Most GE washer messages point to no water (H2O SUPPLY or blinking Wash and Rinse lights), an unbalanced load (blinking Spin light or UE), or the lid or door (Lid light, dE, door). You can usually clear these by opening the water valves, spreading out the load, or opening and closing the lid. FE (water at a critical level) and fault codes for the motor, lid lock, pressure sensor or control board need a technician.
Newer GE washers use a Consumer Help Indicator: short messages or blinking lights that tell you why a cycle stopped. Older and front-load models also store numbered fault codes that a technician reads in service mode. Messages vary by model, so check your owner's manual if what you see is not listed here. Before any hands-on check, unplug the washer and turn off the water valves. This list combines the manufacturer's own documentation with codes reported by established repair-parts references (such as Sears PartsDirect, PartSelect and repair technicians' guides); those are marked "commonly reported" or "on some models".
GE Washer error codes and what they mean
| Code | What it means | What to try |
|---|---|---|
H2O SUPPLY / IE / Wash and Rinse lights blinking |
Water is not entering the washer, or the washer cannot sense the water level. The washer locks out for 4 minutes and may run the drain pump during that time. | Make sure both water valves are fully open and the hoses are not kinked. Unplugged, check the inlet hose screens for debris. If the water is on and the message returns, the pressure sensor may be at fault. |
Spin or Spin & Rinse light blinking |
The washer detected an out-of-balance load and is correcting it. | If clothes are wetter than normal at the end, spread the load evenly in the basket and run a Drain & Spin cycle. |
UE |
Unbalanced load (on some top-load models). | Reposition the laundry evenly and make sure the washer sits level with all four feet on the floor. Wash bulky items alone. |
Lid / Lid Locked light |
Three cycles were started without opening the lid, so the washer will not start another. | Open and close the lid, then start a new cycle. If it keeps happening, the lid switch or lock may need service. |
LId / dE |
The lid is open, so the cycle stopped. | Close the lid firmly and make sure nothing is caught under it. |
door (front-load) |
The door is not fully closed, or three cycles were started without opening the door. | Open and close the door, then start again. If it persists, the door lock may need service. |
CAnCELEd |
The cycle was paused for more than 24 hours, or the washer stopped itself because of certain errors. | Wait out the 4-minute lockout, then start the cycle again. If it keeps happening, request service. |
FE |
Water has reached a critical level in the washer. Call a technician |
Turn off the water supply and power to the washer, then call for service. Do not keep running it. |
Fault 16 / 18 |
Washer is not draining. | Unplugged, check the drain hose for kinks or clogs and make sure the house drain is clear. If the pump does not run, it likely needs replacing. |
Fault 6 / 12 / 20 / 21 |
Water overflow detected. Call a technician |
Turn off the water. If the tub keeps filling with the washer unplugged, the inlet valve is stuck open. Otherwise the pressure sensor air hose or control board needs checking. |
Fault 8 |
Water level pressure sensor problem. Call a technician |
Confirm the faucets are open and the inlet screens are clean. If the washer fills normally, the air hose or control needs service. |
Fault 25 (65 on some front-loads) |
Water level dropped when the washer was not draining, often from siphoning or a leak. | Make sure the drain hose is installed correctly and not pushed too far into the standpipe. Check under the washer for leaks. |
Fault 1 / 2 / 13 / 14 / 23 / 24 (62 on front-loads) |
Lid or door lock problem, including the basket spinning with the lock open. Call a technician |
Stop using the washer. The lid or door lock, switch or wiring needs to be checked and likely replaced. |
Fault 32 (77 on front-loads) |
The lid or door will not unlock. Call a technician |
Power off for a few minutes and try again. If it stays locked, the lock assembly needs service. |
Fault 22 / 26 / 31 |
Out of balance: the washer could not balance a dry load to start (22) or the load was out of balance during final spin (26, 31). | Redistribute the load and check that all four leveling legs touch the floor. If the basket is hard to turn by hand, a technician should check for binding. |
Fault 29 |
Too many suds stopped the cycle. | Let the suds settle, then run Rinse and Spin. Use only HE detergent and measure it. |
Fault 3 |
Locked motor: the basket or motor is not turning. Call a technician |
Remove some laundry and restart. If the basket will not turn freely by hand, request service. |
Fault 15 |
Water temperature sensor (thermistor) problem. Call a technician |
Power off for a few minutes and restart. If it returns, the sensor or its wiring needs service. |
Fault 19 / 27 |
Cycle paused too long: over 24 hours (19), or lid/door open over 15 minutes with water in the tub (27). | Restart paused cycles promptly. Run Rinse, Drain and Spin to empty the tub. |
Fault 30 |
A control panel key is stuck. Call a technician |
Press each button to free it. If the code returns, the control panel or board needs service. |
