Monogram Oven Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

Monogram ovens speak GE’s code language. F3 or F4 is the temperature sensor, F2 is an overheat, F9 or FC is the door lock circuit, and F0, F1, F6 or F7 is the touch keypanel. GE’s own instruction is to switch the breaker off for a minute or two; if the code comes back, leave the oven off at the breaker and book a repair.

Monogram is GE’s luxury line, and its wall ovens, ranges and Advantium speed ovens run GE electronic controls. That means GE’s published code list applies directly, and we have supplemented it with model notes from repair references (marked “commonly reported”). Several displays are not failures at all, including LOC, OFF and a reversed C. Monogram is mostly built-in and dual-fuel equipment, so be careful: switch off the breaker before any check, and on a dual-fuel range close the gas before the range is moved.

Monogram oven codes

Heat and temperature sensing

Display Monogram / GE meaning Next step
F2, F20 Overheat: the cavity exceeded its preset limit.
Technician
Breaker off, let it cool, do not use until inspected.
F3, F4 Oven sensor fault; F3 is commonly an open sensor and F4 a shorted one.
Technician
Breaker off a minute or two; a repeat means a service visit. The sensor is usually replaced.
FD Meat probe or probe socket. Pull the probe, make sure the socket is clean and dry. Code without the probe inserted means service.
F350 Upper cooling fan circuit, or something obstructing the fan.
Technician
Turn the oven off and book.

Keypanel and control

Display Monogram / GE meaning Next step
F0, F1, F6, F7 Touch keypanel fault, such as a stuck or shorted key.
Technician
Clean and dry the glass, then breaker off a minute or two; a repeat means a service visit. The keypanel is the usual repair.
F5, F8, FF Electronic control fault.
Technician
Breaker off a minute or two; a repeat means a service visit.
F96, F97, F7X Internal component failure. On Advantium units F97 is commonly reported as a cooling fan failure.
Technician
Breaker off a minute or two; a repeat means a service visit.
ERR The control did not accept a setting. Enter it again.

Door lock and self-clean

Display Monogram / GE meaning Next step
F9, FC A component in the lock circuit has failed.
Technician
Let the oven cool fully, reset at the breaker. Still locked? Book.
Unlock Door The latch did not release after self-clean. Wait until cold, then follow GE’s control reset steps.
LOC DOOR (flashing) Shows even though self-clean was not chosen. Breaker off a minute or two.
OFF Too hot to start self-clean, or still cooling after one. Wait and try again.

Advantium, wiring and normal messages

Display Monogram / GE meaning Next step
F6, F76 (Advantium) Commonly reported: halogen lamp circuit open (F6) or magnetron fault (F76).
Technician
Do not open the cabinet; microwave components store high voltage.
Bad Line Power is present but wired incorrectly.
Technician
An installer or electrician must fix the connection.
LOC Control lockout is on. Turn it off per the manual.
Reversed C Sabbath mode. Exit Sabbath per the manual.

What we find on Monogram ovens and similar ovens in the Denver area

We see fewer Monogram ovens than the big-volume brands: 1 service call in our records since 2024. The parts that fail are much the same across brands, so here is what we found on all 645 oven calls in our records since 2024.

The oven repairs we do most often (all brands)

  1. Control board: 54 calls
  2. Igniter: 45 calls
  3. Bake or broil element: 26 calls
  4. Surface element or burner switch: 20 calls
  5. Wiring: 16 calls
  6. Convection fan: 15 calls
  7. Temperature sensor: 13 calls

Recent oven calls

  • Erie (80516), October 2026: Oven not starting. Repair: igniter replaced.
  • Littleton (80123), October 2026: Oven not starting. Repair: bake or broil element replaced (5304521190).
  • Broomfield (80020), September 2026: Oven not heating. Diagnosis: wiring.
  • Golden (80403), September 2026: Oven not heating. Repair: bake or broil element replaced (WPY04100021).

Oven repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2024–2026. Customer details removed.

Owner steps for a Monogram oven code

  1. Record the code and whether it shows on the upper or lower oven.
  2. Turn off the oven breaker for a minute or two, then restore power.
  3. Clean and dry the touch panel if a key code appears.
  4. For FD, remove the probe and dry the socket.
  5. Wait for a cold oven before dealing with a locked door.

Arrange a repair when

  • F2 appears or the oven runs hotter than set.
  • F3, F4, F9, FC or a control code survives the reset.
  • The door stays locked once cold, or F350 shows.
  • Bad Line appears after an install or a move.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Monogram oven code FAQ

How do I clear a Monogram oven code?

Switch off the oven’s breaker for a minute or two. If the same code comes back, keep the breaker off and schedule service.

What does F3 mean on a Monogram wall oven?

The oven temperature sensor circuit is open. Replacing the sensor is the usual fix.

What does F9 mean?

A part in the door lock circuit has failed. Let the oven cool before trying anything.

Why does my Monogram say LOC?

The control lockout is on. It is a feature, not a fault.

Sources: products.geappliances.com, appliancefactoryparts.com, appliancepartspros.com. Codes and meanings can vary by model; check your owner’s manual.

720-230-1229
720-230-1229
Call Now Book Online