Samsung Dryer Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

The most common Samsung dryer codes are temperature and heating codes (tS, tE, tC, HC, hE), which usually mean a clogged lint screen or exhaust vent. Door codes (dC, dE, dF) mean the door is not detected as closed. If cleaning the lint screen and vent does not clear a heat code, or motor, communication or gas ignition codes keep returning, a technician should diagnose it.

Samsung dryers show a short code on the display when they detect a problem. Several codes often mean the same thing, depending on the model. One tip from Samsung: an upside-down "F" on the display is actually a "t", so "FS" is really tS. Unplug an electric dryer, or unplug a gas dryer and leave the gas line alone, before any hands-on check. The list combines the manufacturer's own code lists with service manuals and repair-parts references. Rows marked "on some models" or "service references" come from those repair sources, so the meaning can vary by model; check your owner's manual when in doubt.

Samsung Dryer error codes and what they mean

Code What it means What to try
tS / t5 / tC / tO / tE / tE3 / tC5 Temperature or temperature sensor problem. Clean the lint screen and the exhaust vent from the dryer to the outside hood. A restricted vent is the most common cause. If the code continues, a technician should test the thermistor and wiring.
t0 / tCS / 1 tC / 1tC5 / 1tCS Temperature or temperature sensor error variants, same as the row above. Clean the lint screen and the full exhaust vent. If the code continues, a technician should test the thermistor and wiring.
tE5 Compressor temperature sensor problem on heat pump (ventless) models (shown as tC5 on some models).
Call a technician
Power off for 2-3 minutes, clean the lint filter, and restart. If it returns, request service.
FIL + tEr On heat pump (ventless) models: the heat exchanger needs cleaning. Clean the heat exchanger as your manual describes. If the message returns right after cleaning, request service.
NC / NC1 Lint filter problem on some heat pump (ventless) models. Remove the lint filter, clean it, and reseat it fully. If the code remains, request service.
NC2 Heat exchanger cover problem on some heat pump (ventless) models. Check that the heat exchanger cover is in place and fully latched. If the code remains, request service.
HC / hE / HC4 / 1 HC The dryer is overheating, or on electric models, not heating enough.
Call a technician
Clean the lint screen and vent thoroughly. On electric dryers, low supply voltage can cause weak heat; have an electrician check the outlet. If the code returns, the heating system needs service.
HC2 Gas ignition error (gas models).
Call a technician
Power off for 2-3 minutes and restart the cycle. Do not work on the gas valve, burner or gas line yourself. If it returns, request service.
HC (heat pump models) On heat pump (ventless) models: the compressor has overheated.
Call a technician
Clean the lint filter and heat exchanger, make sure the room is not too hot or enclosed, and check that the breaker has not tripped. If it returns, request service.
dC / dE / dF / do / d0 / 1 dC / 1 dF Door, latch or door sensor problem. Make sure no laundry is caught in the door and that it closes fully and latches. If the latch or door switch is damaged, it needs replacement.
5C / 5E On heat pump (ventless) models: drain problem. The water tank may be full, the drain hose kinked or frozen, or the pump faulty. Empty the water tank. Check the drain hose for kinks. If the hose is frozen, wrap it in a towel soaked in warm water for about 10 minutes. If the code remains, request service.
9C1 / 9E / 2E / 9E1 Abnormal voltage supplied to the dryer. Plug the dryer into its own circuit with no extension cord. On stacked units with a multi-control kit, a SmartThings update can fix this. If it persists, have the circuit checked.
9C2 / 9E2 Power supply error: voltage is low or irregular. Make sure the cord is fully plugged in and the dryer is on its own circuit with no extension cord. If it continues, have the circuit checked.
bE / bE2 / bC2 / 6E / 6E2 / 6C2 A control panel button is stuck or held down. Turn the dryer off, then press and release each button, including its edges. If a button is damaged or the code returns, the panel needs service.
AC / AE / Et / EEE / AE3 / AE4 / AE5 / E3 / CA / 1 AC / 1 AC7 Internal components cannot communicate.
Call a technician
Turn the dryer off for 60 seconds, then back on. If the code remains, request service.
AC4 Communication error between the main control board and the Wi-Fi board.
Call a technician
Turn the dryer off for 60 seconds, then back on. If the code remains, request service.
AC6 / AE6 Communication error between the main control board and the motor inverter board.
Call a technician
Restart the cycle. If the code remains, request service.
FC / FE / 1 FC Power source frequency is invalid.
Call a technician
