Most Whirlpool washer codes point to a slow fill (F8E1/LF/Lo FL), a slow drain (F9E1/drn), a door or lid that will not lock (F5E2, dL/LdL), an unbalanced load (F0E5, uL, OFb), or too many suds (Sd/Sud). These you can often fix yourself by opening the water valves, clearing the drain hose and filter, spreading out the load, or using less HE detergent. Motor, sensor and control board codes (F1, F3, F6 and F7 families) usually need a technician.
Whirlpool front-load and top-load washers show F#E# codes, and many also show short text codes like LF, Sd or dL. Some codes mean slightly different things on front-load and top-load models, so check your owner's manual if a code does not match what you see. Older top-loads without a display flash a light instead. Before any hands-on check, unplug the washer and turn off the water valves. This list combines the manufacturer's own documentation with codes reported by established repair-parts references (such as Sears PartsDirect, PartSelect and repair technicians' guides); those are marked "commonly reported" or "on some models".
Whirlpool Washer error codes and what they mean
| Code | What it means | What to try |
|---|---|---|
F8E1 / LF / Lo FL |
Long fill or low water flow: the washer is not getting enough water fast enough. | Open both hot and cold faucets fully; both must be connected. Straighten kinked hoses and remove any anti-flood device in the line. With the water off and the washer unplugged, clean the screens where the hoses attach. On front-loaders, clear the code by pressing Pause/Cancel twice, then Power. |
F9E1 / F9E2 / drn / dr |
Long drain: the washer took too long to drain (typically more than 8 minutes). | Check the drain hose for kinks or clogs and make sure it is not pushed too far into the standpipe. The standpipe should be 39 to 96 inches high. On front-loaders, unplug the washer and clean the drain pump filter. Excess suds can also slow draining. If it still will not drain, the pump may have failed. |
Sd / Sud / F0E2 |
Too many suds. The washer adds rinses to clear them. | Let the cycle finish. Use only HE detergent and measure it. Whirlpool also advises against splash-less or easy-pour chlorine bleach, which can foam. Denver's hard water can tempt people to add extra detergent, which makes this worse. |
F5E2 |
Door (front-load) or lid (top-load) will not lock. | Make sure nothing is caught in the door or under the lid and that it closes fully. Wipe detergent buildup off the lock area. If the lock is broken or the code returns after a reset, the lock assembly needs service. |
dL / LdL |
Top-load models: the lid is not locking. | Remove anything trapped under the lid and clean detergent residue around the lid lock. If it keeps happening, the lid lock likely needs replacement. |
dU / LdU |
Top-load models: the lid cannot unlock, usually because something is sitting on it. | Take laundry baskets or other items off the top of the washer. If the code continues with nothing on the lid, request service. |
F5E1 / F5E3 |
Door or lid switch fault (F5E1) or the door or lid will not unlock (F5E3). Call a technician |
Power off for 5 minutes, then try again. If the door stays locked or the code returns, the lock and switch assembly needs diagnosis. |
F5E4 / dr (some front-loads) |
The washer ran several cycles in a row without the door or lid being opened. | Open and close the door or lid between loads, then start the next cycle. |
F0E5 / F0E9 / uL / OFb / ob |
Unbalanced load. The washer tries to rebalance; if it cannot, it stops or limits spin. | Redistribute the load in loose, even heaps and avoid washing one heavy item alone. Use the Bulky/Sheets cycle for comforters. Make sure the washer sits level. If it happens with normal loads, the suspension may be worn. |
OL / F0E3 |
Top-load models: the load is too large for the cycle. The washer drains water and detergent. | Remove several items, add HE detergent again, close the lid and press Start. |
rL / F0E1 / F34 |
Items were detected in the drum during the Clean Washer cycle. | Empty the drum and restart Clean Washer. |
HC / F8E5 |
Hot and cold inlet hoses are reversed. | Turn off the water, swap the hoses so hot goes to hot and cold to cold, and run another cycle. If the hoses are correct, the inlet temperature sensor may be faulty. |
F8E3 |
Overflow: too much water in the tub on most models. On some newer front-loads, Whirlpool suggests checking that the washer is level. Call a technician |
Turn off the water supply and check that the washer is level. If water keeps entering with the washer off, the inlet valve is stuck open and needs service. |
F8E2 |
Front-load models with a dispenser system: the dispenser is clogged or not working. | Remove and clean the detergent drawer or bulk cartridge to clear hardened detergent. If the code returns, request service. |
F7E1 |
Motor or basket speed sensing error: the drum is not reaching the expected speed. Call a technician |
On a new install, confirm all shipping bolts were removed. Do not overload the drum, and check that nothing is jammed. If the code returns after a reset, the speed sensor, motor or wiring needs diagnosis. |
F7E2 / F7E5 / F7E6 / F7E7 / F7E8 / F7E9 |
Drive system faults: motor failure, motor not reaching speed, motor overheating, locked rotor, or (top-load) a shifter fault. Call a technician |
Power off for 5 minutes and try one more cycle with a smaller load. If any of these return, a technician should test the motor, shifter and control. |
F3E1 |
Water level (pressure) sensor fault. The washer may not fill correctly or may overfill. Call a technician |
