The most common LG washer codes are OE (not draining), IE (not filling), UE (unbalanced load), and dE (door or lid not locked). Most of these clear after you fix the hose, filter, load, or door and restart. Codes like LE, CE, PE, tE, and FE that keep coming back after a reset usually point to a failed part that needs a technician.
LG washers show a two- or three-character code when something stops a cycle. Some codes mean a simple fix, like a kinked hose or a lopsided load. Others point to a sensor, motor, or control problem. The table below covers LG front-load, top-load, and SideKick pedestal washer codes from LG support documentation and trusted repair-parts references. Exact codes vary by model, so check your owner's manual if your display shows something not listed. The list combines the manufacturer's own code lists with service manuals and repair-parts references. Rows marked "on some models" or "service references" come from those repair sources, so the meaning can vary by model; check your owner's manual when in doubt.
LG Washer error codes and what they mean
| Code | What it means | What to try |
|---|---|---|
OE (may read 0E) |
Drain error. The washer can't drain water in time. | Unplug the washer. Straighten any kinked drain hose and check it isn't clogged or frozen. On front-loaders, clean the drain pump filter behind the lower front panel (have towels ready). On SideKick pedestals, keep the drain height under 53 inches. |
IE (may read 1E) |
Inlet error. Not enough water is coming in. | Make sure both faucets are fully open and the inlet hoses aren't kinked. Shut off the water and clean the small screen filters where the hoses connect. Check that other faucets in the house have good pressure. |
UE / uE / Ub |
Unbalanced load. The washer can't spin evenly. | Redistribute the clothes. For a single heavy item or a very small load, add one or two similar items. Top-loaders retry balancing on their own a few times before pausing. |
dE / dE1 / dE2 / dE4 |
Door error on front-loaders. dE1 means the door isn't closed properly; dE2 means it's closed but didn't latch. | Remove any clothing caught in the door gasket and close the door firmly. Reset: turn the washer off, unplug it, hold Start/Pause for 5 seconds, then plug back in. If it returns, the latch or lock may be bad. |
dE (top-load) |
Lid isn't closed properly. | Check for anything caught under the lid, close it fully, and press Start/Pause. If the lid is closed and the code stays, the lid lock likely needs service. |
LE |
Locked motor. The motor is overloaded or can't turn. Call a technician |
Let the washer rest for 30 minutes, then restart. Reduce an oversized load. On SideKick models (LE1), check for coins or objects stuck under the pulsator. Repeated LE codes point to a motor or wiring fault. |
CE (may read cE) |
Motor over-current, an electrical fault in the motor circuit. Call a technician |
Unplug for 10 seconds and try a cycle. If CE returns, close the water faucets, leave the washer unplugged, and schedule repair. |
PE |
Water level (pressure) sensor error. Call a technician |
Unplug for about 15 seconds, hold Start/Pause for 5 seconds, then plug in and restart. Too much detergent can also contribute. If PE comes back, the sensor or its hose needs service. |
FE |
Fill or overflow error. Water is above the safe level, often from an inlet valve that won't close. Call a technician |
Turn off both water faucets. Run a drain or spin-only cycle to remove the extra water, then leave the washer unplugged until it's repaired. |
tE (also tE1 to tE6) |
Temperature sensor (thermistor) error. Call a technician |
Try a power reset. If the code persists, the thermistor or its wiring needs to be tested by a technician. |
Sud (may read 5ud or "Cod Sud") |
Too many suds detected. Not a fault. | The washer adds a suds-reducing routine that can add about 2 hours. Use less HE detergent next time. |
FF |
Freeze error. Water in the hoses, pump, or valve is frozen. | Check the inlet and drain hoses and the drain filter. Pour warm (not boiling) water into the drum and wrap the supply hose valve area with a warm, wet towel. |
PF |
Power failure. Power was interrupted during a cycle. | Restart the cycle. If PF shows up often, have the outlet and circuit checked. |
EE |
Main control board memory (EEPROM) error. Call a technician |
Unplug the washer for 10 minutes. If the code returns, the control board may need replacement. |
E6 (SideKick) |
Clutch error. An object such as a coin is likely stuck between the pulsator and tub. | Empty the tub and look along the pulsator seam for coins, zippers, or clips. Unplug the unit before removing anything. |
Ed / Ed1 / Ed2 / Ed3 / Ed4 / Ed5 / OPn |
Easy Dispense or detergent drawer problem on models with auto-dispense. Ed1/Ed2: detergent pump fault or open circuit. Ed3/Ed4: softener pump fault or open circuit. Ed5: dispenser communication fault. OPn means the drawer isn't fully closed. | Push the detergent drawer fully closed and restart. Numbered Ed codes (Ed1 to Ed5) point to a dispenser pump or board fault. |
tCL |
Tub Clean reminder. Not a fault. | Run the Tub Clean cycle with the drum empty, using a washer cleaner or diluted bleach as your manual directs. |
CL |
Child Lock is on. Not a fault. | Press and hold the Child Lock button (or button pair shown on your panel) for 3 seconds to unlock. |
AE |
Meaning varies by model. On many front-load models, AE is a leak (anti-flood) error: water was detected in the base pan. On some top-load models, LG groups AE with LE1 as a rotation error, where the drum or motor can't turn freely. Call a technician |
Unplug the washer and shut off both faucets. Front-load: check the fill and drain hose connections and the door seal for drips, and use only HE detergent. Top-load: look for a coin or small object stuck between the wash plate and tub. If water is in the base and no outside hose is leaking, the leak is internal. |