Fault 37 (front-load) |
Heater failure. Call a technician |
A technician should test the heater and temperature sensor. |
Fault 33-34, 41-51 and similar (front-load) |
Drive motor or inverter board problem. Call a technician |
Let the washer sit unplugged for about 45 minutes so the inverter can cool and reset. If it returns, request service. |
E30 (some older front-load models) |
The control did not see the water level drop during drain. It can point to a drain pump, pressure sensor or overfill problem. Call a technician |
Unplugged, check the drain hose for kinks and the house drain for clogs. If it persists, request service. |
Fault 4 |
Top-load models: the control reset its software. No problem was detected. | No repair needed. Restart the cycle. |
Fault 5 / 10 |
Top-load models: mode shifter failure (the part that switches between agitate and spin). Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
Fault 9 |
Top-load models: the lid was not opened for 3 cycles in a row. | Open and close the lid, then start a new cycle. |
Fault 11 |
Top-load models: the household power supply is not 60 Hz. Call a technician |
Have an electrician check the outlet and supply. Do not use a generator or inverter that may give unstable power. |
Fault 17 |
Top-load models: the basket would not spin at the start of the wash cycle. Call a technician |
Unplug the washer and check that nothing is wedged between the basket and tub. If it repeats, call a technician. |
E22 (front-load) |
Fill timeout: no water, or water filling very slowly. | Open both water valves fully, straighten the hoses, and clean the inlet screens. If the code repeats, call a technician. |
E23 (front-load) |
Overfill or flood-protection drain: the washer detected too much water (foam switch closed while idle). Call a technician |
Turn off the water valves and unplug the washer. Call a technician; an inlet valve or level sensor is likely at fault. |
E31 (front-load) |
Drain timeout: the washer is draining too slowly. | Unplug the washer, clean the drain pump filter and check the drain hose for kinks. If it repeats, call a technician. |
E38 / E39 (front-load) |
Dispenser fault: the dispenser cannot reach its position (E38) or does not move (E39). Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
E42 / E45 / E49 (front-load) |
Drive motor current or overload fault, often from an overloaded drum or a motor problem. Call a technician |
Remove part of the load and restart. If the code returns, call a technician. |
E43 / E4A / E4B / E4C / E4E (front-load) |
Inverter (motor control) board or supply voltage fault: inverter failure (E43), low or high DC bus voltage (E4A, E4C), a power-up fault (E4B), or low voltage after start (E4E). Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
E46 / E47 / E48 (front-load) |
Drive motor or inverter overheating (E46, E47), or an open motor winding (E48). Call a technician |
Let the washer cool for 30 minutes and use smaller loads. If the code returns, call a technician. |
E4F / E53 / E57 / E58 (front-load) |
Control board software or communication fault: memory (EEPROM) fault, buffer error, checksum failure or communication failure. Sears PartsDirect lists E57 and E58 as a main control board failure. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
E52 / E54 (front-load) |
The main control lost its link with the drive motor control. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
E60 / E61 / E63 / E64 (front-load) |
Door lock problem: door lock switch fault (E60), door unlock switch fault (E61), or the door was detected open unexpectedly (E63, E64 while running). Call a technician |
Close the door firmly and make sure nothing is caught in the gasket. If the code returns, call a technician. |
E62 (front-load) |
System contact fault involving the heater, pump, pressure switch or door lock circuits; often a loose connection. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
E65 (front-load) |
Water level (pressure) sensor failure. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
E66 / E67 (front-load) |
Water temperature sensor open (E66) or shorted (E67). Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
E70 / E71 (front-load) |
A control panel key is stuck (E70) or the control cannot read the keys (E71). Call a technician |
Press each button firmly to free any that are stuck, then unplug for 5 minutes. If it returns, call a technician. |
IE / 7E / E / OE (WSL models) |
Older GE WSL top-loads: water level sensor error (IE), water supply error (7E), drain pump error (E), or water overflow (OE). On newer GE washers, IE means water is not entering. | Check that both water valves are open and the drain hose is clear. For OE, turn off the water and call a technician. |
353 / 18 (UltraFast Combo) |
GE Profile UltraFast Combo washer/dryer: 353 means the lint filter is clogged (often with fabric softener residue); 18 means the drain pump filter needs cleaning. | Unplug the unit. Rinse and scrub the lint filter, or clean the pump filter, then run a cycle. |
What we actually find on GE washers in the Denver area
The codes above come from GE’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 150 GE washer service calls across the Denver metro and Boulder County. Every number here comes from our own job records.
