The most common Whirlpool dryer codes are AF or F4E3 (restricted airflow from a clogged lint screen or vent), PF (a power interruption), and L2 or F4E4 (low or missing voltage on one leg of a 240-volt supply). You can usually fix AF and PF yourself; L2 often means a tripped breaker. Sensor, heater relay, motor and control board codes (F1, F2, F3, F4E1/F4E2 and F6 families) need a technician.
Newer Whirlpool dryers show F#E# codes, while some older models show codes like F-01 or F:22, or E1 to E3. The same fault can have a different code depending on the model year, so check your owner's manual or the tech sheet inside the console if a code does not match. Unplug the dryer and, on gas models, do not touch the gas line during any check. This list combines the manufacturer's own documentation with codes reported by established repair-parts references (such as Sears PartsDirect, PartSelect and repair technicians' guides); those are marked "commonly reported" or "on some models".
Whirlpool Dryer error codes and what they mean
| Code | What it means | What to try |
|---|---|---|
AF / F4E3 |
Restricted airflow: a clogged lint screen or vent, a crushed or kinked vent, or too many bends. The dryer keeps running but dries slowly and runs hot. | Clean the lint screen. Unplug the dryer and check the vent hose and outside vent hood for lint, kinks or crushing. Touch any key to clear the code. Long or clogged vents are a fire risk, so have the full vent run cleaned if it has been a while. |
PF |
A power failure interrupted the cycle. | Press and hold Start to resume, or press Power to clear. If it happens often, check that the plug is firmly seated and the cord is not damaged. |
L2 / F4E4 |
Electric models: low or no voltage on one leg (L2) of the 240-volt supply, so the heater may not turn on. The dryer still tumbles. | Check for a tripped breaker or blown fuse and reset or replace it. Then run a Timed Dry heated cycle. If the code stays, have a qualified electrician check the outlet and circuit. Do not open the terminal block yourself. |
F1E1 |
Main control board fault. On newer Cabrio-platform models it means a motor relay is stuck on the board; some references also link it to heater relay voltage problems. Call a technician |
Turn off the breaker for 1 to 5 minutes, then run a Timed Dry cycle. If the code returns, the control board or wiring needs diagnosis. |
F1E3 |
The wrong control board is installed, usually after a repair. Call a technician |
This needs the correct replacement part. Request service. |
F2E1 |
A button on the control panel is stuck. | Turn the dryer off and press each button firmly to free it. If a button stays stuck, the user interface needs replacing. |
F2E4 / F2E5 |
Internal software error in the user interface. Call a technician |
Turn off the breaker for a few minutes and restart. If it returns, request service. |
F3E1 |
Exhaust thermistor (temperature sensor) failure. Call a technician |
Turn off the breaker for one minute, then run a Timed Dry cycle and watch for one minute. If the code returns, the thermistor or its wiring needs service. |
F3E2 |
Moisture sensor failure on newer models. Automatic cycles may end too early or run too long. Call a technician |
Wipe the metal sensor strips inside the drum (near the lint screen) with a damp cloth to remove softener residue. If the code returns, the sensor or wiring needs service. |
F3E3 |
Inlet thermistor failure (the sensor at the heat source). Call a technician |
Power off at the breaker for one minute and restart. If it returns, request service. |
F4E1 / F4E2 |
Heater relay failure. The dryer may not heat. Call a technician |
Power off at the breaker for one minute and restart. If it returns, a technician should test the relay, heater circuit and board. On gas models, do not work on the gas valve yourself. |
F6E2 / F6E3 |
Communication lost between the main control board and the user interface. Call a technician |
Power off at the breaker for a few minutes and restart. A repeat usually means a wiring or board problem. |
F-01 / F:01 |
Older Cabrio and Duet models: main control board failure. Call a technician |
Unplug for 5 minutes and plug back in. If the code returns, the board needs replacing. |
F-02 / F:02 |
Older Cabrio and Duet models: keypad failure, usually a stuck button. | Press each button firmly to free it. If it stays stuck, the user interface needs service. |
F-22 / F-23 / F:22 / F:23 |
Older models: exhaust (outlet) thermistor open or shorted. Call a technician |
Check the lint screen and vent first, then request service to test and replace the thermistor. |
F:24 / F:25 |
Older Duet models: inlet thermistor open or shorted. Call a technician |
Request service. The sensor is combined with the high-limit thermostat. |
F-26 |
Older Cabrio models: drive motor failure. Call a technician |
Make sure nothing is jamming the drum. If the drum will not turn, request service. |
F-28 / F-29 / F:28 / F:29 |
Older models: moisture sensor failure. Call a technician |
Clean the moisture sensor strips inside the drum. If the code returns, the sensor or wiring needs service. |
F:30 / F-31 |
Older models: F:30 (Duet) is restricted airflow; F-31 (Cabrio) is low L2 voltage. | For F:30, clean the lint screen and vent. For F-31, check the breaker and have an electrician check the supply if it continues. |
E1 / E2 / E3 |
Some older electronic-control models: E1 and E2 are thermistor failures; E3 means the control panel and board do not match. Call a technician |
Turn off the breaker for one minute and restart. If the code returns, request service. |
F1E4 / F1E5 |
Control unit or control wiring problem, as listed on Whirlpool's support pages. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
F2E2 |
Keypad or control fault. Technicians report that a loose ribbon cable between the keypad and control can cause it. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
F3E4 |
