Speed Queen Washer Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

On home Speed Queen washers, Er dr, Er FL, Er nF and Er PS are water level codes that usually clear after you open both faucets, straighten the fill hoses and clean the inlet screens. On commercial and laundromat machines, E:FL is a fill error, E:dr a drain error, E:dL a door lock error and E:Ub an unbalanced load. Drive board, motor and heater codes need a technician.

Speed Queen washers are common in homes, apartment laundry rooms and laundromats, and the code style depends on the control. Residential top loaders (TC and TR) show codes such as Er FL; front loaders and electronic models show codes such as Er Sd or Ed 22; commercial models show E: codes plus card, coin and programming codes. The list below comes from a Speed Queen TC5 manual, PartSelect's Speed Queen fault code list and repair references. Unplug the washer and turn off the water before hands-on checks.

Speed Queen Washer error codes and what they mean

Code What it means What to try
Er dr / Er FL / Er nF / Er PS Water level problem on residential models: slow fill, no fill, or the water level sensor did not see the expected level. Turn both faucets fully on, straighten the fill hoses, clean the screens in the water mixing valve inlets, then unplug the washer for 15 seconds to clear the code.
E:FL Fill error: the pressure switch did not register a full tub within 30 minutes of a fill. Check that the faucets are on, the hoses are not kinked, and the inlet screens are clean. If it returns, call for service.
E:dr Drain error: drain time exceeded, or water still detected at the end of spin. Check the drain hose for kinks and the standpipe or floor drain for clogs. Remove any items caught in the pump area if your model has an access filter.
E Sd / Er Sd Slow drain. Check the drain hose and house drain for restrictions, and clean the pump filter if your model has one.
E SudS / Er SL Suds lock: too much foam. Use less detergent, and only HE detergent in front loaders. Run a rinse cycle to clear the suds.
E:Ub / Er ub Unbalanced load. Redistribute the load, avoid washing a single heavy item alone, and run the cycle again. Check that the washer is level.
door / CLoSE door / do / E:dO Door open, or the door was opened during a running cycle. Close the door fully. If it is closed and the code stays, the door switch or its wiring needs service.
E:dL Door lock error.
Call a technician
Open and close the door firmly and restart. If it returns, the lock or switches need service.
Er dLL The door will not unlock.
Call a technician
Unplug the washer for three minutes, then try again. If it stays locked, call for service.
E Ld / Er LE Water leak drain error: a leak was detected during the leak detection step.
Call a technician
Look for water under the washer and at the hose connections. Turn off the water and call for service if you find a leak.
E:0d / E:Pr Pressure switch error (E:0d) or pressure switch sequence error (E:Pr).
Call a technician
Check the fill and drain hoses for kinks. If it returns, call for service.
E:HT / E Ht Heater error (models with an internal water heater).
Call a technician
Unplug for 30 seconds and restart. If it returns, call for service.
E:dF Drive failure: motor or tachometer circuit problem.
Call a technician
Disconnect power and restart to reset. If it returns, call for service.
E:SP Internal (SPI) communication error, often an unplugged transformer or wrong motor control wiring.
Call a technician
Call for service.
E dS / E nr / E bS / E Co Drive board faults: unexpected supply voltage (dS), drive board not ready (nr), drive board shorted (bS), or drive board communication error (Co).
Call a technician
Unplug for 30 seconds and restore power. If it returns, call for service.
Ed 22 / Ed 29 Motor overheating (22) or motor not connected (29).
Call a technician
For 22, let the washer cool, make sure the drum turns freely and do not overload. If either returns, call for service.
Ed 45 / Ed 46-50 / Ed 51 / Ed 53 / Ed 54 Drive board output faults: door lock (45), heater, hot or cold valve, detergent or softener (46-50), inrush or voltage doubler (51), door lock select voltage (53), pump (54).
Call a technician
Unplug to clear. If the code returns, the drive board needs service.
E:07 / E:08 Inoperative control (commercial models).
Call a technician
Call for service; the control board needs replacing.
E:00 / E:01 / E:02 / E:05 / E:09 / E:0B / E:0C / E:0F Commercial programming (micro-wand infrared) errors: misaimed wand, wand removed too early, invalid data, or IR turned off. Re-aim the wand at the IR communicator and retry. For E:0F, enable IR on the control first.
EC:xx (EC:00 to EC:56) Commercial card reader errors, such as communication or time-out (EC:00, EC:02, EC:09), wrong machine type data (EC:03, EC:05, EC:06, EC:0A), no reader communication (EC:19), unreadable card (EC:20), security or site code mismatch (EC:21, EC:22), and reader faults (EC:25-EC:30). Retry the card and clean the card contacts. For EC:19, power the machine down and up. Reader faults need service.
EI:xx (EI:00 to EI:0F) Commercial infrared communication errors; EI:07 and EI:08 are clock or memory write errors on the control. Re-aim and retry. If EI:07 or EI:08 persist, the control needs service.
Alrm / OFF / Err (coin models) Alrm: possible break-in at the service door or coin vault. OFF: shutdown after that alarm. Err: coin error or jam. Check the service door and coin vault switches, and clear any jam in the coin drop.
Rightmost decimal point lit Network communication error on networked commercial machines.
Call a technician
Wait up to a minute, then power cycle. If it persists, the network board needs service.

