Washer Repair in Lakewood, CO

Same-day washer repair across Lakewood, including Belmar, Green Mountain, Solterra. All brands, written quote before any work.

Service call from $59, $0 with repair Same-day service 90-day parts & labor warranty
10,000+Repairs Completed
50+Brands Serviced
4.9Star Rating
SameDay Service
Washer repair · Lakewood

We fix top-load, front-load and stacked washers from all major brands in homes and condos throughout Lakewood. Same-day visits are often available, and you get a written quote after diagnosis. Go ahead with the repair and the service call (from $59) is waived; parts and labor are covered for 90 days.

In a Lakewood split-level, the washer usually sits one floor below the kitchen, next to a utility sink and a floor drain that have been there since the 1960s. That setup is forgiving when the washer leaks, but it also means older standpipes, old shutoff valves and supply hoses that may be the original rubber. A good share of the washers we repair in Morse Park, Eiber and Glennon Heights fail because of what is plumbed to them as much as what is inside them.

Washer Problems in Lakewood Homes and Condos

Lakewood's population jumped from about 19,000 in 1960 to more than 92,000 in 1970, and most of the bi-levels and split-levels from that boom put laundry on the lower level. When we pull a washer out in one of these homes, we look at the drain standpipe height, the condition of the supply hoses and whether the valves still turn. A standpipe that is too short can siphon water out mid-cycle, and a partly closed valve causes slow fills and error codes that look like a bad washer.

Belmar is a different job. Many condos and townhomes there have stacked washer-dryer pairs or compact front-loaders in a hall closet. Access is tight, so we bring the right tools to service a unit in place, and we pay close attention to door boots, drain pumps and leveling. A small upper-floor leak can stain the ceiling of the unit below, so we trace it to the source.

Water quality is rarely the main issue. Lakewood's Denver Water supply is soft to moderately hard, and while inlet screens can collect some sediment and scale over the years, the more common front-loader complaint here is odor and buildup from low-temperature washes and too much detergent. We clean the pump filter and door boot and check the inlet screens.

Common washer problems we fix in Lakewood

01

Washer won't drain and leaves standing water

A clogged drain pump filter or a failed pump is the most frequent cause, followed by a kinked drain hose. On front-loaders, socks and coins collect in the pump trap. We clear or replace the pump and check the hose route to the standpipe.

02

It shakes, walks or bangs during spin

Worn suspension rods, broken springs, failed shock absorbers or damaged tub bearings let the drum move too much. Uneven floors in older basements can make it worse. We replace the worn suspension parts, check the bearings and level the machine.

03

Water leaking from the front door

On front-loaders, a torn or dirty door boot is the usual source. We inspect the boot for tears and debris, replace it if needed, and check the door latch and the drain path so water is not backing up.

04

Takes forever to fill

Clogged inlet screens, a weak water inlet valve or partly closed house valves slow the fill. We check water pressure at the machine, clean or replace screens and replace the valve if it is failing.

05

Stops mid-cycle with an error code

Error codes can come from a lid or door lock, a pressure switch, a motor control fault or a drain issue. We read the code, test the part it points to and confirm the real cause before ordering anything.

06

Agitator works, but the tub never spins

A worn lid switch or lid lock, a slipping belt, a failed motor coupling or a bad shift actuator can stop the spin while agitation still works. We test the lid circuit and drive parts and replace the one that has worn out.

Before you call: safe checks

  1. Open the shutoff valves behind the washer all the way; in older Lakewood basements these valves can be stiff, so do not force one that will not turn.
  2. Unplug the washer, then unscrew the inlet hoses and check the small screens inside for sediment.
  3. On a front-loader, lay down towels and open the drain pump filter at the lower front to clear socks, coins and lint.
  4. Run a rinse-and-spin with an empty drum to see whether a noise or error repeats without a load.
  5. Check the GFCI outlet or breaker if the washer will not power on at all.

