Maytag Washer Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

Five problems produce most Maytag washer codes: water coming in too slowly (F8E1, LF, Lo FL), water leaving too slowly (F9E1, drn), a lock that will not engage (F5E2, LdL), an off-balance or oversized load (OFb, F0E5, OL) and excess suds (Sd, Sud). Opening the faucets, clearing the drain path, redistributing clothes and cutting back on HE detergent fixes many of them. Codes starting F1, F3, F6 or F7 involve the boards, sensors or drive and need a technician.

Today’s Maytag Bravos, Centennial and Maxima washers use Whirlpool’s control platform, so most F#E# codes overlap with Whirlpool’s. A handful differ between front-loaders and top-loaders, and the older Neptune front-loaders have their own short codes, listed separately at the bottom. Bravos top-loaders without a display signal faults with lights instead. Unplug the washer and close both supply valves before you inspect anything. Codes labelled “commonly reported” or “some models” come from parts references rather than Maytag directly.

Maytag washer codes, organised by symptom

Filling and water supply

Code What the washer is reporting How to respond
F8E1, LF, Lo FL The tub filled too slowly or the flow is low. On Maxima front-loaders F8E1 can mean no water was sensed at all. Both faucets fully open, both hoses connected and unkinked. With the water and power off, rinse the small screens where the hoses attach.
F8E4 Maxima front-loaders: the flow meter timed a long fill. Same checks as F8E1. Persistent? Book a visit.
HC, F8E5 Hot and cold hoses are connected to the wrong inlets. Shut the water, swap the hoses, run again.
F8E3, F8E6 Overflow (F8E3). Top-loaders: water sat in the tub with the lid up for over 10 minutes (F8E6).
Technician
Close the supply valves. For F8E6 close the lid and restart. Water entering with the washer off means a failed inlet valve.
F8E0 Maxima steam models: steam valve failure.
Technician
Five minutes unplugged, one restart; a repeat needs diagnosis.
F4E0 Maxima front-loaders: internal water heater failed.
Technician
Five minutes unplugged, one restart; a repeat needs diagnosis.

Draining and suds

Code What the washer is reporting How to respond
F9E1, F9E2, drn, dr Draining is too slow, usually more than about 8 minutes on front-loaders. Unkink the drain hose; the standpipe should be 39 to 96 inches tall. On a front-loader, unplug it and empty the pump filter behind the lower panel.
Sd, Sud, SUDS, F0E2 Suds overload. The washer adds rinses to work through it. Let it finish. Measure HE detergent, and switch from splash-less bleach to regular liquid bleach.
F8E2 Dispenser-system front-loaders: dispenser fault. Soak out caked detergent from the drawer or bulk cartridge.

Lid, door and lock

Code What the washer is reporting How to respond
F5E2, LdL Door (front-load) or lid (top-load) will not lock. Clear anything in the opening and wipe soap residue off the latch. Front-loaders: Pause/Cancel twice, then Power.
LdU, F5E3 Lock will not release. On a top-loader LdU usually means weight on the lid. Lift off the laundry basket. Still locked with nothing on top? Service.
lid Top-loaders: lid left up; after 10 minutes the cycle resets and drains. Close it and restart without adding more detergent.
F5E1, F5E4 Lid or door switch fault (E1); the lid or door was not opened between two cycles (E4). For E4, open and close, then start. E1 that returns means the switch assembly.

Load size and balance

Code What the washer is reporting How to respond
OFb, F0E5 The load is off balance; the washer tries to correct it on its own. If it stops, redistribute. Avoid a single heavy item. Use Bulky/Sheets with Deep Water Wash for waterproof items, and level the cabinet.
OL, F0E3 Top-loaders: too much laundry; water and detergent are drained. Take out a few pieces, add detergent, close the lid, press Start.
rL, F0E1, F34 Clothes found in the drum during Clean Washer. Empty the drum and rerun Clean Washer.

Motor, sensors and controls

Code What the washer is reporting How to respond
F7E1 Motor or basket speed sensing error; on some top-loaders, power lost during spin.
Technician
New front-loader? Confirm the shipping bolts are out. Do not overload.
F7E2 to F7E9 Drive faults: motor failure or overheating, clutch or shifter, motor not up to speed, locked rotor.
Technician
One smaller test load after a five-minute unplug.
F3E1 Water level pressure sensor.
Technician
Five minutes unplugged, one restart; a repeat needs diagnosis.
F3E2, F0E4 Water temperature sensor (F3E2). Top-loaders: rinse water too hot, so spin was limited (F0E4).
Technician
Make sure the hoses are on the correct inlets.
F1E1, F1E2, F1E3 Main board failure (E1), motor control error (E2), board mismatch (E3).
Technician
Five minutes unplugged, one restart; a repeat needs diagnosis.
F2E1 Stuck button. Press each one firmly; a key that stays stuck means a new interface.
F6E1, F6E2, F6E3, F2E3 Boards not communicating, or mismatched.
Technician
Usually wiring or a board.
PF, Int, LOC Power cut mid-cycle (PF), cycle paused or cancelled on a front-loader (Int), control lock on (LOC or LC). PF: hold Start. Int: let it drain, Pause/Cancel twice, Power once. LOC: hold Control Lock.
Bravos lights (no display) Flashing Lid Lock: a code is stored. Wash light on: slow or no fill. Spin light on: slow drain. Check water supply or drain hose accordingly; a tech reads the stored code in diagnostic mode.

