KitchenAid Refrigerator Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

Most things that light up on a KitchenAid refrigerator are reminders, not breakdowns: PO after a blackout, Temperature Alarm after a warm spell, Door Alarm, Cooling Off, and the filter lights. A blinking F, sometimes followed by a code like F3 E1 or F8 EC, is different: the control has logged a fault. KitchenAid’s instruction for every F code is the same, a one-minute power cycle, and a technician visit if the F comes back.

Whirlpool manufactures KitchenAid refrigerators, and the control logic is close to Whirlpool’s. What KitchenAid does not do is publish what each F#E# means, so any meaning we give for those is drawn from technician reports and tech-sheet summaries and is labelled that way. Built-in KitchenAid models (KBFN and similar) and French door models (KRMF, KRFC and similar) also have their own ice maker and service-mode readouts, covered further down. Switch off the breaker before reaching behind panels or near the coils.

KitchenAid refrigerator displays and codes

Alerts and reminders

Display Meaning Homeowner step
PO A blackout lasted long enough for the freezer to reach roughly 18 °F (-8 °C). Acknowledge it (on many models, Measured Fill under Confirm). Sort through frozen food and discard anything soft.
Temperature Alarm Fresh food over 48 °F (9 °C) or freezer over 15 °F (-9 °C) for 90+ minutes. The beep stops on its own once it recovers; the light keeps blinking. Press Alarm. Look for a door that did not latch, packed vents or a dirty condenser.
Door Alarm, Door Ajar A door or the freezer drawer stayed open 2 to 5 minutes (model dependent); it re-sounds every 2 minutes. Push in bins and shelves, and check the fridge is level so doors swing shut. Any key mutes it while you clean.
Door Open light on with doors shut French door units: a door switch or the left pantry control is failing.
Technician
Rule out something blocking a door first.
Cooling Off Cooling has been switched off, usually by a stray touch while wiping the panel. On many models hold Lock and Measured Fill together for 3 seconds.
Showroom Demo mode: lights on, compressor off. French door: hold Light and Lock 3 seconds. Built-in: hold Fridge and Freezer 3 seconds.
H2O, Water Filter, Air Filter Filter replacement reminders. Swap the filter and hold the reset key long enough for the light to change.

Flashing F and F#E# fault codes

Code Meaning Homeowner step
Flashing F The control has stored a fault, with or without a number shown.
Technician
Breaker off one minute, back on, confirm cooling is on, watch one minute. Note any code if it returns.
F3 E1, F3 E2, F3 E4, F3 E8, F3 E9, F3 EC Listed for French door models without a published meaning. In service literature the F3 family is the sensor group.
Technician
Reset once and give the exact code when you book.
F4 E1, F6 E1 Listed without a published meaning; F4 is generally the heater group and F6 the board-communication group.
Technician
Reset once, then book.
F8 E1, F8 E2, F8 E3, F8 E8 Listed without a published meaning; F8 is the ice system group.
Technician
Reset once, then book.
F8 EC Technicians commonly report it as a stalled or jammed ice maker module.
Technician
Break up any ice jammed in the bin or chute, reset the refrigerator, then book if it returns.

French door ice maker codes

Code Meaning Homeowner step
E0 No ice maker faults stored. Nothing to do.
E1 Ice bin sensor above 45 °F for over 3 hours.
Technician
Re-seat the bin and check the freezer door seal.
E2 Ice maker motor lost its home position, often from a jammed cube.
Technician
Turn the ice maker off, clear the jam, turn it on.
E3 Harvest heater timed out; after six failed harvests the ice maker pauses 24 hours.
Technician
Five minutes without power, then watch it. Returns? Book service.
E4, E5 Dry cycle without water (E4, rare), or ice maker sensor stuck above 16 °F while the bin sensor is cold (E5).
Technician
Make sure the supply valve is open and the water line is not frozen or kinked.

