JennAir Refrigerator Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

A JennAir refrigerator talks to you in two ways. Alarms such as PO, Over Temp and Temperature Alarm are warnings about warm food, and you clear them yourself. A flashing F followed by an F#E# number is a fault the control found in a part. The number after F tells you the system: 3 is a sensor, 4 a heater, 6 the boards, 7 the sealed system, 8 the ice maker, 9 the lights and A a fan or damper.

JennAir built-in, column and freestanding refrigerators are made on a Whirlpool platform, but JennAir only publishes the alarms and the general rule for a flashing F. The F#E# meanings in our tables come from Whirlpool-platform service literature, so treat them as a strong hint rather than a final diagnosis. Column models use their own shorter alarm list. On a built-in, a returning code deserves quick attention: panel-ready cabinets make every repair slower, and food losses add up fast in a 42- or 48-inch unit.

JennAir refrigerator codes, sorted by what they point to

Warnings you can clear yourself

Display What the control is telling you First step
PO The power went out and the freezer climbed to about 18 °F (-8 °C) or warmer before it came back. A red outage icon may light, and the rest of the panel is locked until you confirm. Touch Measured Fill under the blinking Confirm. Then go through the freezer and throw out anything that thawed.
Over Temp light On built-in and column units: fresh food above 48 °F (9 °C) or freezer above 15 °F (-9 °C) for longer than 90 minutes. A newly installed unit shows it every 90 minutes until it reaches temperature. Press Over Temperature Reset. If it keeps blinking, kill the breaker for five minutes. No recovery within a day means service.
Temperature Alarm Same 48 °F / 15 °F limits, same 90-minute window, on freestanding models. Blinks until someone acknowledges it. Press Alarm. Look for a door left ajar, vents blocked by food, or a dusty grille.
Door Alarm A door or drawer has stayed open for a few minutes. Shut everything and make sure a bin or bottle is not holding a door off its gasket.
Controls dead, lights on Showroom mode (no cooling, lights only) or Sabbath mode (no lights, chimes, alarms or dispenser). Exit the mode as your manual shows. If the panel still ignores you, cut power for 5 to 10 minutes.
H2O / Replace Filter Filter reminder only. Change the filter and reset the reminder.

F3: temperature and humidity sensors

Code What the control is telling you First step
F3E0, F3E1, F3E2 A thermistor reads open or shorted: fresh-food or main sensor (E0, E1), freezer sensor (E2). Cooling often drops into a timed backup mode.
Technician
One power reset. Put a thermometer in each section while you wait for service.
F3E3, F3E4, F3E5, F3EB A drawer or zone sensor: convertible or pantry drawer (E3, EB), deli drawer (E4), crisper or evaporator defrost sensor depending on model (E5). Reset once; a repeat is a sensor or harness repair.
F3E8, F3E9 Room humidity sensor (E8) or room temperature sensor (E9). The control uses them to run the anti-sweat heaters. Cooling usually continues. Expect condensation around the doors until it is fixed.
F3EC, F3ED, F3EF Sensor in the French-door flipper mullion (EC), the in-door ice box (ED) or a second freezer evaporator (EF). Reset once, then book service if it comes back.

F4: defrost and anti-sweat heaters

Code What the control is telling you First step
F4E1, F4E2, F4E3 Defrost heater circuit for the freezer or main evaporator (E1), the fresh-food evaporator (E2) or the convertible section (E3). Frost slowly chokes the airflow.
Technician
Check the back wall of the freezer for a white frost sheet. The heater, terminator and control all need testing.
F4E8, F4E9, F4ED, F4EE Mullion heater (E8), dispenser wall heater (E9) or a damper heater (ED, EE). Watch for sweat or ice around that spot and book a visit if the code repeats.