Recent washer repairs in Lakewood

From our job records: 69 washer repairs completed in Lakewood since January 2024.

What we fix most on washers in Lakewood

We counted 19 washer repair jobs in Lakewood in our job records. This is what those jobs needed and which brands they were, so you can see what is likely wrong with yours before we arrive.

Brands we repaired most: LG (3), GE (3), Whirlpool (2), Speed Queen (2), Electrolux (1).

  • Motor, stator and speed sensor — 2 jobs. Spin and agitation faults on direct-drive washers.
  • Control board and panel — 2 jobs. Dead panels, random stops and water-damaged controls.
  • Door or lid lock — 2 jobs. A failed lock stops the washer from starting or spinning.
  • Drive belt — 1 job. A worn or broken belt means the motor runs but the drum doesn't turn.
  • Drain pump — 1 job. A clogged or failed pump leaves water in the drum and triggers drain codes.
  • Door boot — 1 job. Torn or moldy boots cause leaks and smells on front-loaders.
Washer repair in Lakewood, CO - photo from a real job by The Appliance Team
Washer repair in Lakewood
Washer repair in Lakewood: photo from one of our jobs
Washer repair in Lakewood
Washer repair in Lakewood: photo from one of our jobs
Washer repair in Lakewood
Washer repair in Lakewood: photo from one of our jobs
Washer repair in Lakewood
Washer repair in Lakewood: photo from one of our jobs
Washer repair in Lakewood
Washer repair in Denver, CO - photo from a real job by The Appliance Team
Washer repair in nearby Denver
October 2026ZIP 80227

Whirlpool washer

Replaced the main control board.

Repaired · 90-day warranty
September 2026ZIP 80214

GE washer

Replaced the suspension rods.

Repaired · 90-day warranty
November 2026

washer

Control board replacement

Repaired · 90-day warranty
November 2026

Whirlpool washer

Latch replacement

Repaired · 90-day warranty
October 2026

washer

Diverter belt replace

Repaired · 90-day warranty
October 2026

LG washer

Drainage pump replacement, wash pump replacement

Repaired · 90-day warranty
October 2026

Whirlpool washer

Whirlpool washer main control board replacement

Repaired · 90-day warranty
September 2026

GE washer

GE washer suspension rods replacement

Repaired · 90-day warranty
August 2026

Speed Queen washer

Lid lock cleaning

Repaired · 90-day warranty
July 2026

Electrolux washer

Washer Cooktop reset, connection fixing

Repaired · 90-day warranty

Real jobs from our records. Customer details are never shown.

Pricing · updated October 2026

How much does washer repair cost in Lakewood?

Washer Repair starts at $179*.

Common washer repairs and starting prices
RepairFrom*
Lid lock or door latch$179+
Drain pump$179+
Door boot seal$259+
Drive motor or control board$259+
Bearings or transmission$479+

* Labor only; parts are quoted separately.

See full price list →

Washer brands we repair in Lakewood

We repair washers from Whirlpool, Maytag, GE, Samsung, LG, Kenmore and Frigidaire, along with Bosch and Miele compact front-loaders often found in Belmar condos. We also work on Electrolux and Speed Queen, and Speed Queen's commercial-grade top-loaders turn up in older Lakewood basements where owners want a machine that lasts.

Commercial equipment in Lakewood

We service on-premise laundry equipment for Lakewood businesses, including hotels near Sixth Avenue and Wadsworth and operations around St. Anthony Hospital, as well as shared laundry rooms in apartment buildings.

Commercial laundry repair →

Repair or replace your washer?

Expect a washer to last about 10 to 13 years. Pumps, inlet valves, lid switches, door locks, door boots and suspension parts are almost always worth fixing. Failed tub bearings on a front-loader are the classic tough call, since the job is labor-heavy; on an older budget machine, if the quote passes half the cost of a new washer, we will suggest replacing. In Belmar stacked closets, replacement can be harder than it sounds, because a new pair has to fit the same space and hookups.

