Frigidaire Oven & Range Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

On Frigidaire ranges, F1x codes point to the oven control or touch panel (F10 runaway heat, F11 stuck key, F13 memory), F2x codes to communication between boards, F30 and F31 to the oven temperature sensor, and F90 to F97 to the motorized door lock. Reset the breaker for 30 seconds; if the code returns, the range needs a technician. Treat F10 as a safety issue and do not use the oven.

Frigidaire (Electrolux) ranges and wall ovens show F codes grouped by system: F1x for the control, F2x for board communication, F3x for sensors and probes, and F9x for the door lock. Older Frigidaire controls used single-digit codes such as F1, F3 and F9, and some newer models show 4-digit or split codes. This list combines Frigidaire's support pages with codes documented by Sears PartsDirect and repair references.

Frigidaire Oven & Range error codes and what they mean

Code What it means What to try
F10 Runaway temperature: the oven is above about 600°F and still rising, or heating with no cook cycle set. Often a failed temperature sensor or a stuck relay on the control.
Call a technician
Turn the oven off at the breaker and let it cool. Do not use it until it is checked; a sensor, relay or control fault can cause runaway heat.
F11 Stuck or shorted key: a key on the touch panel has been held for 30 seconds or more.
Call a technician
Make sure nothing presses on the panel, wipe it dry and press Stop/Cancel. Reset power. If F11 returns, the touch panel or control needs replacing.
F12 Control microprocessor identification fault (some gas models: key code does not match the key map).
Call a technician
Turn the power off at the breaker for 30 seconds to a minute, then back on. If the code returns, request service.
F13 Control memory (EEPROM) failure or checksum error.
Call a technician
Turn the power off at the breaker for 30 seconds to a minute, then back on. If the code returns, request service.
F14 Depending on model: communication error between the oven control and the glass touch panel (or touch panel disconnected), or an oven control board failure.
Call a technician
Turn the power off at the breaker for 30 seconds to a minute, then back on. If the code returns, request service.
F15 Control self-check failed or keyboard error.
Call a technician
Turn the power off at the breaker for 30 seconds to a minute, then back on. If the code returns, request service.
F16 / F17 / F18 / F19 Control faults on some models: user interface cannot read the burner knobs (F16) or configure the touch panel (F17), relay board failure (F18), or user interface cannot configure the relay board (F19).
Call a technician
Turn the power off at the breaker for 30 seconds to a minute, then back on. If the code returns, request service.
F3 / F20 / F26 Communication error between the oven control and the user interface or surface (cooktop) controls.
Call a technician
Turn the power off at the breaker for 30 seconds to a minute, then back on. If the code returns, request service.
F22 / F23 / F24 / F25 / F27 / F28 / F29 Communication failures between control boards on some models (user interface, relay board, glass touch panel, or convection fan speed board on F23/F24).
Call a technician
Turn the power off at the breaker for 30 seconds to a minute, then back on. If the code returns, request service.
F30 Open oven temperature sensor (RTD) or wiring. The oven may show F10 first.
Call a technician
Reset power at the breaker once. If the code comes back, a technician should test the sensor (about 1,100 ohms at room temperature on most models) and its wiring.
F31 Shorted oven temperature sensor (RTD) or wiring.
Call a technician
Reset power at the breaker once. If the code comes back, a technician should test the sensor (about 1,100 ohms at room temperature on most models) and its wiring.
F33 Meat probe sensor shorted or reading too hot (above about 392°F). Unplug the meat probe, check it for damage and try cooking without it. If the code stays, request service.
F40 / F41 Cooktop lockout fault.
Call a technician
Turn the power off at the breaker for 30 seconds to a minute, then back on. If the code returns, request service.
F50 Relay board cannot read the door switch or motorized door lock switch status.
Call a technician
Let the oven cool completely, then reset power at the breaker for 30 seconds and try again. Do not force the door. If the code returns or the door stays locked, request service.
F60 Commonly reported on some slide-in models as the control board overheating, usually because the cooling fan is not running.
Call a technician
Keep vents clear and let the range cool. Reset power. If it returns, a technician should check the cooling fan.
F62 Missing zero-cross (power timing) signal at the control.
Call a technician
Turn the power off at the breaker for 30 seconds to a minute, then back on. If the code returns, request service.
F90 Door lock motor failure: the control does not see the lock motor running, or unlocking took too long.
Call a technician
Let the oven cool completely, then reset power at the breaker for 30 seconds and try again. Do not force the door. If the code returns or the door stays locked, request service.
F91 Too many door unlock attempts.
Call a technician
Let the oven cool completely, then reset power at the breaker for 30 seconds and try again. Do not force the door. If the code returns or the door stays locked, request service.
F92 Door was open too long during a lock cycle.
Call a technician
Let the oven cool completely, then reset power at the breaker for 30 seconds and try again. Do not force the door. If the code returns or the door stays locked, request service.
F93 Door lock took too long.
Call a technician
Let the oven cool completely, then reset power at the breaker for 30 seconds and try again. Do not force the door. If the code returns or the door stays locked, request service.
F94 Too many door lock attempts.
Call a technician
Let the oven cool completely, then reset power at the breaker for 30 seconds and try again. Do not force the door. If the code returns or the door stays locked, request service.
F95 Door lock motor does not stop running, or the lock switch sends an invalid signal.
Call a technician
Let the oven cool completely, then reset power at the breaker for 30 seconds and try again. Do not force the door. If the code returns or the door stays locked, request service.
F96 Oven door detected open during a self-clean cycle.
Call a technician
Let the oven cool completely, then reset power at the breaker for 30 seconds and try again. Do not force the door. If the code returns or the door stays locked, request service.
F97 Motorized door lock in an unexpected state.
Call a technician
Let the oven cool completely, then reset power at the breaker for 30 seconds and try again. Do not force the door. If the code returns or the door stays locked, request service.
F01 / F02 / F04 / F05 Some gas and glass-touch models: touch panel failure.
Call a technician
Turn the power off at the breaker for 30 seconds to a minute, then back on. If the code returns, request service.
F03 Some models: oven user interface board configured incorrectly or failed.
Call a technician
Turn the power off at the breaker for 30 seconds to a minute, then back on. If the code returns, request service.
F0 13 / F0 15 / F5 00 / F7 01 / F7 02 / F7 10 Some glass-touch models: user interface board failure (F0 13, F0 15) or communication failure between the user interface, oven control and glass touch panel.
Call a technician
Turn the power off at the breaker for 30 seconds to a minute, then back on. If the code returns, request service.
F7 12 / F7 20 Commonly reported on models with knobs: a burner control knob sensor (potentiometer) problem, or the user interface board or its harness.
Call a technician
Turn the power off at the breaker for 30 seconds to a minute, then back on. If the code returns, request service.
F1 (older models) Depending on model: shorted keypad (Frigidaire's meaning on newer controls), or runaway temperature / oven sensor or control failure on older electronic controls.
Call a technician
Reset power once. If the oven overheated, do not use it until checked. If F1 returns, request service.
F3 / F4 (older models) Older controls: oven temperature sensor open (F3) or shorted (F4).
Call a technician
Reset power at the breaker once. If the code comes back, a technician should test the sensor (about 1,100 ohms at room temperature on most models) and its wiring.
F8 / F9 (older models) Older controls: door lock motor or lock switches out of position.
Call a technician
Let the oven cool completely, then reset power at the breaker for 30 seconds and try again. Do not force the door. If the code returns or the door stays locked, request service.
nCAL / LinE ERR Oven control board failure on some models.
Call a technician
Turn the power off at the breaker for 30 seconds to a minute, then back on. If the code returns, request service.
- (dash) or Loc Oven or cooktop controls are locked. Not a fault. Press and hold Off (Cancel) for about 6 seconds to unlock.

