LG Dryer Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

On LG dryers, d80, d90, and d95 mean the exhaust vent is 80 to 95 percent blocked and need the vent cleaned. nP and PS point to a power or wiring problem at the outlet or cord, and tE1, tE2, or tE3 are thermistor (temperature sensor) errors. A restricted vent is the most common cause and also a fire risk, so don't keep running the dryer with a d-code.

LG dryers show a code when airflow, power, heat, or the door isn't right. Vent codes are the ones homeowners see most, and they matter: a clogged vent slows drying and raises fire risk. The codes below come from LG support documentation and trusted repair-parts references. Not every code appears on every model, and gas and electric dryers differ in a few cases. The list combines the manufacturer's own code lists with service manuals and repair-parts references. Rows marked "on some models" or "service references" come from those repair sources, so the meaning can vary by model; check your owner's manual when in doubt.

LG Dryer error codes and what they mean

Code What it means What to try
d80 / d90 / d95 (also d75) Exhaust vent is restricted by about 75 to 95 percent. On some gas models, d80 can also indicate no gas supply. On models with a Flow Sense indicator, 2 or 4 lit bars also signal restricted airflow. The code shows for about 2 hours after the cycle. Unplug the dryer. Clean the lint filter and check the duct behind the dryer for kinks or crushing. Go outside and make sure the vent hood flaps open freely. Long or lint-packed duct runs usually need professional vent cleaning.
nP No current detected at the heater on electric models, usually a home wiring or breaker issue.
Call a technician
Confirm the dryer is plugged into a grounded 240V outlet. Turn the dryer's breaker off for at least 10 seconds, then back on. If it still won't heat, have an electrician check the outlet or a technician check the dryer.
PS Incorrect voltage in the power cord, often from the cord wires being connected wrong at the terminal block.
Call a technician
Reset the breaker for 10 seconds. Because the fix involves the power cord connection, have a qualified technician or electrician inspect it. Do not open the terminal block cover with power on.
tE1 / tE3 Thermistor (temperature sensor) error.
Call a technician
Unplug the dryer or switch off its breaker, hold Start/Pause for 5 seconds, then restore power and run a cycle. If the code returns, the sensor or wiring needs service.
tE2 Thermistor error during cold conditions. Common on steam cycles or in winter when the duct cools quickly.
Call a technician
In winter, clear snow and ice from the outside vent and confirm the flaps open fully. Try a power reset. If tE2 returns after a reset, schedule repair.
HS Humidity (moisture) sensor error. The dryer may run about 2.5 hours on a timed default and seem not to dry properly. Unplug the dryer. Wipe the two metal sensor bars inside the drum, below the lint filter, with a damp cloth and let them dry. Dryer sheet residue builds up here.
dE (also dE4) Door error. The door isn't fully closed or is misaligned. Push the lint filter all the way in and remove any clothing caught in the door. Power-cycle the dryer, close the door firmly, and start a cycle. If dE comes back, the door switch likely needs service.
PF Power failure, usually after an outage. Unplug the dryer or trip its breaker, hold Start/Pause for 5 seconds, then restore power and run a cycle.
gAS (may read "9A5") Gas dryer isn't receiving gas. LG lists this as a display message rather than a true fault.
Call a technician
Confirm the gas shutoff valve behind the dryer is fully open. If the dryer was just installed or moved, contact the installer. Never disconnect or repair gas lines yourself.
F0 / Insert Filter Lint filter isn't inserted correctly. Pull the lint filter out and push it back in fully.
E13 Drain error on hybrid condensing dryers only. Drain hose is kinked or clogged, or water in the sump is frozen. Check the drain hose for kinks or clogs and use only the standard LG hose. Press Start/Pause. If E13 returns, schedule repair.
Add Water Steam water supply is empty on steam models. Fill the steam feeder to the max line with tap water (not distilled) and close the drawer fully.
Check Filter Reminder to clean the lint filter. Not a fault. Clean the lint filter before every load.
CL Child Lock is on. Not a fault. Press and hold the Child Lock button for 3 seconds to unlock.
tE4 Temperature sensor (thermistor) error. On steam models, repair sources link it to the steam generator thermistor.
Call a technician
Unplug the dryer or trip its breaker for 30 seconds, then restart. If tE4 returns, the sensor or wiring needs a technician.
dHE Drying system error on LG washer-dryer combos. LG says it appears when the drying fan motor isn't working properly.
Call a technician
Unplug for about 5 minutes, then run a dry-only cycle. If dHE returns, stop using the unit and schedule service. Don't open panels; there is high voltage inside.