What we actually find on Speed Queen washers in the Denver area

The codes above come from Speed Queen’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 7 Speed Queen washer service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The washer repairs we do most often (all brands)

Our notes on Speed Queen washers are too thin to rank by brand alone, so here is what we found across all 1238 washer calls in our records:

  1. Control or display board: 108 calls
  2. Drain pump: 74 calls
  3. Shock absorbers or suspension: 57 calls
  4. Water inlet valve: 41 calls
  5. Door or lid lock: 28 calls
  6. Door boot seal: 27 calls
  7. Drive belt or coupler: 23 calls

Recent Speed Queen washer calls

  • Denver (80209), May 2026: Speed Queen washer door or lid problem. Repair: door or lid lock replaced.
  • Lafayette (80026), April 2026: Speed Queen washer ice maker not working. Repair: pressure or water-level sensor replaced.

Washer repairs from $240. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Speed Queen washer lid lock

Video by AlansMine

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • Across all 1238 washer calls in our records (all brands), the repairs we do most often: control or display board (108 calls), drain pump (74) and shock absorbers or suspension (57).
  • Recent call: Denver (80209), May 2026: Speed Queen washer door or lid problem. Repair: door or lid lock replaced.

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. Unplug the washer before any hands-on check.
  2. Turn both faucets fully on and straighten the fill hoses.
  3. With the faucets off, clean the screens where the hoses attach to the washer.
  4. Check the drain hose for kinks and make sure the standpipe or floor drain is clear.
  5. Use the right amount of detergent, and HE detergent in front loaders.
  6. Spread the load evenly and make sure the washer is level.
  7. Reset by unplugging for 15 to 30 seconds.

When to call a technician

  • Drive board, motor or Ed codes return after a reset.
  • The door will not unlock after unplugging for three minutes.
  • A leak code appears or water is under the washer.
  • The washer will not drain with a clear hose and drain.
  • A commercial machine shows a control or reader fault that power cycling does not clear.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

What does Er FL mean on a Speed Queen washer?

It is a water level code. Make sure both faucets are fully on, the fill hoses are not kinked and the inlet screens are clean, then unplug the washer for 15 seconds to clear it.

How do I reset a Speed Queen washer?

Unplug the washer for 15 to 30 seconds, then plug it back in. If the code returns, the cause is still there.

What does E:Ub mean on a Speed Queen?

E:Ub means the load is unbalanced. Spread the clothes evenly, avoid single heavy items, and run the cycle again.

Why does a laundromat Speed Queen show EC codes?

EC codes are card reader errors on commercial machines. Retrying the card usually works; if the code mentions the reader, the property owner needs to have it serviced.

Sources: partselect.com, laundrynation.com, washingmachinemanuals.com, kellyshomecenter.com, oliverdyersappliance.com. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229
Call Now Book Online