Restart the cycle. If the code remains, request service.
Clg / Cg Vent blockage test result: the vent is clogged. Clean the lint screen and the full exhaust vent run, including the outside hood flap.
C80 / C8 / C8o Vent blockage test result: vent about 80% blocked. Clean the exhaust vent. A blocked vent slows drying and raises the fire risk.
C90 / C9 / C9o / Cl9 Vent blockage test result: vent more than 90% blocked. Stop using the dryer until the vent is cleaned. Long or crushed vent runs may need a professional cleaning.
C1 / CL1 Laundry detected in the drum during the vent test. Empty the drum and run the test again. If it shows with an empty drum, request service.
Ct The dryer is below freezing or above 104 F. Let the dryer sit at room temperature for an hour, then retry. Useful to know for unheated Denver garages in winter.
CL Child Lock is on. Not a fault. Turn Child Lock off using the button combination in your manual.
dn Firmware download in progress. Do not unplug or turn off the dryer. If dn still shows after 24 hours, request service.
3C Motor error.
Call a technician
Power off for 2-3 minutes and restart. Check that the drum is not overloaded. If it returns, the motor or its control needs service.
3C1 On heat pump (ventless) models: the drum is overloaded. Remove some laundry and restart. Dry bulky items in smaller loads.
3E / 3C2 / 3C3 / 3C4 / 3C5 / 3C6 / 3C7 / 3C8 Drive motor or inverter motor error.
Call a technician
Power off for 2-3 minutes and restart. Check that nothing is jamming the drum. If it returns, the motor or its control needs service.
oD / od / dt Dry time error.
Call a technician
Clean the lint screen and vent, power off for 2-3 minutes and restart. If it returns, request service.
0 (vent test) Vent blockage test result: the vent is in good condition. Not a fault. No action needed.
HC5 On heat pump (ventless) models: the compressor stopped three times because of high temperature.
Call a technician
Clean the lint filter and heat exchanger filter, and make sure the room is not too hot. Restart. If HC5 returns, call a technician.
tC2 / tE2 Repair references list these as a temperature sensor (thermistor) reading out of range.
Call a technician
Unplug the appliance for 5 minutes, then restart. If the code returns, write it down and call a technician.
tC4 Repair references list tC4 as the drum motor inverter (IPM) temperature sensor fault.
Call a technician
Unplug the appliance for 5 minutes, then restart. If the code returns, write it down and call a technician.
tC7 / tC8 / tCA / tE4 Repair references list these on heat pump models as additional thermistor faults (thermistors 2 to 5).
Call a technician
Unplug the appliance for 5 minutes, then restart. If the code returns, write it down and call a technician.
tC9 Repair references list tC9 on heat pump models as a compressor inverter (IPM) temperature sensor fault.
Call a technician
Unplug the appliance for 5 minutes, then restart. If the code returns, write it down and call a technician.
3CA / Repair references list these on heat pump models as a compressor inverter motor fault.
Call a technician
Unplug for 5 minutes and restart. If it returns, the sealed system and inverter need a technician.
9CA1 / 9CA2 Repair references list these on heat pump models as a power supply fault at the compressor inverter.
Call a technician
Check that the dryer is on its own outlet and not an extension cord. If it returns, call a technician.
ACA Repair references list ACA on heat pump models as a communication error between the main board and the compressor inverter board.
Call a technician
Unplug the appliance for 5 minutes, then restart. If the code returns, write it down and call a technician.
EE / EEprom / EEprom Fail Repair references list these as a control board memory (EEPROM) error.
Call a technician
Unplug the appliance for 5 minutes, then restart. If the code returns, write it down and call a technician.
E1 (older models) Older Samsung dryer code: thermistor or thermistor circuit short.
Call a technician
Clean the lint screen and vent, then restart. If E1 returns, call a technician.
EH Repair references list EH as a heating error.
Call a technician
Clean the lint screen and check the vent. On gas models make sure the gas valve is on. If EH returns, call a technician.
2E (some models) On some models repair references describe 2E as the dryer stopping temporarily, with all buttons except Power not responding (Samsung groups 2E with voltage errors). Turn the dryer off, unplug it for 5 minutes and restart. If it returns, have the outlet voltage checked.
3E (some models) Repair references list 3E on older models as a fault in the motor relay circuit.
Call a technician
Unplug the appliance for 5 minutes, then restart. If the code returns, write it down and call a technician.
dO dE Repair references list this as the door being open while the dryer is running. Close the door firmly and restart.