F1 Drum temperature too high, on ventless condenser and heat pump models. Unplug the dryer. Clean the lint filter, then clean the condenser: rinse a removable condenser, or gently vacuum a fixed heat pump condenser. Make sure the room isn't too hot or poorly ventilated.
LE / LE1 / LE2 Motor error on some models. LE1 means the motor stopped or is restricted; on heat pump models LE2 means a compressor or low-current problem.
Call a technician
Remove some laundry if the drum is overloaded. Unplug the dryer for 30 minutes, then restart. If the code returns, schedule repair.
AE Meaning varies by model. On heat pump dryers, AE usually means the compressor failed to restart. On some models, LG groups AE with lint filter sensor errors.
Call a technician
Unplug for 30 seconds and restart. Check that the lint filter is inserted fully and its magnet is intact. If AE returns, schedule repair.
OE Drain pump error on ventless condenser and heat pump models. Can also happen if the room is too cold.
Call a technician
Unplug and check that the drain hose isn't kinked, looped, or more than about 3 feet above the floor. Keep the dryer in a room above about 41°F. If OE repeats, schedule repair.
E05 Listed by LG without a description. Repair references describe it as a steam water supply problem on steam models (some sources print it as E5, a water supply pump error).
Call a technician
Open the water supply tap fully and check the inlet hose and its filter screen, or fill the steam feeder with tap water. If E05 returns, schedule repair.
E21 Listed by LG without a description. Depending on model, service references describe E21 as a gas ignition controller lockout (gas models), and other repair references as a drain or drain pump problem.
Call a technician
On gas models, check that the gas valve behind the dryer is fully open; do not work on the gas line yourself. On condensing models, check that the drain hose isn't kinked or clogged. Unplug for 5 minutes and restart. If E21 returns, schedule repair.
nE / nF Wi-Fi error on smart models. nE is a connection problem between the control and the Wi-Fi module; nF is a Wi-Fi module fault or registration issue. Drying still works. Restart the dryer and your router, then reconnect it in the LG ThinQ app. If the code stays, the Wi-Fi module may need service.
EE Main control memory (EEPROM) error.
Call a technician
Unplug the dryer for 10 minutes and restart. If EE returns, the control board likely needs service.
E1 / E2 / E3 / E4 (steam models) On steam models, repair references link these to the steam generator: E1 heater too hot, E2 water level sensor fault, E3 normal water level not reached, E4 heater temperature too low.
Call a technician
Make sure the steam water supply is on or the feeder is filled. Unplug for 5 minutes and restart. If it returns, schedule repair.
E24 On some models (service references): the airflow (pressure) switch did not turn on, meaning the dryer did not sense enough exhaust airflow.
Call a technician
Clean the lint filter and check the exhaust vent and outside hood for blockage. If E24 returns, schedule repair.
tE5 / tE6 / tE7 / tS2 On heat pump models (service references): thermistor faults at the water supply pump, compressor outlet, evaporator inlet or compressor discharge pipe.
Call a technician
Unplug the appliance for 5 minutes, then restart. If the code returns, write it down and call a technician.
LE3 / LE4 On heat pump models (service references): heater thermistor (LE3) or low-temperature evaporator thermistor (LE4) open or shorted.
Call a technician
Unplug the appliance for 5 minutes, then restart. If the code returns, write it down and call a technician.
CE1 On heat pump models (service references): compressor outlet temperature too high; the dryer shuts off and retries.
Call a technician
Clean the lint filters and the condenser area, and make sure the room is not too hot. If CE1 returns, schedule repair.
Empty Water On condensing and heat pump models: the water container is full or the pump is not emptying it. Empty the water container, or check the drain hose if the dryer drains to a standpipe.
dH / dS (some models) On some models (service references): dH means the thermistor temperature rose very fast (about 17 degrees in 10 seconds), often from restricted airflow; dS means a thermistor is open or shorted.
Call a technician
Clean the lint filter and vent. If the code returns, schedule repair.
ELE On some models (service references): earth leakage (ground fault) sensor error.
Call a technician
Stop using the dryer and have a technician check it. Do not work on the wiring yourself.
nC / nU On smart models (service references): NFC module error, usually seen only in test mode.
Call a technician
Unplug the appliance for 5 minutes, then restart. If the code returns, write it down and call a technician.
Ld Commonly reported: the load is too large for the moisture sensor to read accurately. Remove some items and restart.
CE (some models) Commonly reported as a control error, usually cleared by a power reset.
Call a technician
Unplug the appliance for 5 minutes, then restart. If the code returns, write it down and call a technician.