Readouts on specific models and in service mode

Display Meaning Homeowner step
Blinking C Some Whirlpool-built display models: fresh-food or freezer temperature sensor failed.
Technician
Five minutes without power, then watch it. Returns? Book service.
CF Some models: main board not talking to the user interface.
Technician
Five minutes without power, then watch it. Returns? Book service.
d Some models: the air damper between freezer and fresh food is stuck.
Technician
Five minutes without power, then watch it. Returns? Book service.
OP, SH Built-in models in service mode: a sensor is open (OP) or shorted (SH).
Technician
Five minutes without power, then watch it. Returns? Book service.
Sensor 01, 02, 03 Service-mode sensor test: pass (01), open (02), short (03).
Technician
Technician readout.
Inverter LED, 2 / 3 / 4 blinks Variable-speed compressor units: no speed signal from the board (2), inverter failure (3), compressor failure or sealed-system restriction (4). Read behind the rear access panel.
Technician
Leave the panel closed; sealed-system work is not DIY.

What we actually find on KitchenAid refrigerators in the Denver area

The codes above come from KitchenAid’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 51 KitchenAid refrigerator service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

Code Our calls What we found Part we used most
E5 1 Ice maker. —

The KitchenAid refrigerator repairs we do most often

Across all 51 KitchenAid refrigerator calls, with or without a code on the display:

  1. Control or inverter board: 6 calls
  2. Compressor or sealed system: 5 calls
  3. Defrost system: 3 calls
  4. Thermistor or sensor: 3 calls
  5. Ice maker: 2 calls
  6. Evaporator or condenser fan: 2 calls

Recent KitchenAid refrigerator calls

  • Westminster (80234), October 2026: KitchenAid refrigerator freezer not freezing. Diagnosis: control or inverter board.
  • Boulder (80304), September 2026: KitchenAid refrigerator leaking. Diagnosis: defrost system.
  • Thornton (80602), September 2026: KitchenAid refrigerator showing E5 and ice maker not working. Repair: ice maker replaced.
  • Broomfield (80023), June 2026: KitchenAid refrigerator ice maker not working. Repair: water inlet valve replaced.

KitchenAid refrigerator repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: KitchenAid refrigerator control or inverter board repair

Video by RepairClinic.com

What we see on Denver calls

  • The video shows a control or inverter board repair. It is the most common refrigerator repair on our calls.
  • The KitchenAid refrigerator repairs we do most often across the Denver metro and Boulder County: control or inverter board (6 calls), compressor or sealed system (5) and defrost system (3).
  • Recent call: Thornton (80602), September 2026: KitchenAid refrigerator showing E5 and ice maker not working. Repair: ice maker replaced.

Don’t want to do it yourself? Call 720-230-1229.

Before the technician arrives

  1. Write down exactly what the display shows, including the letters after F.
  2. Do the one-minute breaker reset once, not repeatedly.
  3. Check the panel does not say Cooling Off or Showroom.
  4. With power off, vacuum the grille and condenser coils at the bottom.
  5. Place a thermometer in each section: you want about 37 °F and 0 °F.

Signs you need service

  • The blinking F is back after the reset.
  • Either section stays warm for a day after you clean the coils and clear vents.
  • Frost covers the back wall of the freezer, or water pools under the crispers.
  • The compressor clicks on and off, or the unit is completely silent.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

KitchenAid refrigerator code FAQ

How do I reset a KitchenAid refrigerator code?

Cut power at the breaker or unplug it for one minute, then restore it. If the same code returns, the underlying part needs service.

What does PO mean on my KitchenAid?

The power went out long enough for the freezer to warm to about 18 °F. Acknowledge it and check your frozen food.

What do F3 E1 and F8 EC mean?

KitchenAid does not define them publicly. Technicians associate F3 codes with temperature sensors and F8 EC with a stalled ice maker module.

Sources: producthelp.kitchenaid.com, producthelp.kitchenaid.com, producthelp.kitchenaid.com, producthelp.kitchenaid.com, producthelp.kitchenaid.com, producthelp.kitchenaid.com, appliancemaestro.com, justanswer.com, searspartsdirect.com. Codes and meanings can vary by model; check your owner’s manual.

720-230-1229
720-230-1229

Photos from our job records

Real photos our technicians took on repair calls around Denver and the Front Range. Each caption says where the job was.

Refrigerator repair in Thornton, photo from our job records
Refrigerator repair in Thornton
Refrigerator repair in Westminster, photo from our job records
Refrigerator repair in Westminster
Refrigerator repair in Wheat Ridge, photo from our job records
Refrigerator repair in Wheat Ridge
Refrigerator repair in Arvada, photo from our job records
Refrigerator repair in Arvada
Call Now Book Online