Power off for 5 minutes and restart. If it returns, the pressure hose, sensor or control board needs service. |
F3E2 / F0E4 |
Water temperature sensor fault (F3E2). On top-loads, F0E4 means rinse water was too hot, so spin speed was limited. Call a technician |
Check that hot and cold hoses are not swapped. Power off for 5 minutes and restart. If F3E2 returns, the temperature sensor or wiring needs service. |
F1E1 / F1E2 |
Main control board fault (F1E1) or motor control fault (F1E2). Call a technician |
Unplug the washer for 5 minutes, then plug it back in. If the code comes back, request service. |
F2E1 |
A control panel button is stuck. | Turn the washer off and press each button firmly to free it. If a button stays stuck, the control panel needs service. |
F6E1 / F6E2 / F6E3 / F2E3 |
Communication error between control boards, or the boards do not match (F2E3, often after a part replacement). Call a technician |
Unplug for 5 minutes and restart. A repeat usually means a wiring or board problem. |
PF / Int |
PF: power was interrupted during a cycle. Int (front-load): the cycle was paused or canceled; the washer may keep draining for 20 to 30 minutes. | For PF, press and hold Start to resume, or press Power to clear. For Int, let it finish draining, then press Pause/Cancel twice and Power once. |
LOC / LC |
Control lock is on. Not a fault. | Press (or press and hold, on some models) the Control Lock button to unlock the controls. |
Older Duet: F20 / FH, F21, F22 |
Older front-loads (roughly 2018 and earlier): F20 or FH means no or low water; F21 means a drain problem; F22 means the door is not locking. | Treat F20/FH like a fill problem, F21 like a drain problem and F22 like a door lock problem, using the steps above. |
Lid Lock light flashing / Wash light on / Spin light on |
Older top-loads without a display: a flashing Lid Lock light means an error is stored; a lit Wash light means no fill or long fill; a lit Spin light means long drain. | Check the water supply for Wash light faults and the drain hose for Spin light faults. A flashing Lid Lock light needs diagnostic mode to read the exact code, which a technician can do. |
Older Duet: F01 / F14 / F99 |
Older Duet front-loads: main control memory (EEPROM) error (F01, F14), or a user interface or main control board failure (F99). Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
Older Duet: F02 |
Early Duet front-loads: long drain, the washer took more than 8 minutes to drain. | Unplug the washer, clean the drain pump filter, and check the drain hose for kinks or clogs. If it keeps happening, call a technician. |
Older Duet: F03 / F23 |
Older Duet models with an internal heater: heating element failure. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
Older Duet: F05 / F24 |
Older Duet models: water temperature sensor error. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
Older Duet: F06 / F25 |
Older Duet models: drive motor tachometer (speed sensor) error. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
Older Duet: F09 / F27 |
Older Duet models: overflow, the water level stayed too high for too long. Call a technician |
Turn off the water valves and unplug the washer. Call a technician; an inlet valve or pressure sensor is likely at fault. |
Older Duet: F10 / F11 / F15 / F31 / F42 |
Older Duet models: motor control unit faults. F10 means the motor control overheated; F11, F15, F31 and F42 point to a motor control board failure (on some early models F11 is listed as a communication error between the motor control and main control). Call a technician |
Unplug the washer for 5 minutes and avoid overloading. If the code returns, call a technician. |
Older Duet: F13 / F30 |
Older Duet models: dispenser circuit or dispenser system failure. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
Older Duet: F26 |
Older Duet models: door switch error. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
Older Duet: F28 / F70 / F71 |
Older Duet models: communication error between the main control and the motor control (F28), or between the main control and the user interface (F70, F71). Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
Older Duet: F29 / FdU / FdL |
Older Duet models: the door would not unlock (F29, FdU) or would not lock (FdL). Call a technician |
Make sure nothing is caught in the door and press it firmly closed. Unplug for 5 minutes and retry. If it persists, call a technician. |
Older Duet: F32 / F35 |
Older Duet models: water level (pressure) sensor failure. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
Calypso: LF / Ld / FL |
Older Calypso top-loads: long fill over 10 minutes (LF), long drain over 5 minutes (Ld), or a flood condition (FL). | Check that both water valves are open and the hoses are not kinked (LF), and that the drain hose is clear (Ld). For FL, turn off the water and call a technician. |
Calypso: ob / SL / LS |
Older Calypso top-loads: off-balance load (ob), suds lock from too much detergent (SL), or a lid switch error (LS). | Rebalance the load and use less HE detergent. If LS keeps showing with the lid closed, call a technician. |
Calypso: Er / CE / CA / CI / Sr |
Older Calypso top-loads: control faults. Er is a processor reset, CE a communication error, CA and CI motor current limits, and Sr a stuck relay. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
What we actually find on Whirlpool washers in the Denver area
The codes above come from Whirlpool’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 96 Whirlpool washer service calls across the Denver metro and Boulder County. Every number here comes from our own job records.