Keep it running in Lakewood

  • Swap original rubber supply hoses in 1960s split-levels for braided stainless hoses, and replace them every five years or so.
  • Keep the drain hose only a few inches into the standpipe so it cannot siphon.
  • Use HE detergent sparingly and run a hot cleaning cycle monthly to head off the odor that cool washes cause in front-loaders.
  • Turn the old shutoff valves once a year so they still close if a hose ever bursts.

What Customers Say About Our Washer Repairs

4.9 from 686 reviews · 541 on Google

★★★★★Google review
“Zack is great! He fixed my washer leak a year ago. In the meantime, he also cleaned the back of my fridge from dust. This time it was the dryer. The drum was not spinning. Zack spined the drum by hand and he said is the motor. He made a very quick diagnosis. He took the dryer apart and he found few
— Angelika Molas
★★★★★Google review
“Serhii was fantastic! He was friendly, knowledgeable, efficient, and kept us informed throughout the entire process. He quickly diagnosed the issue with our washer, ordered the necessary parts, and returned just two days later to complete the repair. The service was professional and seamless from
— Eliza Mirabile
★★★★★Google review
“I had an excellent experience getting my washer machine fixed. Denys The technician quickly identified the problem and repaired it efficiently. The service was professional, honest, and reasonably priced.”
— Quyen Doan

Read all reviews on Google →

Washer Repair in Lakewood — FAQs

Yes. We service stacked and compact washers in place in Belmar condos and townhomes. We work around HOA rules for access and check whether the leak or noise is coming from the washer or the plumbing behind it.

In older split-levels, a drain hose pushed too far into the standpipe or a standpipe that is too low can siphon water out. A failing water inlet valve or pressure switch can also cause the washer to refill repeatedly. We check both the washer and the drain setup.

Residue from detergent and fabric softener builds up in the door boot, the drain pump filter and the outer tub. Lakewood's water is not hard enough to be the main cause. We clean the affected parts, replace a damaged boot if needed and suggest settings that keep it fresh.

Yes. Morse Park, Eiber and the 40 West Arts District area have many 1950s-60s homes with lower-level laundry. We repair the washer and point out any worn hoses, valves or drain problems we notice so you can address them.

On a lower level with a floor drain, a pan helps but is not essential. In a Belmar condo or any unit above someone else's ceiling, a pan with a drain line or a leak sensor is a smart addition. We can tell you what fits your laundry space during the visit.

Washer acting up in Lakewood?

Standing water in the drum or a machine that will not spin? Book now and we will bring common washer parts on the first visit.

Lakewood washer calls, from our records

We found 12 washer calls in a sample of our Lakewood records. Drains came up most often: water left in the drum, a front-loader that stopped with a drain code, a top-loader that wouldn’t empty. Many Lakewood ranches have the laundry in the basement, where the drain runs to a standpipe or a laundry sink, and a clogged standpipe can look exactly like a failed pump.

Lakewood washer repairs, in photos

GE front-load washer in Lakewood during repair
GE front-load washer in Lakewood during repair
Washer in Lakewood that was not draining
Washer in Lakewood that was not draining
Washer in Lakewood during diagnosis
Washer in Lakewood during diagnosis

What these calls looked like

Washer What the customer saw What we found or did
GE front-loader Stopped mid-cycle Drain and door lock diagnosis
Whirlpool Not finishing the cycle Diagnosis
Washer Water left in the drum Drain path cleared, pump tested
Washer Not working Diagnosis and repair

Not draining: our order of checks in Lakewood homes

  1. The pump filter on front-loaders, where coins, hair ties and socks collect.
  2. The drain hose behind the washer, which kinks when the machine is pushed back.
  3. The standpipe or laundry sink drain. If it backs up when the washer pumps out, the clog is in the house drain, not the washer, and a plumber is the right call.
  4. The drain pump itself: if it hums but doesn’t move water, it has failed.

