The most common LG dishwasher codes are OE (not draining), IE (not filling), and AE or E1 (leak or overfill detected). OE and IE usually trace to a clogged filter or kinked hose, and AE is often caused by oversudsing from using hand dish soap. HE, tE, LE, and PE point to a failed heater, sensor, or motor and need a technician.
LG dishwashers stop and show a code when water, heat, or the wash motor isn't working as expected. Several codes are caused by simple things like the wrong detergent or a dirty filter. Others mean a part has failed. These codes come from LG's support guides and trusted repair-parts references, and they can vary by model. The list combines the manufacturer's own code lists with service manuals and repair-parts references. Rows marked "on some models" or "service references" come from those repair sources, so the meaning can vary by model; check your owner's manual when in doubt.
LG Dishwasher error codes and what they mean
| Code | What it means | What to try |
|---|---|---|
OE / dE (some models) / 5C |
Drain error. The tub isn't draining, usually from a clogged filter or a pinched drain hose. | Turn off power at the breaker. Remove and clean the filter in the tub bottom. Check the drain hose under the sink for kinks. To force a drain, hold Start for 3 seconds. Clean the filter every 1 to 2 weeks. |
IE |
Inlet error. Not enough water reaches the tub. | Make sure the house has water. Confirm the shutoff valve under the sink is fully open, especially after an install or move, and that the inlet hose isn't kinked. |
AE / E1 / FE |
Leak or overfill detected. Can be caused by oversudsing, too much water, the unit not being level, a misaligned door, or an actual leak. Call a technician |
Use only dishwasher detergent, never dish soap. Load large items so they don't block the door or spray water out. If water is leaking under the unit, turn off power and water and schedule repair. |
bE |
Bubble error. Too many suds, detected to prevent a leak. | Run an empty cycle with no detergent. LG also suggests setting rinse aid to its lowest level and running a Standard cycle with a small bowl of milk on the top rack to break down suds. Restore rinse aid afterward. If bE appears with no suds, call for service. |
nE |
Vario (spray direction) motor issue. The impeller isn't spinning normally, or dishes are touching it. | Rearrange dishes so nothing hangs below the lower rack or blocks the spray arms, then restart. |
HE |
Heater error. Water isn't being heated. Call a technician |
Schedule repair. The heater, its relay, or wiring needs testing. |
tE |
Temperature sensor error, from a failed sensor or loose connection. Call a technician |
Schedule repair. |
LE / LE2 |
Wash (circulation) motor error. Call a technician |
Schedule repair. Try a power reset first by switching off the breaker for a minute. |
PE |
Water level sensor error, on certain older models. Call a technician |
Schedule repair. |
F31 |
Heat Dry fan motor not running (models with Dynamic Heat Dry). Call a technician |
Schedule repair. |
F35 |
Heat Dry temperature can't be read (models with Dynamic Heat Dry). Call a technician |
Schedule repair. |
F37 |
Auto Open Door feature isn't working. | Make sure nothing in the racks blocks the door. If it persists, schedule repair. |
CL |
Control Lock is on. Not a fault. | Press and hold the button pair labeled for Control Lock (on many models, Half Load and Energy Saver) for 3 seconds. |
CE |
Wash motor or wiring error, on some models. Repair sources treat it the same as LE. Call a technician |
Turn the breaker off for a minute and back on. Check that no glass, bone, or utensil is jammed near the pump under the filter. If CE returns, schedule repair. |
PF |
Power failure. Power was interrupted during a cycle, on some models. | Press Start to resume. If there was no outage, check the breaker. If PF shows up often, have the circuit checked. |
Cd |
Cool Dry: the dishwasher is cooling and drying after the cycle. Not a fault. | Wait for it to finish. |
Cr |
Continuous run or test mode. Not a normal operating code. | Turn the dishwasher off and back on. |
EE |
Control board memory (EEPROM) error, usually seen in test mode. Call a technician |
Unplug the appliance for 5 minutes, then restart. If the code returns, write it down and call a technician. |
OC |
On some models (service references): overflow error. Call a technician |
Use only dishwasher detergent and clean the filter. Turn off power and water if water is on the floor, then schedule repair. |
LC |
Older leak code used before about 2019 on some models; newer models show AE or E1. Call a technician |
Turn off power and water and check under the unit for water. Schedule repair if it is leaking. |
E0-E5 / SE0-SE4 (steam models) |
On models with steam, service references list these as steam generator status or fault codes: E1 heater too hot, E2 water level sensor fault, E3 water level not reached, E4 heater too cool (E0/E5/SE0 are normal). Not the same as the E1 leak code above. Call a technician |
Unplug the appliance for 5 minutes, then restart. If the code returns, write it down and call a technician. |
nC |
On smart models (service references): Wi-Fi or NFC module communication failure, usually seen in test mode. Call a technician |
Unplug the appliance for 5 minutes, then restart. If the code returns, write it down and call a technician. |
St |
On models with a UV sanitize feature: sanitary cycle running. Not a fault. | Wait for it to finish. |
What we actually find on LG dishwashers in the Denver area
The codes above come from LG’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 40 LG dishwasher service calls across the Denver metro and Boulder County. Every number here comes from our own job records.