| Code | Our calls | What we found | Part we used most |
|---|---|---|---|
| F8E1 | 2 | Most often: control or display board. Also seen: pressure or water-level sensor. | W11608056 |
| F9E1 | 2 | Most often: control or display board. | WPW10525361 |
| F1E1 | 2 | Most often: control or display board. Also seen: pressure or water-level sensor. | W11608056 |
| F21 | 2 | Most often: drain pump. | WPW10730972 |
| F3E1 | 1 | Pressure or water-level sensor. | W11608056 |
The Whirlpool washer repairs we do most often
Across all 96 Whirlpool washer calls, with or without a code on the display:
- Control or display board: 9 calls
- Drain pump: 8 calls
- Pressure or water-level sensor: 3 calls
- Clogged filter or foreign object: 2 calls
- Water inlet valve: 2 calls
Recent Whirlpool washer calls
- Lakewood (80227), October 2026: Whirlpool washer showing F8E1 and door or lid problem. Repair: pressure or water-level sensor replaced (W11608056).
- Longmont (80503), May 2026: Whirlpool washer not draining. Diagnosis: drain pump.
- Arvada (80007), April 2026: Whirlpool washer door or lid problem. Repair: control or display board replaced (W11322905).
- Arvada (80002), February 2026: Whirlpool washer leaking. Repair: drain pump replaced (WP3363394).
Whirlpool washer repairs from $200. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.
Source: The Appliance Team service records, 2023–2026. Customer details removed.
Video: Whirlpool washer error codes
Video by Parts Dr
What we see on Denver calls
- An error code points to the system that reported the fault, not always to the part that failed.
- The Whirlpool washer repairs we do most often across the Denver metro and Boulder County: control or display board (9 calls), drain pump (8) and pressure or water-level sensor (3).
- Recent call: Lakewood (80227), October 2026: Whirlpool washer showing F8E1 and door or lid problem. Repair: pressure or water-level sensor replaced (W11608056).
Don’t want to do it yourself? Call 720-230-1229.
What you can safely check yourself
- Unplug the washer and turn off both water valves before any hands-on check.
- Open both valves fully, straighten hoses, and make sure hot and cold are not swapped.
- Check the drain hose for kinks and correct standpipe height; on front-loaders, clean the drain pump filter.
- Make sure nothing is caught in the door or under the lid and wipe detergent off the lock area.
- Spread the load evenly, avoid overloading, and check that the washer is level.
- Use only HE detergent, measured. Too much causes suds and drain codes.
- For other F#E# codes, unplug for 5 minutes, then restart the cycle once.
When to call a technician
- A motor, sensor or control code (F1, F3, F6 or F7 family) comes back after a reset.
- The washer will not drain even with a clear hose and filter.
- Water keeps filling with the washer off, or you see an active leak.
- The door or lid stays locked, or the lock is broken.
- You hear grinding or banging, or smell burning, during the cycle.
How to prevent this
Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:
Frequently asked questions
How do I reset a Whirlpool washer error code?
On front-loaders, press Pause/Cancel twice and then Power once. For any model, you can unplug the washer or switch off the breaker for 5 minutes, then restart. If the cause is still there, the code will return.
What does F8E1 or LF mean on a Whirlpool washer?
The washer is filling too slowly. Make sure both hot and cold faucets are fully open, the hoses are not kinked, and the inlet screens are clean.
Why does my Whirlpool top-load washer show uL or OFb?
The load is out of balance. Spread items evenly around the washplate and avoid washing a single heavy item alone. If it happens with normal loads, the suspension may need service.
My older Whirlpool washer has no display and a light is flashing. What does it mean?
On many older top-loads, a flashing Lid Lock light means an error code is stored. A lit Wash light points to a fill problem and a lit Spin light to a drain problem. A technician can read the exact code in diagnostic mode.
Sources: producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, ifixit.com, appliancepartspros.com, partselect.com, removeandreplace.com. Codes and meanings can vary by model; check your owner's manual.