| Code | Our calls | What we found | Part we used most |
|---|---|---|---|
| 26 | 3 | Most often: shock absorbers or suspension. Also seen: control or display board. | WH22X38837 |
| 19 | 1 | Shock absorbers or suspension. | WH22X38837 |
| E45 | 1 | Drive belt or coupler. | WH08X10050 |
The GE washer repairs we do most often
Across all 150 GE washer calls, with or without a code on the display:
- Control or display board: 23 calls
- Door or lid lock: 7 calls
- Drive belt or coupler: 6 calls
- Water inlet valve: 6 calls
- Drain pump: 5 calls
- Shock absorbers or suspension: 3 calls
- Door boot seal: 3 calls
Recent GE washer calls
- Denver (80204), October 2026: GE washer showing E45 and not spinning. Diagnosis: drive belt or coupler (part WH08X10050).
- Broomfield (80023), September 2026: GE washer not draining. Repair: control or display board replaced (WH22X37840).
- Arvada (80007), September 2026: GE washer showing 26 and stopping mid-cycle. Repair: shock absorbers or suspension replaced (WH22X38837).
- Broomfield (80020), August 2026: GE washer leaking. Repair: water inlet valve replaced (WH13X26637).
GE washer repairs from $290. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.
Source: The Appliance Team service records, 2023–2026. Customer details removed.
Video: GE washer error codes
Video by l10ydchristmas
What we see on Denver calls
- An error code points to the system that reported the fault, not always to the part that failed.
- The GE washer repairs we do most often across the Denver metro and Boulder County: control or display board (23 calls), door or lid lock (7) and drive belt or coupler (6).
- Recent call: Broomfield (80023), September 2026: GE washer not draining. Repair: control or display board replaced (WH22X37840).
Don’t want to do it yourself? Call 720-230-1229.
What you can safely check yourself
- Unplug the washer and turn off both water valves before any hands-on check.
- Make sure both valves are fully open and the fill hoses are not kinked.
- Check the drain hose for kinks and make sure it is not pushed too far into the standpipe.
- Spread out the load, wash bulky items alone, and check that the washer sits level.
- Use only HE detergent and measure it to avoid suds problems.
- Open and close the lid or door between cycles.
- For other messages, power off for a few minutes, then restart the cycle once.
When to call a technician
- FE appears, or water keeps filling with the washer off.
- The basket spins with the lid open, or the lid or door will not lock or unlock.
- The washer will not drain even though the hose and house drain are clear.
- A motor, heater, sensor or control code keeps coming back after a reset.
- You hear grinding or banging, or smell burning.
How to prevent this
Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:
Frequently asked questions
How do I reset a GE washer?
Unplug the washer or switch off its breaker for a minute or two, then restore power and start a new cycle. After H2O SUPPLY or CAnCELEd, the washer locks out for 4 minutes, and unplugging restarts that timer.
Why is the Spin light blinking on my GE washer?
The washer detected an unbalanced load and is trying to correct it. If the clothes come out wetter than usual, spread them out and run a Drain & Spin cycle.
Why does my GE washer say H2O SUPPLY when the water is on?
Check that both valves are fully open and the inlet hose screens are not clogged. If water still does not enter, or it fills normally and the message returns, the water valve or pressure sensor likely needs service.
How do I see the stored fault codes on a GE washer?
GE washers store numbered fault codes that are read in a service mode, and the steps differ by model. A technician uses these codes along with the model's tech sheet to find the failed part.
Sources: products.geappliances.com, products.geappliances.com, products.geappliances.com, searspartsdirect.com, searspartsdirect.com, appliancepartspros.com, ifixit.com, searspartsdirect.com, removeandreplace.com, needapplianceparts.com, partselect.com, products.geappliances.com, forum.upfix.com. Codes and meanings can vary by model; check your owner's manual.