Washer Door Gasket Mold: Clean or Replace?

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

Wipe and dry the door gasket (also called the door boot or bellow) every week and leave the door open after every wash. If black spots wipe off, cleaning is enough. If they stay in the rubber after a bleach cleaning, if the boot is torn, or if the odor comes back after several tub cleans, the gasket should be replaced. A moldy gasket touches every load you wash.

Why mold grows in the door gasket

The rubber gasket seals the door of a front-load washer. Its folds hold a little water after every cycle, plus lint, hair, detergent and fabric softener residue. Dark, damp and full of food for microbes, it’s the perfect place for mold and bacteria.

This isn’t just a theory. A 2023 study in Scientific Reports sampled 50 washing machines and found fungi in 82% of them. The inner part of the rubber door seal was the most often colonized spot, with Aspergillus and the black mold Cladosporium among the most common.

This guide is part of our washer maintenance checklist. On the same appliance, also check washer tub cleaning and odor prevention and washer drain pump filter cleaning. Related guides for other appliances: commercial washer door, gasket and drain care and dishwasher door gasket and drain hose care.

!

What happens if you ignore a moldy gasket

Mold in the boot doesn’t stay in the boot. Every load you wash rubs against it and rinses through it.

1

Residue builds in the folds Early

Inside: Water, lint, hair and detergent or softener residue collect at the bottom of the gasket.

You notice: A gray film or slimy feel in the folds.

2

Mold and bacteria grow Growing

Inside: Black and gray spots appear and spread around the fold.

You notice: Musty smell when you open the door, black specks in the rubber.

3

It reaches your laundry Serious

Inside: Clothes and towels touch the gasket every cycle, and rinse water flows over it.

You notice: Clean laundry smells musty, towels smell sour after drying, gray or black specks on fabric.

4

Mold grows into the rubber Severe

Inside: Spots that are left for months stain the rubber and can’t be fully cleaned out. Debris and coins wear holes in the boot.

You notice: Black spots that stay after bleach, small tears or holes.

5

Leaks and replacement Critical

Inside: A torn or hardened boot leaks during the wash and spin.

You notice: Water at the front of the washer, odor that never goes away.

What it can cost you

Musty-smelling clothesStained laundryAllergy and asthma triggersDoor boot replacementLeaks and floor damage

Worst caseA washer that makes “clean” laundry smell and spreads mold onto clothes, towels and bedding, plus a torn boot that leaks onto the floor.
Washer repair in Parker, photo from our job records
Washer repair in Parker

Can mold and bacteria from a washer reach people?

The EPA says molds produce allergens and irritants, can cause allergy symptoms such as sneezing, runny nose, red eyes and skin rash in sensitive people, and can trigger asthma attacks in people with asthma who are allergic to mold.

In a well-known case at University Hospital Bonn in Germany, drug-resistant Klebsiella oxytoca bacteria found in a washing machine’s rubber door seal and detergent drawer was passed to newborns through clothing washed in it; it stopped when the machine was taken out of use. The researchers noted that low-temperature, energy-saving washing is less likely to kill germs. Most households don’t need to worry about that level of risk, but it shows that what grows in the seal can travel on laundry.

✓

What a clean gasket gets you

  • Laundry that smells clean.
  • No black specks on towels and clothes.
  • A boot that lasts and doesn’t leak.

Warning signs

  • Black or gray spots in the gasket folds.
  • Musty smell from the drum or from clean laundry.
  • Slime, hair or coins in the bottom of the boot.
  • Tears, holes or hardened rubber.
  • Water leaking at the front of the washer.

How to clean a washer door gasket

  1. Pull the gasket back and remove hair, lint, coins and debris from the folds.
  2. Wipe the folds with warm soapy water. For mold, use a diluted bleach solution or an oxygen bleach cleaner, following your manual. Wear gloves and keep the room ventilated, and never mix bleach with other cleaners.
  3. Let it sit a few minutes, scrub gently with a soft brush and wipe clean.
  4. Dry the gasket completely with a towel.
  5. Run the Tub Clean or Self Clean cycle.
  6. From now on, wipe the gasket weekly, remove laundry promptly and leave the door and detergent drawer open after each wash.

Brand notes

Brand What to know
LG LG recommends wiping the gasket with oxygen bleach, leaving the door open and running Tub Clean monthly. If odor continues after several tub cleans, the washer needs service.
Samsung Samsung recommends wiping the door, gasket and detergent area weekly and drying the folds completely.
Whirlpool / Maytag / Kenmore Front-loaders call the gasket a “bellow” or “door boot”. Clean Washer cycles with a washer cleaner help, but stained or torn bellows need replacement.
GE Some models have a gasket-drying fan (UltraFresh vent); keep it clear and still wipe the folds.
Miele / Bosch Run a hot maintenance wash regularly if you wash mostly at low temperatures.

Denver area notes

Many Denver-area laundry rooms are in basements and closets with little ventilation, so the drum and gasket stay damp longer. Leave the door open and, if possible, run a fan or dehumidifier in the laundry area.

Photos from our service calls

Washer repair in Superior, photo from our job records
Washer repair in Superior
Washer repair in Niwot, photo from our job records
Washer repair in Niwot
A GE front-load washer in Lafayette with the old door gasket removed, ready for a new one
A GE front-load washer in Lafayette with the old door gasket removed, ready for a new one.
Washer repair in Boulder, photo from our job records
Washer repair in Boulder
Washer repair in Westminster, photo from our job records
Washer repair in Westminster
Washer repair in Lakewood, photo from our job records
Washer repair in Lakewood
Washer repair in Berthoud, photo from our job records
Washer repair in Berthoud

When to call a technician

  • Black spots stay in the rubber after a bleach cleaning.
  • The gasket is torn, cracked or hard.
  • Odor continues after several tub cleans.
  • Water leaks at the front of the washer.

FAQ

Can I just clean a moldy washer gasket?

Yes, if the mold wipes off and the rubber is intact. If black stains stay in the rubber after cleaning or the gasket is torn, replace it.

Can washer mold get on my clothes?

Clothes rub against the gasket and rinse water passes over it every cycle. Musty-smelling or speckled laundry is a common sign.

How do I stop the mold from coming back?

Wipe and dry the gasket weekly, leave the door open after washing, use the right amount of HE detergent and run a tub clean every month.

How long does a door boot last?

It depends on use and care. Torn or permanently stained boots should be replaced.

Want a technician to do it? Call 720-230-1229. We serve Denver, Boulder County and 52 surrounding cities.

720-230-1229
720-230-1229
Call Now Book Online