What we actually find on Frigidaire ovens in the Denver area

The codes above come from Frigidaire’s own documentation. This section shows what our technicians found once they opened the machine. Since 2024 we have handled 18 Frigidaire oven service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The oven repairs we do most often (all brands)

Our notes on Frigidaire ovens are too thin to rank by brand alone, so here is what we found across all 645 oven calls in our records:

  1. Control board: 54 calls
  2. Igniter: 45 calls
  3. Bake or broil element: 26 calls
  4. Surface element or burner switch: 20 calls
  5. Wiring: 16 calls
  6. Convection fan: 15 calls
  7. Temperature sensor: 13 calls

Oven repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2024–2026. Customer details removed.

Video: Frigidaire oven error codes

Video by Parts Dr

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • Across all 645 oven calls in our records (all brands), the repairs we do most often: control board (54 calls), igniter (45) and bake or broil element (26).

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. Turn the range off at the breaker for 30 seconds to a minute, then back on.
  2. Wipe the touch panel dry and make sure nothing presses on it (F11).
  3. Unplug the meat probe for probe codes (F33).
  4. Let the oven cool fully before trying self-clean again or touching a locked door (F90 to F97).
  5. If you see F10, leave the breaker off until the oven is checked.
  6. For gas ranges, never adjust gas connections yourself.

When to call a technician

  • Any F code returns after a breaker reset.
  • F10 appears, or the oven keeps heating when turned off.
  • The door stays locked after the oven has cooled.
  • The oven will not heat, or you smell gas or burning.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

How do I clear an F code on my Frigidaire oven?

Turn the range off at the circuit breaker for 30 seconds to a minute, then turn it back on. If the code returns, the range needs service. If the unit was installed within the last 30 days, contact the installer first.

What does F10 mean on a Frigidaire oven?

F10 means runaway temperature: the control sensed the oven above about 600°F and rising, or heating with no cycle set. A failed temperature sensor or a stuck control relay is the usual cause. Do not use the oven until it is checked.

What does F11 mean on a Frigidaire range?

F11 means a key on the touch panel has been read as pressed for 30 seconds or more. Dry the panel and reset power; if it returns, the touch panel or control needs replacing.

What do F90 to F97 mean?

These are motorized door lock faults, such as the lock motor not running, taking too long, or too many lock attempts. Let the oven cool, reset power and do not force the door.

What does F30 or F31 mean?

F30 means the oven temperature sensor circuit is open and F31 means it is shorted. The sensor or its wiring usually needs replacing.

Sources: support.frigidaire.ca, owner.frigidaire.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, nelihome.com, blog.askgene.com, appliancepartspros.com. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229
Call Now Book Online