Listed by Whirlpool without a published meaning; commonly treated as a temperature or moisture sensing fault. Control-detected fault; the manufacturer lists the code without a public meaning. Reset by unplugging for 5 minutes; if it returns, call a technician. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
F3E5 |
Models with rear moisture sensors: several loads in a row dried without usable moisture-sensor data. An unlevel dryer or very small loads that do not touch the sensor bars can cause it. | Level the dryer, dry normal-size loads, and wipe the moisture sensor bars with a little rubbing alcohol. If it keeps coming back, call a technician. |
F5E1 |
Commonly reported as a door switch failure: the control cannot confirm whether the door is closed. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
F6E1 |
Communication error between the main control board and the user interface (touchpad), or the wiring between them. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
F7E1 |
Drive motor problem: the motor, its control circuit or wiring. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
F9E2 / FCE1 |
Control-detected fault; the manufacturer lists the code without a public meaning. Reset by unplugging for 5 minutes; if it returns, call a technician. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
0E / 0g / 3E / 6E / -:-- |
Whirlpool lists these on some models with only a power-cycle procedure and no public meaning. Control-detected fault; the manufacturer lists the code without a public meaning. Reset by unplugging for 5 minutes; if it returns, call a technician. Call a technician |
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician. |
ERR |
Not a fault on some models: the door is not fully closed and latched (some models have two latches). | Close the door firmly until it latches, then press Start. |
Loc |
Control Lock is on. Not a fault. | Press and hold the lock key (often 3 seconds) to unlock the controls. |
What we actually find on Whirlpool dryers in the Denver area
The codes above come from Whirlpool’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 79 Whirlpool dryer service calls across the Denver metro and Boulder County. Every number here comes from our own job records.
The Whirlpool dryer repairs we do most often
Across all 79 Whirlpool dryer calls, with or without a code on the display:
- Heating element: 13 calls
- Idler pulley or drum rollers: 5 calls
- Drive belt: 4 calls
- Motor: 3 calls
- Clogged vent or lint: 2 calls
- Thermal fuse or thermostat: 2 calls
- Control board: 2 calls
Recent Whirlpool dryer calls
- Broomfield (80023), October 2026: Whirlpool dryer not heating. Repair: heating element replaced.
- Lafayette (80026), February 2026: Whirlpool dryer ice maker not working. Repair: control board replaced.
- Lakewood (80401), January 2026: Whirlpool dryer making noise. Repair: idler pulley or drum rollers replaced.
- Longmont (80504), December 2025: Whirlpool dryer making noise. Repair: idler pulley or drum rollers replaced.
Whirlpool dryer repairs from $220. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.
Source: The Appliance Team service records, 2023–2026. Customer details removed.
Video: Whirlpool dryer heating element repair
Video by Parts Dr
What we see on Denver calls
- The video shows a heating element repair. It is the most common dryer repair on our calls.
- The Whirlpool dryer repairs we do most often across the Denver metro and Boulder County: heating element (13 calls), idler pulley or drum rollers (5) and drive belt (4).
- Recent call: Broomfield (80023), October 2026: Whirlpool dryer not heating. Repair: heating element replaced.
Don’t want to do it yourself? Call 720-230-1229.
What you can safely check yourself
- Unplug the dryer (or turn off its breakers) before any hands-on check. On gas models, leave the gas line alone.
- Clean the lint screen; wash it with warm soapy water if you use dryer sheets.
- Check the vent hose behind the dryer for kinks or crushing and make sure the outside vent flap opens.
- Check the breaker panel for a tripped breaker if the dryer runs but will not heat.
- Wipe the moisture sensor strips inside the drum with a damp cloth.
- For other F#E# codes, turn off the breaker for one minute, then run a Timed Dry cycle once.
When to call a technician
- A sensor, heater relay, motor or board code keeps returning after a reset.
- The dryer tumbles but never heats, even with breakers on and a clear vent.
- You smell burning or gas, or see scorch marks. Stop using the dryer.
- The drum will not turn or makes grinding or squealing sounds.
- AF keeps coming back after you clean the lint screen and the vent run.
How to prevent this
Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:
Frequently asked questions
How do I clear an error code on a Whirlpool dryer?
Turn off the breaker or unplug the dryer for at least one minute, restore power, and start a Timed Dry cycle. If the code returns within a minute, the fault is still there and needs diagnosis.
What does AF mean on a Whirlpool dryer?
AF means restricted airflow. Clean the lint screen and check the full vent run for lint, kinks or a stuck outside flap. A blocked vent makes the dryer run hot and is a fire hazard.
My Whirlpool dryer shows L2 and will not heat. What should I do?
L2 means low or missing voltage on one leg of the 240-volt supply. Check for a tripped breaker or blown fuse first. If the code stays, have an electrician check the outlet and circuit.
Is F3E2 a moisture sensor or a temperature sensor code?
On current Whirlpool models, Sears PartsDirect lists F3E2 as a moisture sensor failure and F3E3 as an inlet thermistor failure. Older models use different codes, so check the tech sheet for your exact model.
Sources: producthelp.whirlpool.com, producthelp.whirlpool.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, appliancepartspros.com, producthelp.whirlpool.com, nelihome.com, washerfixlab.com. Codes and meanings can vary by model; check your owner's manual.