This order saves money: many Lakewood “pump failures” are a clogged filter or a house drain.

Basement laundry and older plumbing

Older Lakewood homes often have shutoff valves that haven’t been turned in decades and rubber fill hoses that are cracking. If your valves are stiff, don’t force them; and if your hoses are rubber and more than five years old, replace them with braided hoses. A burst hose in a basement can release a lot of water quickly.

Washer problems by symptom

Won’t spin

The washer needs the lid or door locked, the water gone and the load balanced before it spins. Lid locks, drain problems, worn couplers or clutches on top-loaders and shifters stop the spin.

Leaking

Front-loaders: door boot or detergent drawer. Top-loaders: hoses, pump or tub seal. Too much detergent overflows suds.

Loud

Banging is usually suspension or an unbalanced load; a roar on spin is drum bearings on front-loaders.

Where we work in Lakewood

All of Lakewood: Applewood, Lakewood Heights, Belmar, Union Square, Green Mountain and Bear Creek. Most visits are the same day or the next day.

Washer brands we repair in Lakewood

Whirlpool, Maytag, GE, Samsung, LG, Kenmore, Frigidaire, Electrolux, Bosch, Speed Queen and Amana make up most of the washers we see. Whirlpool and Maytag top-loaders most often need lid locks, couplers, clutches and drain pumps. Samsung top-loaders need suspension rods when they bang. LG and Samsung front-loaders need drain pump cleaning, door locks and door boots. GE washers need lid locks, shifters and pumps. We stock these parts, so most repairs finish on the first visit.

Repair or replace?

Most washers last 10 to 12 years. Pumps, locks, valves, belts, couplers, suspension parts and door boots cost a fraction of a new washer. We suggest replacing when a cracked outer tub, failed transmission or worn-out drum bearings on an older budget machine make the repair poor value, and we say so before any work.

How a washer repair visit works

We run the washer and watch each stage, read any code and run its built-in test cycle, which operates the valves, pump, motor and lock one at a time. Then we test the suspected part with a meter, give you the price and, in most cases, repair it on the spot. We finish with a full cycle including spin and a leak check.

Washer codes we see in Lakewood

Brand and code What it usually means
LG OE Can’t drain: drain filter, hose or pump
LG LE Motor problem, often from an overloaded or unbalanced drum
LG dE Door lock not confirming
LG UE Unbalanced load
Samsung 5C / 5E Can’t drain
Samsung 4C / 4E Not filling fast enough
Samsung UB / UE Unbalanced; worn suspension if it repeats
Whirlpool / Maytag F9 E1 Long drain time
Whirlpool / Maytag F5 E2 Lid lock problem
GE blinking lights Fault code pattern we read in service mode

Codes are a starting point, not a diagnosis. We confirm the part with a test before replacing it.

Top-load or front-load in Lakewood?

Older Lakewood homes mostly have top-loaders, which are simpler and forgiving of hard water and overloading, but use more water. Newer townhomes near Belmar have front-loaders, which clean well and spin drier but need their door boot and drain filter kept clean. Both are worth repairing for most failures.

Whatever your washer is doing, write down the brand, the symptom and any code, and call or book online. We explain what failed in plain language and fix most washers on the first visit.

Before you call: quick checks in Lakewood

  • Are both water taps open and the hoses free of kinks?
  • On a front-loader, is the drain filter at the bottom front clean?
  • Is the lid or door fully closed and the child lock off?
  • Try a smaller, balanced load.
  • Write down any code on the display.

Cost and warranty

The home service visit starts from $59 and repairs start from $150, parts and labor included. You get the exact price before any work, and every repair has a 90-day parts and labor warranty. If the same problem returns within that time, we come back at no charge.

720-230-1229
720-230-1229
Call Now Book Online