What we actually find on Samsung dryers in the Denver area

The codes above come from Samsung’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 126 Samsung dryer service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The Samsung dryer repairs we do most often

Across all 126 Samsung dryer calls, with or without a code on the display:

  1. Heating element: 20 calls
  2. Thermal fuse or thermostat: 5 calls
  3. Clogged vent or lint: 4 calls
  4. Idler pulley or drum rollers: 3 calls
  5. Thermistor or sensor: 3 calls
  6. Control board: 3 calls

Recent Samsung dryer calls

  • Arvada (80005), September 2026: Samsung dryer not heating. Repair: heating element replaced.
  • Denver (80221), September 2026: Samsung dryer making noise. Repair: motor replaced.
  • Arvada (80002), August 2026: Samsung dryer not heating. Repair: thermal fuse or thermostat replaced.
  • Brighton (80601), August 2026: Samsung dryer stopping mid-cycle. Repair: heating element replaced.

Samsung dryer repairs from $280. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Samsung dryer error codes

Video by Parts Dr

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • The Samsung dryer repairs we do most often across the Denver metro and Boulder County: heating element (20 calls), thermal fuse or thermostat (5) and clogged vent or lint (4).
  • Recent call: Arvada (80005), September 2026: Samsung dryer not heating. Repair: heating element replaced.

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. Unplug the dryer before any hands-on check. On gas dryers, never disconnect or adjust the gas line.
  2. Clean the lint screen before every load and wash it with warm soapy water if it looks clogged.
  3. Disconnect and clean the exhaust duct and check the outside vent flap opens freely.
  4. Replace crushed or plastic foil duct with rigid or semi-rigid metal duct.
  5. Check that nothing is caught in the door and that it latches firmly.
  6. Plug the dryer directly into its own outlet with no extension cord.
  7. Power off for 2-3 minutes, then restart the cycle once to see if the code clears.

When to call a technician

  • A heat or temperature code returns after the lint screen and vent are clean.
  • You see a gas ignition code (HC2) or smell gas. If you smell gas, leave the home and call the gas utility first.
  • The dryer runs but stays cold, or it gets too hot to touch.
  • Motor, communication or frequency codes keep coming back after a reset.
  • The door latch or a control button is broken.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

How do I reset a Samsung dryer error code?

Turn the dryer off and unplug it or switch off the breaker for 2-3 minutes, then power it back on and start a cycle. If the cause is still there, the code will return.

What does tS or FS mean on a Samsung dryer?

It is a temperature sensor code. Samsung notes that the upside-down F on the display is a t. Clean the lint screen and vent first; if it continues, the sensor or wiring needs service.

Why does my Samsung dryer show HC?

HC means the dryer is overheating, or on electric models, not getting enough heat. A clogged vent is the usual cause, so clean the lint screen and the full vent run before calling for service.

What do C80 and C90 mean on a Samsung dryer?

They are vent blockage test results. C80 means the vent is about 80% blocked and C90 means more than 90% blocked. Clean the vent before using the dryer again.

Sources: samsung.com, samsung.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, samsung.com, mypros.plus. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229

Photos from our job records

Real photos our technicians took on repair calls around Denver and the Front Range. Each caption says where the job was.

Dryer repair in Mead, photo from our job records
Dryer repair in Mead
Dryer repair in Morrison, photo from our job records
Dryer repair in Morrison
Dryer repair in Niwot, photo from our job records
Dryer repair in Niwot
Dryer repair in Northglenn, photo from our job records
Dryer repair in Northglenn
Call Now Book Online