F6, F7, F8 and FA: boards, sealed system, ice and airflow

Code What the control is telling you First step
F6E1, F6E2 The main board lost contact with the display (E1) or an expansion board (E2). Usually a connector or harness. Reset once before calling.
F7E1 The sealed system is not performing: compressor, inverter or refrigerant charge.
Technician
Book service right away and move perishables. Refrigerant work requires a certified tech.
F8E1, F8E2, F8E3, F8E8, F8EC Ice system: ice box sensor (E1), fresh-food ice maker tray sensor or harvest fault (E2, E3), freezer ice maker tray sensor or harvest fault (E8, EC). Switch the ice maker off and on and clear any jammed cubes. Repeats need the ice maker or sensor checked.
FAE1, FAEB, FAEC Freezer evaporator fan (FAE1) or the fresh-food or pantry damper (FAEB, FAEC). Make sure frost or a package is not stopping the fan blade or blocking the damper.

Lights and technician test displays

Display What the control is telling you First step
F9E1, F9E3, F9E4 LED lighting: fresh-food ceiling (E1), freezer (E3) or fresh-food side walls (E4). Food stays cold. Schedule the repair when it suits you.
OP, SH, -88, PA, PE Service test readouts: open thermistor (OP), shorted thermistor (SH), segment test (-88), test passed (PA), programming (PE). Seen only in test mode. OP or SH in normal use: five-minute reset, then service.
CC, OC, F, H, Hi, Lo, EE Temperature-controlled drawer: thermistor shorted (CC) or open (OC), drawer fan (F) or heater (H) not detected, fan speed high (Hi) or low (Lo), lost display link (EE). Five-minute reset. Service if the drawer will not hold its setting.

What we find on JennAir refrigerators and similar refrigerators in the Denver area

We see fewer JennAir refrigerators than the big-volume brands: 2 service calls in our records since 2023. The parts that fail are much the same across brands, so here is what we found on all 1685 refrigerator calls in our records since 2023.

The refrigerator repairs we do most often (all brands)

  1. Compressor or sealed system: 167 calls
  2. Evaporator or condenser fan: 121 calls
  3. Control or inverter board: 120 calls
  4. Ice maker: 109 calls
  5. Defrost system: 66 calls
  6. Thermistor or sensor: 37 calls
  7. Water inlet valve: 32 calls

Recent refrigerator calls

Refrigerator repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: JennAir refrigerator error codes

Video by PeachBandit

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • Across all 1685 refrigerator calls in our records (all brands), the repairs we do most often: compressor or sealed system (167 calls), evaporator or condenser fan (121) and control or inverter board (120).

Don’t want to do it yourself? Call 720-230-1229.

How we handle a JennAir code on a service call

  1. We read the full F#E# code and pull the tech sheet for your exact model before ordering anything.
  2. We check temperatures in every compartment, because a sensor code with normal temperatures is a different repair than one with warm food.
  3. For F4 codes we look at the evaporator for frost first; for F8 codes we check the water supply and the ice maker harness.
  4. On built-ins we plan around the cabinet panels so the unit can be pulled out or serviced in place without damage.

Book a visit when

  • A flashing F returns within a day of a breaker reset.
  • Over Temp keeps coming back even though the doors stay shut.
  • The freezer back wall is coated in frost or the fridge section is warming.
  • F7E1 shows, or the compressor hums but nothing gets cold.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

JennAir refrigerator code FAQ

How do I reset a JennAir refrigerator?

Switch off the breaker or unplug the unit. One minute is enough for freestanding models; give built-ins five minutes. Restore power, confirm cooling is on, and watch the display for a minute.

What does PO mean on a JennAir?

It means there was a power outage long enough for the freezer to reach about 18 °F. Confirm it on the panel and check the frozen food.

Why does Over Temp keep flashing on my new JennAir built-in?

A new unit takes many hours to pull down to temperature, and the light repeats every 90 minutes until it does. If it still flashes after a full day, have it checked.

Can I keep using the fridge with an F3 sensor code?

Usually yes for a short time, since the control falls back to timed cooling. Keep thermometers inside and get the sensor replaced soon.

Sources: producthelp.jennair.com, producthelp.jennair.com, producthelp.jennair.com, producthelp.jennair.com, producthelp.jennair.com, producthelp.jennair.com, producthelp.jennair.com, producthelp.whirlpool.com, producthelp.kitchenaid.com, mypros.plus, mypros.plus, mypros.plus. Codes and meanings can vary by model; check your owner’s manual.

720-230-1229
720-230-1229
Call Now Book Online