks, disposer run, air gap clear.
  4. Check the supply valve is all the way open and the water at the sink runs hot.
  5. Restore power and run one cycle. Around Denver, hard water makes rinse aid worth adding.

Signs it is time for a technician

  • F8E4, or water on the floor.
  • Any heater, motor, diverter, sensor or board code that survives a reset.
  • The tub holds water even after the filter and hose are clean.
  • A burning smell or a scorched spot on the control panel.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

KitchenAid dishwasher code FAQ

How do I read the blinking Clean light?

Count the first group of blinks, then the second group after the pause. The first number is F, the second is E. Eight and four means F8E4.

How do I clear a KitchenAid dishwasher code?

Press Cancel, or cut power at the breaker for 30 seconds (five minutes for board codes). If the cause is still there, the code will come back.

Do KitchenAid and Whirlpool dishwashers share codes?

Yes, Whirlpool builds both, though the meaning can differ between older and newer control generations, as noted above.

Sources: producthelp.kitchenaid.com, producthelp.kitchenaid.com, searspartsdirect.com, producthelp.whirlpool.com, producthelp.kitchenaid.com, searspartsdirect.com, nelihome.com. Codes and meanings can vary by model; check your owner’s manual.

720-230-1229
720-230-1229
Call Now Book Online