Maytag Oven & Range Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

A Maytag range or wall oven shows a fault code when its control sees a reading it does not trust. Newer Maytag controls use a two-part “F#E#” format, where the first number names the system (F3 is the temperature sensor, F5 the door lock, F8 the cooling fan) and the second narrows it down. Older Maytag electronic ranges use short F-codes or two-part numbers such as 3d/11. Any code that says the oven ran too hot means stop using it until it is checked.

Maytag cooking appliances are built by Whirlpool, so the code logic matches Whirlpool-built ranges. The list covers Maytag electric and gas ranges, wall ovens and double ovens. Below, the codes are grouped by the part of the oven they point to, so you can see at a glance whether you are dealing with a sensor, the door lock, the fan or the control itself.

Maytag range and oven codes, grouped by system

Control board and keypad

Code Meaning on Maytag controls Our advice
F1E0, F1E1, F1E2 The main oven board failed one of its own self-checks: memory (EEPROM) data or the internal analog-to-digital reading.
Call a technician
One breaker reset is reasonable. If the code is back within a day, the board usually needs replacing.
F1E3, F1E4 The board and the wiring harness disagree about which oven this is (size or model ID). Common right after a board swap. A tech has to match or re-set the board for your model.
F1E5, F1E6 F1E5: a sensor reading or calibration value is out of range. F1E6: the latch signal does not make sense to the board. Reset once. Repeat codes need testing of the sensor or latch circuit before buying a board.
F1E7, F1E9 The thermistor built onto the board is open or shorted (F1E7), or the board’s software crashed (F1E9). Board-level fault. Not a homeowner repair.
F2E0, F2E1 The touch panel is unplugged, not answering, or has a key that reads as permanently pressed. Wipe the panel dry; steam and spills cause false presses. If it persists, the keypad or its ribbon cable is replaced.
F2E2, F2E5, F2E6 Problem in the Cancel key circuit. Usually a keypad replacement.
F2E3, F2E4 User interface or its harness is faulty. Check that the range was not jostled during cleaning; otherwise service.
F6E0 The display board and the oven control stopped talking to each other. Often a loose connector behind the console.
F6E4, F6E5, F6EA, F8EA The control panel and the oven board are mismatched, not programmed for this model, or the interface wiring is bad. Needs the correct part numbers for your exact model.
FEE8, FBE1, FBE2 A fault the control detected but Maytag’s help pages do not tie to one part. Diagnosis with a meter is the only way forward.
F0, F1, F5, F7, F8 (older electronic models) F0 or F7: a function key stuck or shorted (on some newer controls F0 just means no fault is stored). F1: keypad or control board defective. F5/F8: internal control errors. Reset once; persistent codes mean the keypad or control.
1C/1C, 1C/2C, 1C/3x to 1C/8x Two-part codes on older Maytag displays: stuck key or bad keypad (1C/1C), keypad cable unplugged (1C/2C), control or Cancel-circuit communication faults (other 1C codes). Keypad and control faults; schedule service.

Temperature sensor, overheating and probe

Code Meaning on Maytag controls Our advice
F3E0, F3E1 The oven temperature sensor reads open (F3E0) or shorted (F3E1). On some double ovens F3E1 refers to the lower cavity. The sensor is a common, affordable part. Reset once; if it repeats, have it tested.
F3 / F4 (older models) Temperature sensor open or shorted. Sources disagree on which letter means which. Same sensor test as above.
3d/11 to 3d/51 Older two-part display: temperature sensor circuit fault. Sensor or wiring check.
F2 (older), F3E2, F6E1, 1d/11, 1d/12 The oven got hotter than it should while baking or broiling, roughly 575 to 600 °F. Some controls use F3E2 for a warming drawer sensor instead. Safety code. Switch the breaker off and let it cool. A stuck relay or failed sensor can keep heating. Do not cook until it is checked.
F3E3, F6E2, 1d/21, 1d/22 Over-temperature during self-clean (above about 950 °F on some models). On certain wall ovens F3E3 is a meat probe fault instead. Stop self-clean and cut power. Have the lock, sensor and relays inspected.
F6E3 Too hot in the warming drawer or lower oven. Same precaution as other over-temperature codes.
F3E4, F4E1 The meat probe or the probe jack is shorted. Unplug the probe and restart. If the code clears, replace the probe.