What we actually find on LG dryers in the Denver area

The codes above come from LG’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 113 LG dryer service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The LG dryer repairs we do most often

Across all 113 LG dryer calls, with or without a code on the display:

  1. Control board: 7 calls
  2. Clogged vent or lint: 7 calls
  3. Thermal fuse or thermostat: 5 calls
  4. Thermistor or sensor: 5 calls
  5. Idler pulley or drum rollers: 4 calls
  6. Drive belt: 3 calls
  7. Motor: 2 calls

Recent LG dryer calls

  • Longmont (80504), October 2026: LG dryer not starting. Repair: control board replaced (EBR86268009).
  • Lafayette (80026), September 2026: LG dryer not heating. Repair: thermal fuse or thermostat replaced.
  • Longmont (80501), August 2026: LG dryer stopping mid-cycle. Repair: motor replaced (4681EL1008K).
  • Denver (80230), June 2026: LG dryer not spinning. Repair: idler pulley or drum rollers replaced.

LG dryer repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: LG dryer error codes

Video by LG USA Support

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • The LG dryer repairs we do most often across the Denver metro and Boulder County: control board (7 calls), clogged vent or lint (7) and thermal fuse or thermostat (5).
  • Recent call: Longmont (80504), October 2026: LG dryer not starting. Repair: control board replaced (EBR86268009).

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. Unplug the dryer (or shut off its breaker) before any check. On gas dryers, don't touch the gas line or connector.
  2. Clean the lint filter, and the filter housing slot, before every load.
  3. Pull the dryer out carefully and look for crushed, kinked, or disconnected duct.
  4. Check the outside vent hood while the dryer runs; the flaps should open and you should feel strong airflow. In Denver winters, clear snow and ice from the hood.
  5. Wipe the moisture sensor bars inside the drum with a damp cloth.
  6. Do a power reset: unplug, hold Start/Pause for 5 seconds, then plug back in.

When to call a technician

  • nP or PS codes, or the dryer runs but won't heat.
  • tE codes return after a reset.
  • d-codes continue after you've cleaned the filter and checked the duct.
  • You smell gas, burning, or scorching. Stop using the dryer; for a gas smell, leave the house and call your gas utility first.
  • dE returns with the door fully closed.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

What does d80 mean on an LG dryer?

d80 means the exhaust vent is about 80 percent blocked. d90 and d95 mean it's even more restricted. Clean the lint filter, check the duct for kinks, and have the vent cleaned if the code continues.

Why does my LG dryer show tE2 in winter?

tE2 is a temperature sensor error that often appears in cold conditions, when the duct and sensor cool quickly. Clear snow or ice from the outdoor vent, try a power reset, and call for service if it keeps returning.

Is it safe to keep using my LG dryer with a d90 or d95 code?

It's not a good idea. A heavily restricted vent makes the dryer run hot and long and lets lint build up, which is a fire risk. Clean the vent before using it again.

How do I reset an LG dryer?

Unplug the dryer or turn off its breaker. Hold Start/Pause for 5 seconds, then restore power and start a cycle.

Sources: lg.com, lg.com, lg.com, lg.com, lgparts.com, coolblue.be, homeserve.com, lg.com, mypros.plus, appliancemaestro.com. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229
Call Now Book Online