LE1 |
On top-load and some other models, a foreign object is stuck in the tub or the drum can't rotate freely. | Unplug the washer, empty the tub, and check around the wash plate (pulsator) for coins, clips, or wires. If the code or a grinding noise continues, schedule repair. |
SE |
Motor hall (speed) sensor error on front-load models. The control can't read motor speed. Call a technician |
Unplug for a few minutes and restart. If SE returns, the sensor, motor wiring, or control board needs a technician. |
HE |
Heater error on models with an internal water heater or drying heater, such as washer-dryer combos and some front-loaders. Water or air isn't heating as expected. Call a technician |
Unplug for 10 seconds and restart. If HE comes back, or you notice a burning smell, stop using the washer and leave it unplugged. Heater diagnosis needs a technician. |
dHE |
Drying system error on LG washer-dryer combos. LG says it appears when the drying fan motor isn't working properly. Call a technician |
Unplug the washer for about 5 minutes, plug it back in, and run a dry-only cycle. If dHE returns, LG advises not using it for wash or spin until it's inspected. Don't open panels; there is high voltage and heat inside. |
dL |
Door (lid) not locked, on some top-load models. | Unplug and check the lock on the lid for lint, debris, or a caught item. Close the lid firmly and restart. Avoid running the washer in a very humid, unvented room. If dL continues, the lid lock or switch needs service. |
E3 |
Meaning varies by model. On some LG top-load models it's a drain motor error; on some older front-load models it's a heating or temperature sensor error. Call a technician |
Unplug the washer, plug it back in, and retry. In cold weather, thaw the tub and drain hose with warm (not boiling) water. If E3 repeats, schedule repair. |
E1 / E2 / E4 / E5 (older models) |
Older LG washers use number codes. E1 matches IE (fill error), E2 matches OE (drain error), E4 matches FE (overfill), and E5 matches dE (door error). On some older models, repair references list E3 as overheating or a temperature sensor fault and E6 as a clutch or motor fault. | Follow the steps for the matching letter code: IE for E1, OE for E2, FE for E4, and dE for E5. |
vS / uS / v5 (may read u5) |
Vibration sensor error, mainly on top-load and WashTower models. Call a technician |
Press Start/Pause to resume. If it recurs, turn the washer off and back on. Make sure the washer is level and not touching a wall. If the code persists, schedule repair. |
Eb |
Clutch error, on some top-load models. Call a technician |
Unplug the washer for a few minutes and restart. If Eb returns, the clutch or shifter needs a technician. |
nE / nF |
Wi-Fi error on smart models. nE means the Wi-Fi module isn't connected; nF means the Wi-Fi modem failed its self-check. Washing still works. | Restart the washer and your router, then reconnect the washer in the LG ThinQ app. If the code stays, the Wi-Fi module may need service. |
Cd |
Cool Down on washer-dryer combos. Not a fault; the drum is cooling after a dry cycle. | Let the cycle finish. Opening the door early stops the cool-down. |
Dr / drn |
Drain notice on some top-load models. Not a fault; the washer drained after being paused for more than about 4 minutes. | Press Start/Pause to continue the cycle. If it stays on drn for more than a few minutes, follow the OE steps. |
LO |
On some models, repair references list LO as a door unlock failure: the door lock did not release at the end of the cycle. Call a technician |
Unplug the washer for 5 minutes, make sure the tub has drained, then try the door again. Never force the door. If LO returns, call a technician. |
LE2 / LE3 |
On some models (service references): LE2 means the drum motor or impeller is restricted; LE3 a fan motor lock on washer-dryer combos. Call a technician |
Unplug the appliance for 5 minutes, then restart. If the code returns, write it down and call a technician. |
dCE |
On some top-load models (service references): a coin or other object is stuck, causing a motor problem. Call a technician |
Unplug the washer and look for objects between the wash plate and tub. If you can't free it, call a technician. |
Stuc |
On some top-load models (service references): a foreign object is stuck in the wash plate. | Unplug the washer and remove any object under or around the wash plate. |
dE3 (some models) |
On some models (service references): lid or door detection error. Call a technician |
Close the door or lid firmly and restart. If it returns, call a technician. |
PE1 / PC1 (top-load) |
On some top-load models (service references): clutch sensor error. Call a technician |
Unplug the appliance for 5 minutes, then restart. If the code returns, write it down and call a technician. |
nC / nU |
On smart models (service references): NFC module error (nC) or NFC version error (nU), usually seen in test mode. Call a technician |
Unplug the appliance for 5 minutes, then restart. If the code returns, write it down and call a technician. |
dn / HS / StackE (SideKick) |
On SideKick pedestal washers (service references): the pedestal was started without the main washer connected or powered. | Make sure the main washer is plugged in and powered on, then restart the pedestal. |
What LG washer error codes actually turned out to be on our service calls
The code table above is what LG’s manual says. This section is what our technicians found when they opened the machine. Since 2024 we have serviced 220 LG washers across the Denver metro, Boulder County and the Longmont area, and 36 of those calls started with an error code on the display. Every number below comes from our own job records.