Door switch and door lock

Code Meaning on Maytag controls Our advice
F5E0, F5E2 The door switch and the lock switch report different states, usually around a self-clean cycle. Make sure nothing blocks the latch, cut power for a minute, try again.
F5E1 The lock motor will not lock or unlock the door. Lock motor or its switch; a frequent repair after self-clean.
F5E3, F5E4 Same disagreement or lock failure, but on the lower door of a double oven. Lower latch assembly service.
F5E5, F5E7, F7E0, F7E1 Latch assembly, door switch or the common wire between them. Wiring and latch test.
4d/11 to 4d/52, 9d/11 to 9d/62 Older Maytag displays: door switch or door lock faults; 9d/31 and 9d/32 appear during Clean. Door lock assembly service.

Cooling fan, elements and power

Code Meaning on Maytag controls Our advice
F7E5, F8E0, F8E2 The cooling fan or its wiring failed, or the fan is spinning too slowly (F8E0) or too fast (F8E2). Listen for the fan after the oven heats. A silent fan is usually the motor.
FEE6, FEE7 Open or faulty circuit for the bake element (FEE6) or broil element (FEE7). Look for a visible break or blister on the element; replacement is straightforward.
F9, F9E0 Power problem at start-up: the outlet or range wiring is miswired, or a voltage dip occurred. On some models a key pressed during power-up triggers it. If the range was just installed or moved, have the outlet and cord wiring checked first.
C81, C82, C83 The cooktop overheated and its automatic shutoff tripped. Let it cool. Repeated trips point to a limiter or a sensor under the glass.
FC E1 (to FC E9) Connected models only: Wi-Fi setup failed (FC E1) or another connectivity issue. Re-run setup in the app; not a repair issue.

Display messages that are not faults

Display What it means What to do
H Hot-surface warning on the cooktop. Nothing; it clears when the glass cools.
PF, flashing clock, PF id 27 / 30 The range lost power. Set the clock again.
LOC, Lock, Locked Control lock is turned on. Press and hold the lock key (often 3 seconds).
SAb / 5Ab Sabbath mode. Turn Sabbath mode off in settings.
ES, blank clock Energy Save mode or a hidden clock display. Change the display setting.
C, CAL Celsius display (oven will not show above 260) or temperature calibration mode. Switch back to Fahrenheit or exit calibration.

What we actually find on Maytag ovens in the Denver area

The codes above come from Maytag’s own documentation. This section shows what our technicians found once they opened the machine. Since 2024 we have handled 6 Maytag oven service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The oven repairs we do most often (all brands)

Our notes on Maytag ovens are too thin to rank by brand alone, so here is what we found across all 645 oven calls in our records:

  1. Control board: 54 calls
  2. Igniter: 45 calls
  3. Bake or broil element: 26 calls
  4. Surface element or burner switch: 20 calls
  5. Wiring: 16 calls
  6. Convection fan: 15 calls
  7. Temperature sensor: 13 calls

Oven repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2024–2026. Customer details removed.

Video: Maytag oven error codes

Video by Cambo

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • Across all 645 oven calls in our records (all brands), the repairs we do most often: control board (54 calls), igniter (45) and bake or broil element (26).

Don’t want to do it yourself? Call 720-230-1229.

Before you schedule a visit

  1. Write the code down exactly, including the second half after the “E” or slash.
  2. Cut power at the breaker for 60 seconds and restore it. One reset clears a glitch; a returning code is a real fault.
  3. For over-temperature codes, leave the breaker off and do not test the oven again.
  4. If the range was moved or a new outlet installed, mention it. F9-type codes are often wiring.
  5. Find the model number on the frame behind the storage drawer or around the oven door opening.

When it needs a technician

  • Any code tied to heat that keeps coming back or that appeared with a burning smell.
  • A door that stays locked after self-clean.
  • Board, keypad or communication codes that survive a reset.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Maytag oven code FAQ

Are Maytag oven codes the same as Whirlpool codes?

Largely yes, because Whirlpool builds Maytag ranges. The meaning can still vary by control generation, so always check against your model’s tech sheet.

Can I keep using my Maytag oven with an F3E1 code?

The oven cannot regulate temperature without a working sensor, so most models will not bake. The sensor itself is an inexpensive part.

Why does my Maytag lock up after self-clean with F5E1?

The lock motor or its switch failed while moving the latch. It is one of the most common faults after a self-clean cycle.

Is an over-temperature code dangerous?

It can be. A stuck relay may keep the element on. Turn the breaker off and wait for service.

Sources: producthelp.maytag.com, producthelp.maytag.com, partselect.com, appliancepartspros.com, producthelp.whirlpool.com, producthelp.whirlpool.com, whirlpool.com, producthelp.whirlpool.com, searspartsdirect.com. Codes and meanings can vary by model; check your owner’s manual.

720-230-1229
720-230-1229
Call Now Book Online