Older Neptune front-loaders

Code What the washer is reporting How to respond
nF Filled for 12+ minutes without reaching level. Open valves, check hoses. Unplug if water will not stop.
nd Water still in the drum when spin started. Check the drain hose and pump area.
dc Unbalanced load. Redistribute or add similar items.
FL, LO Door failed to lock (FL) or unlock (LO).
Technician
Close the door firmly and restart.
od, dO Door not opened after two full cycles (od), or door open (dO). Open and close the door, start again.
OE Overflow.
Technician
Close the valves, unplug, call.
LE, Lr, E2 Level sensor (LE), locked rotor (Lr, commonly reported), stuck key (E2).
Technician
Five minutes unplugged, one restart; a repeat needs diagnosis.

What we actually find on Maytag washers in the Denver area

The codes above come from Maytag’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 85 Maytag washer service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

Code Our calls What we found
F6E2 1 Control or display board.

The Maytag washer repairs we do most often

Across all 85 Maytag washer calls, with or without a code on the display:

  1. Control or display board: 8 calls
  2. Shock absorbers or suspension: 3 calls
  3. Door or lid lock: 3 calls
  4. Drain pump: 2 calls
  5. Drive belt or coupler: 2 calls

Recent Maytag washer calls

  • Longmont (80503), October 2026: Maytag washer not draining. Repair: drain pump replaced.
  • Erie (80516), September 2026: Maytag washer leaking. Repair: control or display board replaced.
  • Boulder (80301), July 2026: Maytag washer leaking. Repair: shock absorbers or suspension replaced.
  • Superior (80027), April 2026: Maytag washer not spinning. Repair: door or lid lock replaced.

Maytag washer repairs from $190. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Maytag washer error codes

Video by Parts Dr

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • The Maytag washer repairs we do most often across the Denver metro and Boulder County: control or display board (8 calls), shock absorbers or suspension (3) and door or lid lock (3).
  • Recent call: Longmont (80503), October 2026: Maytag washer not draining. Repair: drain pump replaced.

Don’t want to do it yourself? Call 720-230-1229.

Try these before you book

  1. Unplug the washer and close both supply valves.
  2. Reopen the valves fully, check hose routing and the inlet screens.
  3. Check the drain hose height and, on a front-loader, the pump filter.
  4. Even out the load and check that all four feet sit firmly on the floor.
  5. Measure HE detergent; Denver-area water does not need extra.

When a Maytag washer needs us

  • An F1, F3, F6 or F7 code returns after the reset.
  • Water stays in the drum with a clean filter and clear hose.
  • Water keeps entering while the washer is off, or there is a leak.
  • The lock will not release, or you hear grinding, banging or smell burning.

Maytag washer codes on our own jobs

In Erie, a Maytag showing LD, the long drain code, needed a main control board. Another Erie Maytag showed E01 F03 and came in for a drain-side check covering the pump, the pressure switch and the board. Before calling about LD, check the drain hose and the pump filter if your model has one; a sock in the pump causes the same code as a failed part.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Maytag washer code FAQ

Do Maytag and Whirlpool washers share error codes?

Current models mostly do, since Whirlpool builds both. Older Neptune front-loaders use their own codes.

How do I reset a Maytag washer?

Unplug it for about five minutes, plug it back in and start one cycle. A returning code means the fault is real.

What does LdL mean?

The lid or door could not lock. Clear anything in the way and clean the latch area before calling for service.

Why does my washer keep showing OFb?

The load is unbalanced. Mix item sizes, avoid washing one heavy piece alone, and make sure the washer is level.

Sources: producthelp.maytag.com, producthelp.maytag.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, removeandreplace.com. Codes and meanings can vary by model; check your owner’s manual.

720-230-1229
720-230-1229

Photos from our job records

Real photos our technicians took on repair calls around Denver and the Front Range. Each caption says where the job was.

Washer repair in Westminster, photo from our job records
Washer repair in Westminster
Washer repair in Lakewood, photo from our job records
Washer repair in Lakewood
Washer repair in Berthoud, photo from our job records
Washer repair in Berthoud
Washer repair in Thornton, photo from our job records
Washer repair in Thornton
Call Now Book Online