| Code | Our calls | What we found | Part we installed most |
|---|---|---|---|
| OE (won’t drain) | 12 | A failed drain pump in most cases. We replaced the pump on most of these calls. | Drain pump 4681EA2001T |
| LE (motor locked) | 6 | Usually a bad rotor position (Hall) sensor. Once it was worn drum bearings, and once a failing main board. | Hall sensor 6501KW2002A |
| UE (unbalanced) | 1 | Worn suspension rods. | Suspension rod kit 4902FA1665W |
| U5 | 1 | The control board had to be replaced. | Main control board |
The LG washer repairs we do most often
Across all 220 LG washer calls, with or without a code, these were the repairs we did most:
- Drain pump: 41 repairs. This is the most common LG washer failure we see by a wide margin.
- Water leaks from the pump, hoses or door area: 24.
- Shock absorbers and suspension: 17. These are behind loud banging on spin.
- Control or display board: 16.
- Water inlet valve: 15.
- Hall sensor: 9. This is behind most LE codes.
- Coins and other objects in the pump or drum: 7.
- Drum bearings: 7.
What our technicians tell LG owners
- If OE comes back after you clean the filter and check the hose, plan on a pump. Most of our 12 OE calls ended with a new drain pump (4681EA2001T), not a cleaning.
- Rugs and bath mats are hard on the pump. One washer stopped draining right after a carpet wash because the drain filter was clogged with fibers.
- Grinding on spin is not always the bearings. On one LG washer the grinding turned out to be a coin, and we took it out.
Recent LG washer calls
- Boulder (80301), September 2026: A stackable LG washer showed LE. We replaced the Hall sensor (6501KW2002A).
- Longmont (80504), September 2026: OE code and a loud noise. We replaced the drain pump (4681EA2001T).
- Longmont (80501), July 2026: OE code with the door stuck locked. The drain pump had failed, and we replaced it.
- Lyons (80540), October 2026: U5 error on the display. Diagnosis: the main control board needs replacing.
LG washer repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.
Source: The Appliance Team service records, 2024–2026. Customer details removed.
Video: LG washer error codes
Video by LG USA Support
What we see on Denver calls
- An error code points to the system that reported the fault, not always to the part that failed.
- The video covers the OE (won’t drain) code. On our calls OE was the most common LG washer code: 12 calls, and in most cases the drain pump had failed (4681EA2001T).
- Across all 220 LG washer calls, the drain pump was the most common repair: 41 repairs. Water leaks from the pump, hoses or door area came next: 24.
Don’t want to do it yourself? Call 720-230-1229.
What you can safely check yourself
- Unplug the washer and shut off both water faucets before touching hoses, filters, or the drain pump.
- Do a full reset: unplug the washer, hold Start/Pause for 5 seconds, then plug it back in.
- Check the inlet hoses for kinks and clean the screen filters at the hose connections.
- Clean the front-load drain pump filter; set out towels and a shallow pan first.
- Use only HE detergent and measure it. Denver's hard water can make people overdose detergent, which leads to Sud and PE codes.
- Rebalance the load and make sure nothing is caught in the door gasket or lid.
When to call a technician
- LE, CE, PE, tE, or EE returns after a reset.
- FE appears or the washer keeps filling while turned off.
- dE codes persist with the door fully closed, which suggests a failed door lock.
- OE continues after the hose and drain filter are clear, which points to the drain pump.
- You see water leaking from under the washer or smell burning.
How to prevent this
Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:
Frequently asked questions
How do I reset an LG washer error code?
Turn the washer off and unplug it (or switch off its breaker). With power off, press and hold Start/Pause for 5 seconds, then plug it back in and start a new cycle. If the same code returns, the underlying problem is still there.
Why does my LG washer keep showing UE?
UE means the load is unbalanced. It's common with a single heavy item like a rug or comforter, or very small loads. Add similar items or redistribute the load; if UE appears with normal loads, the shock absorbers or suspension may be worn.
What does OE mean on an LG front-load washer?
OE means the washer isn't draining. The most common causes are a clogged drain pump filter or a kinked drain hose. If both are clear and OE continues, the drain pump may have failed.
Is the Sud code an error?
No. Sud means the washer detected excess suds and added a routine to break them down, which can add about two hours. Using less HE detergent prevents it.
Sources: lg.com, lg.com, lg.com, lg.com, lgparts.com, lg.com, lg.com, lg.com, lg.com, lg.com, whitegoodshelp.co.uk, partstown.com, beaconsaves.com, lg.com, mypros.plus. Codes and meanings can vary by model; check your owner's manual.