| Code | Our calls | What we found |
|---|---|---|
| HE | 2 | Most often: circulation pump or wash motor. Also seen: heating element. |
The dishwasher repairs we do most often (all brands)
Our notes on LG dishwashers are too thin to rank by brand alone, so here is what we found across all 702 dishwasher calls in our records:
- Circulation pump or wash motor: 51 calls
- Control board: 35 calls
- Drain pump: 34 calls
- Water inlet valve: 13 calls
- Clogged filter or drain: 13 calls
- Door latch or seal: 12 calls
- Heating element: 11 calls
Recent LG dishwasher calls
- Arvada (80005), August 2026: LG dishwasher showing HE. Repair: circulation pump or wash motor replaced.
- Thornton (80602), May 2026: LG dishwasher not starting. Cause: clogged filter or drain, cleared on site.
- Westminster (80031), December 2025: LG dishwasher door or lid problem. Repair: door latch or seal replaced (4775ED3003A).
- Evergreen (80439), November 2025: LG dishwasher showing AE and leaking. Repair: door latch or seal replaced.
LG dishwasher repairs from $200. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.
Source: The Appliance Team service records, 2023–2026. Customer details removed.
Video: LG dishwasher error codes
Video by LG USA Support
What we see on Denver calls
- An error code points to the system that reported the fault, not always to the part that failed.
- Across all 702 dishwasher calls in our records (all brands), the repairs we do most often: circulation pump or wash motor (51 calls), control board (35) and drain pump (34).
- Recent call: Arvada (80005), August 2026: LG dishwasher showing HE. Repair: circulation pump or wash motor replaced.
Don’t want to do it yourself? Call 720-230-1229.
What you can safely check yourself
- Turn off the dishwasher's breaker before reaching into the tub or under the sink.
- Clean the filter at the bottom of the tub every 1 to 2 weeks. Denver's hard water can add mineral scale on top of food debris.
- Use only automatic dishwasher detergent. Hand dish soap causes suds and AE or bE codes.
- Check that the water shutoff under the sink is fully open and hoses aren't kinked.
- Load so nothing blocks the spray arms or hangs below the lower rack.
- Do a power reset by switching off the breaker for about a minute.
When to call a technician
- HE, tE, LE, PE, or F31/F35 codes.
- AE or FE with water on the floor, or with no suds and no obvious cause.
- OE continues after the filter and drain hose are clear.
- The dishwasher hums but won't wash or drain.
How to prevent this
Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:
Frequently asked questions
How do I fix the AE error on my LG dishwasher?
AE means the leak sensor detected water in the base. The most common cause is oversudsing from using the wrong detergent. Turn off power, check for leaks, and if water is pooling under the unit, a technician should find the source.
Why does my LG dishwasher show OE?
OE means the dishwasher isn't draining. Clean the filter in the tub bottom and check the drain hose for kinks. If water still sits in the tub, the drain pump may need service.
How do I reset an LG dishwasher?
Switch off the dishwasher's circuit breaker for about a minute, then turn it back on. This clears many temporary codes, but a code caused by a failed part will return.
What does bE mean on an LG dishwasher?
bE means too many bubbles were detected. It's usually caused by dish soap or too much detergent. Running an empty cycle without detergent usually clears it.
Sources: lg.com, lg.com, lgparts.com, homeserve.com, mypros.plus. Codes and meanings can vary by model; check your owner's manual.